PIT BOSS 11004 5 Burner Deluxe Griddle User Guide

PIT BOSS 11004 5 Burner Deluxe Griddle

IMPORTANT SAFEGUARDS

IMPORTANT, READ CAREFULLY, RETAIN FOR FUTURE REFERENCE. MANUAL MUST BE READ BEFORE OPERATING!

MAJOR CAUSES OF APPLIANCE FIRES ARE A RESULT OF POOR MAINTENANCE AND A FAILURE TO MAINTAIN REQUIRED CLEARANCE TO COMBUSTIBLE MATERIALS. IT IS OF UTMOST IMPORTANCE THAT THIS PRODUCT BE USED ONLY IN ACCORDANCE WITH THE FOLLOWING INSTRUCTIONS.

WARNING: Please read the entire manual before installation and use of this electric, pellet fuel burning appliance. Failure to follow these instructions could result in property damage, bodily injury, or even death. Contact local building or fire officials about restrictions and installation inspection requirements in your area. Save these instructions.

SAFETY LISTING

In accordance with the procedures and specifications listed in the ANSI Z21.58-2018 / CSA 1.6-2018 “Outdoor Cooking Gas Appliances.” Pit Boss® Grills cooking appliances have been independently tested and listed by CSA (an accredited testing laboratory) to CSA standards.

PROPOSITION 65 – CALIFORNIA

WARNING: This product can expose you to chemicals including formaldehyde, which is known to the state of California to cause cancer, lead and lead compounds, which are known to the state of California to cause cancer and birth defects or other reproductive harm, and Carbon Monoxide, which is known to the state of California to cause birth defects or other reproductive harm. For more information go towww.P65Warnings.ca.gov.

DANGERS AND WARNINGS

If you smell gas, shut off gas to the appliance. Extinguish any open flame, open the lid. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department.

Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

GRIDDLE INSTALLATION CODES
The installation must conform with local codes or, in the absence of local codes, with either the national fuel gas code, ANSI Z 223.1/NFPA 54, Natural gas and propane installation code, CSA B149.1, or propane storage and handling code, B149.2. LP gas griddle models are designed for use with a standard 20 lb. Liquid Propane Gas tank, not included with griddle. Never connect your gas griddle to an LP gas tank that exceeds this capacity.

You must contact your local home association, building or fire officials, or authority having jurisdiction, to obtain the necessary permits, permission, or information on any installation restrictions, such as any griddle being installed on a combustible surface, inspection requirements or even ability to use, in your area.

1. A minimum clearance of 1,270 mm (50 inches) from combustible constructions to the sides of the griddle, and 1,270 mm (50 inches) from the back of the griddle to combustible constructions must be maintained. Do not install appliance on combustible floors, or floors protected with combustible surfaces unless proper permits and permissions are obtained by authorities having jurisdiction.
   Do not use this appliance indoors, in an enclosed or unventilated area, inside homes, vehicles, tents, garages. This appliance must not be placed under overhead combustible ceiling or overhang. Keep your griddle in an area clear and free from combustible materials, gasoline and other flammable vapors and liquids.
   Should a grease fire occur, turn the griddle OFF until the fire is out. Do not throw water on. Do not try to smother the fire. Use of an all-class (class ABC) approved fire extinguisher is valuable to keep on site. If an uncontrolled fire does occur, call the Fire Department.

2. The liquefied petroleum (LP) cylinder must be constructed and marked in accordance with the specifications for LP Gas Cylinders of the U.S. Department of Transportation (D.O.T.) or the National Standard of Canada, CAN/CSA-B339, Cylinders, Spheres and Tubes for
   Transportation of Dangerous Goods; and Commission.

3. This outdoor griddle is not intended for installation in/on recreation vehicles or boats.
   Never use this appliance in an enclosed space, such as a camper, tent, car, boat, or home. This appliance is not intended for and should never be used as a heater.

4. This appliance is not recommended for children, persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are under direct supervision or instruction by a person responsible for their safety.

