BaBylissPRO FX870GBPUZ Professional Cord Cordless Lithium Clipper Instruction Manual

October 30, 2023
BaBylissPRO

Operating Instructions
Model FX870GBPUZ
Professional
Cord/Cordless Lithium ClipperBaBylissPRO FX870GBPUZ Professional Cord
Cordless Lithium Clipper -

For your safety and continued enjoyment of this product, always read the instruction book carefully before using.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, especially when children are present, basic safety precautions should always be taken, including the following:
READ ALL INSTRUCTIONS BEFORE USING
KEEP AWAY FROM WATER

DANGER – Any appliance is electrically live, even when the switch is off.To reduce the risk of death or injury by electric shock:

  1. Always unplug appliance from electrical outlet immediately after using (except when charging unit).
  2. Do not place or store appliance where it could fall or be pulled into a tub or sink.
  3. Do not use appliance while bathing or in the shower.
  4. Do not place appliance in, or drop into water or other liquids.
  5. If appliance has fallen into water, do not reach for it. Unplug immediately.
  6. Unplug this appliance before cleaning.

WARNING – To reduce the risk of burns, electric shock, fire, or injury to persons:

  1. Never leave a plugged-in appliance unattended.
  2. They cannot be used by children aged 8 years or over and by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they have been given supervision or instructions regarding the use of the device in complete safety and provided they understand the dangers involved. Children must not play with the appliance. Cleaning and maintenance by the user must not be carried out by children without supervision.
  3. Use appliance only for its intended use as described in this manual. Use only attachments recommended by the manufacturer. Do not use an extension cord to operate the appliance.
  4. Never operate the appliance if it has a damaged cord or plug, is not working properly, has been dropped or damaged, or dropped into water. Return the appliance to a BaBylissPRO Service Center for examination and repair.
  5. Keep the appliance cord away from heated surfaces.
  6. Do not pull, twist or wrap the cord around the appliance.
  7. Never drop or insert any object into any opening on the appliance.
  8. Do not place the appliance on any surface while it is operating.
  9. Do not use the appliance with a damaged or broken comb or with teeth missing from the blades, as injury may result. Before each use, make certain the blades are aligned properly and oiled.
  10. Do not use the appliance outdoors or where aerosol (spray) products are being used or where oxygen is being administered.
  11. Do not crush, or heat above 212° F (100° C) or incinerate the appliance, due to risk of fire, explosion or burns.
  12. Always attach plug to appliance first, then to outlet. To disconnect, turn all controls to OFF position then remove from outlet.
  13. Children must be supervised to ensure that they do not play with the appliance.

SAVE THESE INSTRUCTIONS

OPERATING INSTRUCTIONS

  1. Before using the clipper for the first time, charge continuously for 3 hours.
    Maximum battery capacity will only be reached after 3 charging and discharging cycles.

  2. Make sure the switch on the clipper is in the OFF position. Connect the charging jack into the receptacle on the bottom of the clipper. Plug the adapter into any electrical outlet (at the voltage listed on the label affixed to the adapter). The charging indicator
    will light up blue to indicate that the charging has begun. Charging is complete after 3 hours.

  3. The adapter may become warm while charging. This is normal.

  4. Preserving the batteries: In order to maintain the optimum capacity of the rechargeable batteries, the clipper should be recharged for 3 hours approximately every 6 months.

  5. Make sure the switch is in the OFF position when the clipper is not operating.

  6. If the charging light starts to flash rapidly (more than 4 flashes per second) then the appliance is faulty. If this happens then please stop charging and remove the adapter from the mains and contact an authorized Service Center.

FOR DIRECT PLUG-IN OPERATION
Make sure clipper is off. Connect charging jack into the receptacle at the end of clipper and plug the adapter into power outlet.
ON/OFF SWITCH
To operate, simply slide switch to ON (marked ” I”). To stop operation, set to the OFF (marked “º “) position.
VERY IMPORTANT: Blades must be cleaned and oiled on a regular basis for proper functioning. Failure to regularly clean and oil the blades will void the warranty.

USER MAINTENANCE INSTRUCTIONS

MAINTENANCE OF THE BLADE
Always apply oil to the blades before and after use. This will ensure maximum cutting performance and proper maintenance. Hold the clipper away from your body in a downward position, and apply a drop of BabylissPro lubricating oil on the front and sides of the cutter blade. Wipe off excess oil with a soft, dry cloth. Do not pull, twist, or wrap the supply cord around the appliance.
HOW TO USE COMB ATTACHMENTS
To use the comb attachments, turn the clipper to “ ” position. Slide the comb attachment onto the top of the clipper blade, and then pull down and over the back of the blade. To remove, pull up on the back of the comb attachment and then pull away from the blade.

