Welland BFSCALE Smart Body Fat Scale Instruction Manual

Welland BFSCALE Smart Body Fat Scale

Warnings

• Do not disassemble, squeeze, puncture, or short-circuit the device.
• Do not put the device into water or fire.
• Do not expose the device to an environment at a temperature higher than 60℃ （140℉）

Important Notice

• All data measured by this smart body fat scale is for reference only and should not be used for medical diagnosis.
• The measured data may be inaccurate if:
• you are a minor
• you are pregnant
• Do not use this device if you have implanted a cardiac pacemaker or any other medical device.

Warnings

• This device contains lithium batteries and should be placed away from heat sources(heaters, stoves, fireplaces, etc.).
• This device is not water-proof. Do not use it on rainy days or wash it directly with water, otherwise, it will cause damage.
• Do not disassemble or repair this device by yourself. Improper operation during maintenance may cause battery explosion.
• This device is not intended for people (including children)who are weak, slow to respond or have mental disorders unless they are supervised or instructed by the person responsible for their safety on how to use the device.
• Keep the device out of reach of children. Supervise children not to play with the device.

Maintenance

• Carefully wipe the device with a clean, soft cloth.
• Do not use any detergent

Product Structure

Note

• After being placed on hard and flat ground, the screen will turn on when it senses a weight of more than 5kg.
• If this device contains 3 PCs x AAA batteries, please load the battery at the positive and negative electrode instructions.
• If the scale has built-in 3pcs x AAA batteries in the factory, please remove the insulation sheet.

VA display

Note: The screen among different models varies, please refer to the actual product for details.

VA Screen Display Sequence

Note: The screen is running to indicate that it is measuring. Do not leave the scale at this time. Please wait until the measurement will be completed. Then the screen will display Above test results, including body fat rate, BMI, muscle, body water rate, and bone, which are shown for 3 seconds each data.

SPECIFICATION

• Weight unit: kg/lb/st (switch the units via the APP setting or via the unit button at the scale base)
• Weight limit: 5kg-180kg
• Power Supply: 3pcs x AAA
• Account number: No limitation (each account can add 24 persons)
• Height Record: Allows you to record the height info under 16 years old
• Operating temperature: 10-400C
• Operation humidity: 20%-90%

Install Fitdays App

1. Search “Fitdays” in App Store or Google Play or scan the QR Code below:
2. Download and install the App on your device.
3. The App icon will appear on your phone or tablet after the installation is completed.

Support Devices:

• iOS 8.0 or higher
• Android 6.0 or higher

Special Notice Points

1. First-time use: must be online use. (Otherwise, the scale only shows weight & BMI) During use, please keep the App on the home page, and keep measurement posture for about 30S. When finishing the measurement, you can check 6 core data in scale VA display. You also can check more details on the App page.
2. From second-time use, support offline measurement. (No need to open the App for every measurement)

How to use Fitdays APP

1. Step the scale to turn it on.

2. Place the scale on the hard, flat ground.
   Turn on Bluetooth on your smartphone or tablet.

3.  Register your own ID by email or social media account for Fitdays App.

4. Add personal data and confirm OK;
   Note: Enter the wrong gender, age, and height info may result in the measurement being inaccurate.

5. Pair the scale through Bluetooth. Click Account →Device → +→ Searching Bluetooth for paring to find the scale (Keep scale on) and now your phone is connected with the scale;
   After connection, connected will be indicated on the Main page, top position; If disconnected is shown, means failure for pairing. Please repeat the above steps.

6. Tap your foot on the scales to activate the display. Wait until the display shows “0.0” (kg/lb/st). Keep Fitdays App on the main page; Then Bluetooth connection icon will be shown on the VA display. The connected indication will be shown on the main page at the same time.

7. Step onto the scale with bare feet;
   Make sure that stand on each two electrodes metal plates with bare feet as in the below indication photos;
   Note:
   If stepping on the scale with socks, or weighing posture is not correct, only weight and BMI will be measured and displayed on the main page. To get complete data, please step on the scale with bare feet and with the correct posture.

8. The number on the display is flashing when the scale is weighing and analyzing. Please stand still and keep the same posture for about 30S; the App will show the measurement schedule with music playing during body fat measurement. After the measurement is finished, you can check more data from the App. At the same time, you can track 6 core data on the VA screen also.

9. You can click More Data to read more Parameter data.

10. You can find the analyzing report on Body Weight, BMI, BFR, Muscle, Bone Mass, etc. When you click Record, you can see your long-term track chart form.

11. Add, switch user by clicking ->Add User, or click Account–> Add User, then add personal data. The Smart Scale can recognize which user is stepping on it and remind the user to switch to the correct user. Each account can support 24 users;

12. Weighing baby: click + –>Baby Mode. Step on the scale on your own, after the scale, get your weight and then hold the baby to get the weight of the baby.

Battery and Fault Reminders

TROUBLESHOOTING GUIDE

1. Bluetooth not connected

   • The scale and smartphone must both have Bluetooth on.
   • Check the iOS version of the smartphone, it must be iOS 8.0 or higher/Android 6.0 or higher.
   • Click Account →Device→ +→ Searching Bluetooth for paring to find the scale (Keep scale on status) and
     now your phone is connected with the scale.

2. No body fat data was measured when weighing

   • The user must be barefoot to measure the body fat.
   • Do pay attention to correct handlebar grip posture during measurement.
   • Make sure your feet and the scale are both dry.
   • The scale not finishing weighing when the number display is flashing (Keep standing on the scale for around 30 seconds until the number on the display stops flashing).
   • Bluetooth is not turned on.
   • Bluetooth is paired with a different scale.

3. The scale is producing inconsistent weight.

   • Check whether the scale is on a hard, flat surface.
   • Check each sensor foot on the back to make sure nothing is stuck to the bottom of it.
   • Remove the batteries to restart the scale.

4. The App displays the incorrect fat-muscle ratio

   • The body parameter setting is incorrect, check to make sure you entered the correct gender, height, and age.

5. How do I re-calibrate the scale after moving it or changing the batteries?

   • Step on the scale to turn it on. Let it automatically drop to 0.0kg to calibrate.

6. The scale does not turn on

   • Remove the batteries and put them back. Make sure to insert the batteries in the correct direction.

7. The scale only shows weight & BMI.

   • For first-time use, every user needs to use online mode and connect with App for successful measurement. Otherwise, the scale will only weigh & BMI.
   • For every time use, need to hold up the handlebar, and confirm the correct grip posture, especially for thumb & four fingers contact posture. Otherwise, the scale will only weigh & BMI.
   • Keep feet apart, and bear feet onto the scale platform, face to display direction. Otherwise, the scale will only weight & BMI
   • Keep standing still for about 20-30s to finish the whole measurement. Otherwise, the scale will only weigh & BMI.

FCC STATMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>