Raex YR2119 Wireless Remote Transmitter Instructions

Raex YR2119 Wireless Remote Transmitter

Product Information

The product is a motorized window covering system that can be remotely controlled using a wireless transmitter. The system allows users to set up limit points for the window covering and reset intermediate positions. The wireless transmitter uses the ASK frequency modulation mode and has 20 encoder channels. It is powered by a CR2032 battery and has four buttons for channel selection, open/stop/close, and sending codes. The system also allows for setting up paired remote controls and locking specific channels.

Product Usage Instructions

Disallowing the Hand-Pull Function and Deleting Limits

1. Press the [Stop] and [Down/Close] buttons simultaneously to disallow the hand-pull startup function and clear limits.
2. To delete remote control channels, follow the steps under “Delete remote control channels” in the remote control functions section below.

Setting Up/Open Limit Point and Set Down/Off Limit Point

1. Press [Send code button] and [On/Open] at the same time to remotely control the motor to run to the required limit position for setting up/open limit point.
2. Press [Send code button] and [Down/Close] at the same time to remotely control the motor to run to the required limit position for set down/off limit point.
3. Press the motor Learn Code button or Setting Code button to confirm the position.

Resetting Intermediate Positions

1. Press [Send code button]+[75%] simultaneously to set intermediate position 1.
2. Press [Send code button]+[50%] simultaneously to set intermediate position 2.
3. Press [Send code button]+[25%] simultaneously to set intermediate position 3.
4. Press the motor Setting Code button to confirm each intermediate position.

Wireless Transmitter Instructions

1. Install the CR2032 battery into the transmitter.
2. The transmitter LED will light up for 1 second and then turn off, indicating initialization.
3. The default channel is the first channel, which is selected when the battery is first installed. The current channel will be restored each time the battery is replaced.
4. To pair a remote control to the motor, follow the steps under “Paired remote control Settings” in the remote control functions section below.
5. To lock specific channels, press the [Left] or [Right] button to select the number of channels to be locked. The system will reserve the channels from the beginning up to the selected channel number.

Remote Control Functions

1. To set up a paired remote control, follow these steps:
   • Press the motor Setting Code button for 3 seconds until the LED light turns on.
   • Select the desired channel on the front of the remote control.
   • Turn the remote control over and press the [Send code button] for 3 seconds until the motor driver indicator flashes.
   • Press the motor Setting Code button to confirm and finish the channel setting process.
2. To delete a remote control channel, follow these steps:
   • Press the motor Setting Code button for 3 seconds until the LED light turns on.
   • After the LED light turns on, release the button and press it again for 7 seconds until the LED light turns off. This will clear the channel.

Specification

Install the battery

1. Initialization : After the battery is installed as shown in the picture, the LED plane will light up for 1 second and then turn off. The remote control will be initialized.
2. Default first channel: the factory remote control first installed battery, the default current channel is the first channel; Each time the battery is installed in the future, the current channel will be restored to the selected channel before removing the battery.

Remote control functions

Paired remote control Settings

Note: The paired remote control shall be set together with the motor.
The operation steps are as follows:

1. Enter into setting code status
   Press motor [Setting code] 3 seconds until the LED light on.

2. Select the remote control to set the channel:
   After selecting the channel value on the front of the remote control, turn the remote control over immediately, press [Send code button] button for 3 seconds, until the motor driver indicator flashes.

3. Confirm
   Press motor [Setting code] to confirm it and finish the channel setting process.

Delete remote control channels
Note: The paired remote control shall be set together with the motor.
The operation steps are as follows:

1. Enter into setting codes status
   Press motor [Setting code] 3 seconds until the LED light on.

2. Delete remote control channels
   At first,release.Press motor [etting code] 7 seconds until the LED light off and finish the clear channel process.

3. Set channel locking [Channel Locking] : Press the channel [Left] or [Right] button to select the number of channels to be locked. After locking, the number of channels from the beginning of the channel to the number of channels to be locked is reserved.

Button control function

1. LED Indicator:
   The LED flashes to indicate that the signal is transmitting.

Encoder Channel selection:

1. Single control mode
   Press the channel [Left] or [Right], the LED light is on, the screen displays the corresponding channel number, you can select the curtain motor controlling the corresponding digital channel.

2. Group control model
   Press [Left] and [Right] at the same time, and the screen will display “AL”, that is, the group control mode will be started; Press [Left] and [Right] again to exit the group control mode.

Tilting function and 3 favourite limits function

1. Tilting function
   Operating Instructions:
   Press the button in the figure above to open the up tilt, horizontal and down tilt for blind venetian.

2. 3 favourite limits:
   the remote control features, do not need to set the limit points, one button can reach 75%, 50%, 25%, three sites.
   Operating Instructions:
   Long press the button in the figure above to open the curtain to 75%, 50% and 25% positions.

Combination key function

Note: the following remote control function, part of the curtain motor is not equipped, please consult the relevant product sales personnel.

1. Enter into setting code status
   Press motor [Setting code] 3 seconds until the LED light on.

2. Select the required functions and operate according to the steps:
   Note: The following operations should be completed in the state of motor code learning.

3. Change direction function
   [Left]+[Stop]: Press the [Left]+[Stop] button under the state of motor code learning, and the motor will enter the reversing function.

4. Enable the pull start function
   [Stop]+[Up/Open] : Press the [Stop]+
   [On/Open] button for 5 seconds at the same time to start the hand pull function.

5. Disallow the hand-pull function
   [Stop]+[Down/Close] : Press the [Stop]+ [Down/Close] button for 5 seconds at the same time to prohibit hand-pull startup function.

6. Delete limits
   [Send code button]+[Stop] : Press [Send code button] and [Stop] at the same time to clear limits.

7. Set up/open limit point
   [Send code button]+[On/ ] : Press [Send code button] and [On/ ] at the same time to remotely control the motor to run to the required limit position, and press the motor “Learn Code” button to confirm.

8. Set down/off limit point
   [Send code button]+[Down/Close] : Press [Send code button] and [Down/Close] at the same time to remotely control the motor to run to the required limit position, and press the motor “Setting Code” button to confirm.

9. Reset intermediate position 1
   [Send code button]+[75%] : Press [Send  code button] and [75%] simultaneously toset the IP1.

10. Reset intermediate position 2
    [Send code button]+[50%] : Press [Send code button] and [50%] simultaneously to set the IP2.

11. Reset intermediate position 3
    [Send code button]+[25%] : Press [Send code button] and [25%] simultaneously to set the IP3.

12. Confirm
    Press motor [etting code] to confirm it and finish the channel setting process.

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>