REPLACEMENT (REMOVAL) OF BLADE SET
Step 1. Unplug the unit and adjust the taper (see illustration A).
Step 2. Remove the screws and the fixed blade. Save the screws.
Step 3. Lift off the small moving blade and replace it with the new one on the plastic oscillator (see illustration B).
Step 4. Replace the fixed blade using the screws and lightly tighten them. Adjust the teeth as shown in illustration C, to a gap of 1/32″ (1 mm) to 1/16″ (1.5 mm), and the small, moving blade as centered and parallel as possible to the fixed blade’s teeth.

IMPORTANT NOTE:
The top edge of the fixed blade must be a minimum of 1/32″ (1 mm) higher than the top edge of the moving blade, as centered as possible. This is important so that the moving blade does not come in contact with the skin.
Be sure to add a few drops of BabylissPro lubricating oil to the blades before running.
Don’t forget to tighten the screws after the blades have been aligned.

BaBylissPRO FX870GBPUZ Professional Cord Cordless Lithium Clipper -
fig3

ADJUSTABLE TAPER LEVER
The taper lever is positioned at your thumb. You can hold the clipper in your hand and adjust the lever at the same time – while you are clipping.
The taper lever adjusts the closeness of the cut from a close cut with the taper lever in the up position, to a longer length cut with the taper lever in the down position. To increase cutting length, slowly push the lever down. To cut closer, push the lever up. As different cutting edges are used in each setting, using the taper lever lengthens the life of the clipper blades. Too much hair can slow down hair clippers. Keep the clipper on for removing hair. Then push the taper lever back and forth quickly for several times. If you do this every time, especially after much hair cutting, the clipper blades should remain free of cut hair. Oil the blades after the above procedures.

DISPOSAL OF LITHIUM ION BATTERY

This clipper has a lithium ion battery. To protect the environment, these batteries should be removed and properly disposed of when the unit is no longer operating. To remove the battery block for disposal or recovery, follow these instructions:

  1. Disconnect the clipper from household outlet.
  2.  Discharge the battery pack completely before removing.
  3. Remove the blade and bottom cap.
  4. Remove 4 screws and open cover.
  5. Remove the screw that fastens the printed circuit board to housing. Lift printed circuit board out.
  6.  Unplug lithium ion battery.
  7.  To protect the environment, do not dispose of your battery with your ordinary household waste. For more details on recovery of material and waste-treatment facilities, please contact the waste disposal services in your region.

CONTAINS LITHIUM ION BATTERY. MUST BE COLLECTED, RECYCLED OR DISPOSED OF PROPERLY. DO NOT DISPOSE OF IN THE MUNICIPAL WASTE.

PRODUCT FEATURES

  1. 8 comb attachments

  2. Power adapter:
    Model No.: C045120-EU
    Input: 100-240V~ 50-60Hz 0.2A Max
    Output: 4.5V **** 1200mA 5.4W

  3.  LED charge indicator light
    a. LED BLUE Blinking – Charging
    b. LED BLUE – Fully Charged
    c. LED BLUE Flashing – 10 minutes battery left

BEFORE USING THE CLASS 2 POWER SUPPLY, READ THESE INSTRUCTIONS CAREFULLY.

Use only with adapter Model No.: C045120-EU which is provided.
Rated input voltage: 100-240V~ 50-60Hz 0.2A Max
Rated Output: 4.5V 1200mA 5.4W

OPERATION

  1. For dry location use only. Do not expose to water.
  2. When not in use, unplug unit completely.
  3. Unit will become warm during operation.

CAUTION

  1. Dry location use only. Do not expose to liquids, vapor, or rain.
  2. Ensure jack is plugged into the clipper unit before plugging the adapter into the outlet.
  3. Do not operate any appliance that has a damaged output cord or housing.
  4. Always unplug the unit before cleaning or when not in use.
  5. Be sure voltage is correct before plugging in. For connection to power supply not in the U.S.A. use an attachment plug adapter of the proper configuration for power outlet. The included adapter automatically adjusts to the input voltage. DO NOT USE A VOLTAGE CONVERTER.

Clipper CHARGING PRECAUTIONS

  • Avoid charging the battery at temperatures below 41° F (5° C) or above 95° F (35° C).
  • Avoid charging the battery in direct sunlight or near a radiating heat source.
  • Even though the clipper may not be used for an extended period, charge once a month to preserve battery life.
  • The power cord cannot be replaced. If it is damaged, the AC adapter should be discarded.

Clipper OPERATING PRECAUTIONS

• This clipper has a built-in rechargeable battery. Do not throw into fire, apply heat, or charge, use, or leave in a high-temperature environment.

  1. The battery must be removed from the device before disposal.
  2. The appliance must be disconnected from the power supply when removing the battery
  3. The battery must be removed for disposal in a safe manner

WARNING:
IF YOU THINK THE POWER IS OFF WHEN THE SWITCH IS OFF, YOU’RE WRONG.

Everyone knows that electricity and water are a dangerous combination. But did you know that an electrical appliance is still electrically live even if the switch is off? If the plug is in, the power is on. So when you are not using the appliances, keep them unplugged.

©2022 BaBylissPRO
IB-22/123

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

BaBylissPRO User Manuals

Related Manuals