5. Parts of the barbecue may be very hot, and serious injury may occur. Keep young children and pets away while in use. Do not touch hot surfaces. Use heat-resistant gloves, long-handled tongs, or cooking mitts at all times, since the griddle will become very hot.

6. Never use the griddle without the grease cup installed. Without the grease cup, hot grease and debris could leak downward and produce a fire hazard.

7. Do not obstruct the flow of combustion and ventilation air to this appliance. Keep the burner tube and portholes clean and free from debris. Clean before use. Regular care and maintenance is required to prolong the lifespan of your unit.

8. Always check for gas leaks when you connect and disconnect the regulator to the gas cylinder, especially after a period of storage (for example, over winter). Check all connections for leaks with a soapy water solution and brush. Never use an open flame to check for leaks.

9. Clean and inspect the gas regulator before each use of the outdoor cooking gas appliance. Replace the gas regulator prior to being used
   if there is evidence of excessive abrasion or wear. Use only the gas regulator assembly that has been supplied with this gas griddle. Do not use a regulator from another manufacturer.
   Do not use lava rock, wood chunks, charcoal, lighter fluid, alcohol, or other similar chemicals for lighting or relighting. Keep all such substances and liquids well away from appliance when in use.

10. Operate this appliance using liquefied petroleum only, which is also specified on the rating label on the unit. Do not attempt to operate your griddle on other gases. Do not attempt to convert this LP unit to natural gas. Failure to follow this warning could lead to fire, bodily harm, and will void your warranty.

11. The location of the burner tube with respect to the orifice is vital for safe operation. Check to ensure the orifice is inside the burner tube before using the gas griddle. If the burner tube does not fit over the valve orifice, lighting the burner may cause explosion and/ or fire.

PROPANE GAS WARNINGS

1. Ensure the gas cylinder is purchased by a reputable supplier. An incorrectly filled or an overfilled LP tank can be dangerous. The overfilled condition combined with the warming of the LP gas tank (a hot summer day, tank left in the sun, etc.) can cause LP gas to be released since the temperature increase causes gas to expand. Gas released from the cylinder is flammable and can be explosive.

2. Do not use an LP gas cylinder if it has a damaged valve or shows signs of dents, gouges, bulges, fire damage, corrosion, leakage, excessive rust, or other forms of visual external damage; it may be hazardous and should be checked immediately by a liquid propane supplier.
   If you see, smell, or hear the hiss of gas escaping from the cylinder, do not attempt to light appliance. Extinguish any open flame. Disconnect from fuel supply.

3. Do not connect or disconnect the gas cylinder while the unit is in use or is still hot. When griddle is not in use, ensure regulator knob is turned to OFF and disconnect the gas cylinder. Never move or transport the unit while the gas cylinder is attached. Do not store a spare LP gas cylinder under or near the appliance.

4. Cylinders must be stored outdoors out of reach of children and must not be stored in a building, garage, or any other enclosure area.

CARBON MONOXIDE

Carbon monoxide is a colorless, odorless gas that from poisoning you, your family, or others. Know the symptoms of carbon monoxide poisoning: headache, dizziness, weakness, nausea, vomiting, sleepiness, and confusion. Carbon monoxide reduces the blood’s ability to carry oxygen. Low blood oxygen levels can result in loss of consciousness and death.

• See a doctor if you or others develop cold or flu-like symptoms while cooking or in the vicinity of the appliance. Carbon monoxide poisoning, which can easily be mistaken for a cold or flu, is often detected too late.
• Alcohol consumption and drug use increase the effects of carbon monoxide poisoning.

Carbon monoxide is especially toxic to mothers and children during pregnancy, infants, the elderly, smokers, and people with blood or circulatory system problems, such as anemia, or heart disease.

PACKAGE CONTENTS

1 x| GRIDDLE & PARTS
1 x| ASSEMBLY GUIDE
SPECIFICATIONS

MODEL| PB5BGD1
FUEL TYPE| PROPANE GAS
BTU| 62,000
DIMENSIONS| 1,960 X 630 X 895 MM /

77.1 X 24.8 X 35.2 IN

WEIGHT| 57.5 KG / 126.7 LB

GETTING TO KNOW YOUR GRIDDLE

A Gas Cylinder Hook
Holds the gas cylinder and can fold away for storage while disconnected.
B Regulator Assembly
The attachment connects the gas cylinder and the griddle unit.
C Locking Pin
Secures the legs of the griddle in place. The pins can be pulled to collapse the unit for storage.
D Gas Tank Bracket
Supports the gas cylinder. It can fold away when the cylinder is disconnected.
E Lid/Prep Shelves Area
Lock the shelves after the griddle has cooled to cover the cooking surface or as a prep area while using your griddle.
F Side Handles
Use this handle on the side to tilt and move the griddle from one area to another.
G Grease Cup
Captures the cooking grease from the griddle to keep a clean, cooking area.
H Control Knobs
Used to ignite and control the flame height during cooking.
I Bottom Shelf
The sturdy, open-cart design is perfect for keeping barbecue tools and seasonings off the ground.
J Griddle Lid Latch
Secures the lid prep shelves after the griddle has cooled while the unit is stored.
K Griddle Top
The cooking area of the griddle

|
---|---

CONTROL KNOB

A Off
The starting position of the control knob.
B Control Knob
This controls the ignition and height of the flame. Press in and turn counter- clockwise to the ignition icon to light the griddle, then adjust the flame height.
C Flame Height
The range shown is the Ignition/ HIGH setting, the flame tip will be a slight yellow. It will range from a Slight Blue in on medium to a “LO” setting that is dark blue.
D Ignition
The position on where you would press in and turn counter-clockwise to ignite the grill. This is also the HIGH position for the flame height.
E Low Flame
The lowest flame height, dark blue color.

TIP: Create temperature zones on the griddle top with the five control knobs.

CONNECTING TO A GAS SUPPLY

GAS CYLINDER REQUIREMENTS

The griddle is set and tested with liquid propane gas only. The regulator supplied is set for 27.94 cm (11 inch) water column (WC) and is for use with LP gas only. The factory-supplied regulator and hose must be used with a 9 kg (20 lbs) LP gas tank. Contact your gas supplier for a special regulator for bulk gas that fuels other appliances.

CAUTION: It is important to inspect the full length of the gas line hose. If it is evident there is excessive abrasion or wear, or the hose is cut, the hose must be replaced prior to the appliance being used.

INSTALLING A GAS CYLINDER

1. From the side of the cart (A), place foot ring of 9 kg (20 lbs) tank onto the gas tank hook (B) and bracket (C). Make sure the tank valve is in OFF position. Ensure the tank is completely upright, as it is unsafe to operate the griddle if the gas tank is not installed properly.
   
   
   

2. Ensure the regulator valve on the griddle is completely closed by turning the knob clockwise to the OFF position.

3. Remove the protective caps from the regulator valve opening and the top of the gas cylinder. Save the caps.

4. Insert the gas cylinder valve into the threaded opening of the regulator valve. Turn the quick coupling nut clockwise until firm. Hand-tighten only (D).
   

5. Gas cylinder is now installed.

The outdoor griddle, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes with the National Electrical Code ANSI/NFPA 70, or Canadian Electrical Code, CSA C22.1.

1. Do not store a spare LP gas tank under or near this appliance.
2. Never fill the tank beyond 80 percent full.
3. If the information in 1) and 2) is not followed exactly a fire causing death or serious injury may occur.
4. Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap on the cylinder valve outlet that is provided with the cylinder valve. Other types of caps or plugs may result in leakage of propane.
5. The LP gas tank used must have a collar to protect the tank valve.
6. Always keep the LP cylinder at 90 degrees (upright) orientation to provide vapor withdrawal.

