Guangdong Welland Technology ER301 Smart Body Tape Measure User Manual

June 5, 2024
Guangdong Welland Technology

Guangdong Welland Technology ER301 Smart Body Tape Measure

Product Structure

Guangdong Welland Technology ER301 Smart Body Tape
Measure FIG 1

Tips: Please install the battery before using Ugramo Smart Device.

Before Measuring

  • Please pull out the power insulation sheet first. And install the battery (lxCR2032) correctly.
  • Please turn on your mobile phone’s Bluetooth.
  • Download and install the application “Fitdays”. Guangdong Welland Technology ER301 Smart Body Tape Measure FIG 2
  • Open the Fitdays, and create an acCOunt.
  • Go to “Account” – “Device’ – “+” to search for a device, and then select your device to pair.
  • When icon  appears on the screen of the tape measure, that means the device has connected successfully with the App.

Start Measuring

Power on/Power off

Shortly press the or pull out the tape measure to start the device. The device will power off automatically in 10 seconds if no operation is performed.

Unit/Mode Switch
After starting the device, short press to switch inch and centimeter Guangdong Welland Technology ER301 Smart Body Tape Measure FIG
5

Girth Measurement Mode is the default setting. Long press to shift to Straight Mode. Guangdong Welland Technology ER301 Smart Body Tape Measure FIG
6

Under measurement, shortly press to confirm the value.

Clear
In the pOwer-on status, press and hold on for 2s until the screen shows 0.0cm/inch, this means that zeroing is complete. Guangdong Welland
Technology ER301 Smart Body Tape Measure FIG 8

How to Use Fitdays APP

  • Pair the tape measure With the App “Fitdays”.
  • Open the app, press “+” – “Circumference'”, and measure following the instructions.
  • The body part measured will be Consistent with the App interface. When you press the M to confirm, in the app it will automatically move to the next body part. Meanwhile, the body part that completes the measuring will SWitch to grey.
  • If you want to measure any body part again, just select it on your phone.
  • After completing measuring all the body parts, just press the Save button at the bottom to save all the data.
  • Then press the Reset button to retract the tape measure and the screen returns to zero.
  • If you want to view the previously saved data, click the”Chart” on the home page of the App. then click the ruler icon in the upper right corner to view the previously saved data Guangdong Welland Technology ER301 Smart Body Tape Measure FIG 9

Simple Troubleshooting Method

Guangdong Welland Technology ER301 Smart
Body Tape Measure FIG 10

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Warning : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. The equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  1. Reorient or relocate the receiving antenna.
  2. Increase the separation between the equipment and receiver
  3. Connect the equipment into an outlet on a circuit different from that to which the receiver is Connected.
  4. Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals