REDARC LBAT12060 Lithium Deep Cycle Battery User Manual
- October 30, 2023
- REDARC
Table of Contents
- REDARC LBAT12060 Lithium Deep Cycle Battery
- Product Information
- Product Usage Instructions
- LITHIUM DEEP CYCLE BATTERY
- WARNING AND SAFETY INSTRUCTIONS
- Specification/Dimension
- USER GUIDE
- PARALLEL CONNECTION
- WARRANTY
- CONTACT
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
REDARC LBAT12060 Lithium Deep Cycle Battery
Product Information
The REDARC Lithium Deep Cycle Battery is a high-performance battery that is equipped with an internal Battery Management System (BMS) to monitor and optimize each cell during charge and discharge. The battery is available in four different models, namely LBAT12060, LBAT12100, LBAT12100-HD, and LBAT12200. The battery is designed to deliver unrivaled performance and battery life.
WARNING AND SAFETY INSTRUCTIONS
It is important to read and understand the user manual before operating the battery or modifying the installation. REDARC recommends that the battery be installed by a suitably qualified person. Working in the vicinity of a Lithium battery is dangerous and can result in fire, explosion, and burns. It is important to follow the safety instructions when installing and using the battery.
Published Ratings
- The correct cable and fuse sizes must be used when installing this Battery to avoid harm to the installer or user and/or damage to the Battery or other equipment installed in the system.
- Do not smoke or allow a spark or flame in the vicinity of the battery or engine as this may cause the battery to explode.
Notice
It is important to follow the instructions when installing and using the battery to avoid damage to the battery, fire, explosion, and burns.
Caution
- The Battery should not be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they are supervised or have been instructed on how to use the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the Battery.
- Do not alter or disassemble the Battery under any circumstances. Incorrect handling or reassembly may result in a risk of electric shock or fire and may void the unit warranty.
Product Usage Instructions
Below are the usage instructions for the REDARC Lithium Deep Cycle Battery:
- Do not use the battery for cranking/starting applications.
- Do not connect the batteries in series to increase the overall voltage.
- Do not dispose of in fire.
- The battery must be installed away from major heat sources, high voltage, and avoid exposed sunlight for long periods of time.
- Do not connect the positive and negative terminals of battery together.
- Do not allow the battery to sit in a discharged state 10.0 V.
- Use only regulated lithium LiFePO4 battery chargers. Failure to install the correct battery charger will void all warranty.
- Do not mix lithium batteries with other types/chemistries or brands of batteries as they will not be compatible.
Technical Specifications
Model | Part Number | Ah / Wh | Nominal Voltage | Self-Discharge Rate per month |
---|---|---|---|---|
LBAT12060 | LBAT12060 | 60 Ah / 768 Wh | 12.8 V | 3% |
LBAT12100 | LBAT12100 | 100 Ah / 1280 Wh | 12.8 V | 3% |
LBAT12100-HD | LBAT12100-HD | 100 Ah / 1280 Wh | 12.8 V | 3% |
LBAT12200 | LBAT12200 | 200 Ah / 2560 Wh | 12.8 V | 3% |
LITHIUM DEEP CYCLE BATTERY
REDARC Lithium Deep Cycle Batteries are the ultimate in deep-cycle battery technology delivering unrivaled performance and battery life. REDARC Lithium Deep Cycle Batteries are equipped with an internal Battery Management System (BMS) that can monitor and optimise each cell during charge and discharge to protect the battery pack from over charge, over discharge and short circuit.
WARNING AND SAFETY INSTRUCTIONS
Save these instructions — this manual contains important safety instructions for the LBAT Series Lithium Deep Cycle Battery. Do not operate the battery or modify the installation unless you have read and understood this manual and the battery is installed as per these installation instructions. REDARC recommends that the battery be installed by a suitably qualified person.
WARNING
Risk of fire, explosion and burns — Working in vicinity of a Lithium battery is dangerous.
- DO NOT Short the battery terminals
- Do NOT expose the battery to temperatures Beyond the published limits
- DO NOT attempt to disassemble the battery
- Do NOT crush or puncture the battery
- Do NOT submerse the battery in liquid
- Do NOT operate the battery beyond the published ratings
Doing so may result in damage to the battery, fire, explosion and ultimately burns. For this reason, it is of utmost importance that you follow the instructions when installing and using the battery.
CAUTION
- The Battery should not be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are supervised or have been instructedon how to use the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the Battery.
- Do NOT alter or disassemble the Battery under any circumstances. Incorrect handling or reassembly may result in a risk of electric shock or fire and may void the unit warranty.
- Cable and fuse sizes are specified by various codes and standards which depend on the type of vehicle the Battery is installed into. Selecting the wrong cable or fuse size could result in harm to the installer or user and/or damage to the Battery or other equipment installed in the system. The installer is responsible for ensuring that the correct cable and fuse sizes are used when installing this Battery.
- NEVER smoke or allow a spark or flame in vicinity of battery or engine. This may cause the battery to explode.
NOTICE
- Do NOT use the battery for cranking/starting applications
- Do NOT connect the batteries in series to increase the overall voltage
- Do NOT dispose of in fire
- The battery must be installed away from major heat sources, high voltage, and avoid exposed sunlight for long periods of time
- Do NOT connect the positive and negative terminals of battery together
- Do NOT allow the battery to sit in a discharged state ≤10.0 V
- Do NOT use unregulated non-lithium LiFePO4 battery chargers. Failure to install the correct battery charger will void all warranty
- Do NOT mix lithium batteries with other types/chemistries or brands of batteries as they will not be compatible
MODELS
- LBAT12060
- LBAT12100
- LBAT12100-HD
- LBAT12200
Specification/Dimension
LBAT12060
LBAT12060|
---|---
Part Number| LBAT12060
Nominal Capacity (C20, 25 °C to 10.5 V)| 60 Ah / 768 Wh
Nominal Voltage| 12.8 V
Self-Discharge Rate per month| ≤ 3%
Short Circuit Protection| 200 to 500 µs
Continuous Discharge Current (recommended)| 85 A — 40 minutes
Maximum Discharge Current| 100 A — 30 minutes
Peak Discharge Current| 120 A — 5 seconds
Discharge Cut-Off Voltage| 10.0 V
Life Cycles 80% DOD| 2000
Life Cycles 50% DOD| 5000
Life Cycles 20% DOD| 8000
Recommended Charge Current| ≤ 30 A
Maximum Charge Current| 30 A
Recommended Charge Voltage| 14.6 V ± 0.2 V
BMS Charge Cut Off Voltage| 15.6 V
Dimension (L × W × H)| 291 × 106 × 231 mm
Weight| 8.0 kg
Cell Chemistry| LiFePO4
Case Material| Polycarbonate
Terminal Type| M8
Charge Temperature Range| 0 ~ 60 ºC
Discharge Temperature Range| −20 ~ 70 ºC
Storage Temperature Range| −20 ~ 40 ºC
Series Configuration| No
Parallel Configuration| Yes
Compliance| UN38.3
DIMENSIONS
LBAT12100 AND LBAT12100-HD
DIMENSIONS
LBAT12200
LBAT12200|
---|---
Part Number| LBAT12200
Nominal Capacity (C20, 25 °C to 10.5 V)| 200 Ah / 2560 Wh
Nominal Voltage| 12.8 V
Self-Discharge Rate per month| ≤ 3%
Short Circuit Protection| 200 to 500 µs
Continuous Discharge Current (recommended)| 100 A — 120 minutes
Maximum Discharge Current| 170 A — 60 minutes
Peak Discharge Current| 400 A — 5 seconds
Discharge Cut-Off Voltage| 10.0 V
Life Cycles 80% DOD| 2000
Life Cycles 50% DOD| 5000
Life Cycles 20% DOD| 8000
Recommended Charge Current| ≤ 50 A
Maximum Charge Current| 100 A
Recommended Charge Voltage| 14.6 V ± 0.2 V
BMS Charge Cut Off Voltage| 15.6 V
Dimension (L × W × H)| 485 × 170 × 242 mm
Weight| 21.5 kg
Cell Chemistry| LiFePO4
Case Material| Polycarbonate
Terminal Type| M8
Charge Temperature Range| 0 ~ 60 ºC
Discharge Temperature Range| −20 ~ 70 ºC
Storage Temperature Range| −20 ~ 40 ºC
Series Configuration| No
Parallel Configuration| Yes
Compliance| UN38.3
DIMENSIONS
USER GUIDE
REDARC Lithium Deep Cycle Batteries ship with a low state of charge and should be charged prior to first use. The batteries have a self-discharge rate of 3% per month @ 25°C. The battery should not be left for more than 30 days without checking its state of charge.
- Ensure that the battery is stored in a dry, clean, shaded and well-ventilated environment at a temperature range that does not exceed the published temperature range specifications
- Ensure all loads to the battery terminals are disconnected while the battery is in storage
- Keep the battery terminals clean at all times
- Ensure that the battery is free from damage from any force which may damage it, such as being dropped or being stored incorrectly
- Ensure that the battery is used in well-ventilated applications which does not place the battery at risk of exceeding its published charge and discharge temperature range specifications
- If shipping the batteries between locations, please check with local national and/or international authorities to ensure you are complying with transportation guidelines
- To dispose of the battery, please contact an authorised lithium battery recycling facility
PARALLEL CONNECTION
When connecting REDARC Lithium Deep Cycle Batteries in parallel, we recommend that the earth connection be made on the opposite end of the battery bank to the positive connection.
- When the batteries are wired this way, the effects of resistance in the POS+ and NEG− wires cancel each other out and both batteries receive a more equal charge
- This is to minimise the effects around unequal charge and discharge rates whereby older/traditional wiring methods result in the first battery receiving more charge and uneven discharge than the second battery.
- Make sure all cabling is not undersized for the
battery system/charger and ensure the battery cables are connected to the terminals correctly. Batteries must be installed by a suitably qualified person.
SERIES CONNECTION
- Do not connect REDARC Lithium Deep Cycle Batteries in series. The BMS’s used in the batteries, if connected in series, are unable to operate due to voltage differences.
WARRANTY
LIMITED WARRANTY
For full warranty terms and conditions, visit the Warranty page of the REDARC
website:
www.redarcelectronics.com/warranty
Australia, New Zealand & Europe REDARC Electronics Pty Ltd 23 Brodie Road
(North), Lonsdale SA 5160 Australia
North America REDARC Corporation c/o Shallco, Inc. 308 Component Dr.
Smithfield, NC 27577 USA
Australia +61 8 8322 4848
New Zealand +64 9 222 1024
UK & Europe +44 (0)20 3930 8109
USA + 1 (704) 247 5150
Canada + 1 (604) 260 5512
Mexico + 52 (558) 526 2898
IMPORTER CONTACT INFORMATION
UK
Ozparts UK Ltd 1 Prospect Place Pride Park DE24 8HG, Derby UK
Europe
Ozparts Pl sp. z o. o. ul. Slowackiego 32/5 87−100 Torun Poland
Design, product configuration and technical specifications are subject to
change without notice.
Copyright © REDARC Electronics
Pty Ltd. All rights reserved.
REDARC® and THE POWER OF REDARC® are trademarks of REDARC Electronics Pty Ltd.
REDARC Electronics Pty Ltd ABN 77 136 785 092
REDARC Electronics Pty Ltd, 23 Brodie Road (North), Lonsdale SA 5160,
Australia
CONTACT
Tech Support
1300 REDARC
Head Office
+61 8 8322 4848
New Zealand
+64 9 222 1024
UK & Europe
+44 (0)20 3930 8109
USA
+1 (704) 247-5150
Canada
+1 (604) 260-5512
Mexico
+52 (558) 526-2898
redarcelectronics.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>