DISCONNECTING A GAS CYLINDER

1. Ensure the regulator valve on the griddle is completely closed by turning the knob clockwise to the OFF position.
2. Turn the quick coupling nut counter-clockwise (by hand) to disconnect from the regulator valve opening. Replace the protective caps on the regulator valve opening and the top of the gas cylinder for storage (if not empty).

NOTE: If storing the griddle indoors, leave the gas cylinder outdoors.

WARNING: Do not fold up or transport griddle with gas cylinder attached. The cylinder may loosen off the valve and cause a gas leak, possibly resulting in an explosion, fire, or severe bodily harm. Disconnect gas cylinder first before travel or storage.

OPERATING INSTRUCTIONS

GRIDDLE ENVIRONMENT

1. WHERE TO SET-UP THE GRIDDLE
   With all outdoor appliances, outside weather conditions play a big part in the performance of your griddle and the cooking time needed to perfect your meals. All Pit Boss® Grills units should keep a minimum clearance of 1,270 mm (50 inches) from combustible constructions, and this clearance must be maintained while the griddle is operational. This clearance must be maintained while the griddle is operational. This appliance must not be placed under overhead combustible ceiling or overhang. Keep your griddle in an area clear from combustible materials, or other flammable vapors and liquids.

2. COLD WEATHER COOKING
   As it becomes cooler outside, that does not mean that grilling season is over! The crisp cool air and heavenly aroma of grilled foods will help cure your winter blues. Follow these suggestions on how to enjoy your griddle throughout the cooler months:
   • Organize – Get everything you require ready in the kitchen before you head outdoors. During the winter, move your griddle to an area that is out of the wind and direct cold. Check local bylaws regarding the proximity of your griddle in relation to your home and/or other structures. Put everything you need on a tray, bundle up tight, and get it done!
   • To help keep track of the outside temperature, place an outdoor thermometer close to your cooking area. Keep a log or history of what you cooked, the outdoor temperature, and the cooking time. This will help later down the road to help you determine what to cook and how long it will take.
   • Have a heated platter or a dish cover ready to keep your food warm while making the trip back inside.

3. HOT WEATHER COOKING
   As it becomes warmer outdoors, the cooking time will decrease. Follow these few suggestions on how to enjoy your griddle throughout the hot months:
   • Adjust your cooking temperatures downward. This helps to avoid unwanted flare-ups.
   • Use a meat thermometer to determine the internal temperature of your foods. This helps in preventing your meat from over cooking and drying out.
   • You can keep foods hot by wrapping them in foil, and placing them in an insulated cooler. Stuff crumpled up newspaper around the foil and this will keep food hot for 3 to 4 hours.

PREPARATION FOR USE – LEAK

A leak test is used to determine the integrity of a seal. Before using your gas griddle, perform a leak test on  the connection between the regulator and the gas cylinder to reduce the risk of serious bodily injury or death from fire or explosion. A leak test should be performed a minimum of once a season, as well as:

• before lighting your griddle for the first time,
• every time the gas cylinder has been changed,
• after travel, especially over rough or bumpy roads,
• after a prolonged period of storage or non-use.

HOW TO PERFORM A LEAK TEST

Supplies Required:

• Bowl (empty, clean)
• Paint Brush (clean)
• Dish Washing Liquid
• Water

Procedure:

1. Position the griddle in a well-ventilated area. Ensure the griddle is cool to the touch, and not in use. Verify that the regulator value is turned to the OFF position and that the gas cylinder is tightened securely to the regulator.
   IMPORTANT: Ensure there is no open flame or smokers nearby.

2. Mix a solution of one part of water with one part of dish washing liquid in a bowl. The solution will make bubble, as it will be concentrated.

3. Use a paint brush to apply the solution onto the seal between the regulator and the gas cylinder. Visually inspect for streams of bubbles coming from a defect or break in the seal.

NOTE: If a leak appears, repeat gas cylinder installation procedure, but do not over-tighten. Hand-tighten only. Repeat leak test after re-installation to ensure seal is secure.

IMPORTANT: Do not use the gas griddle if you detect a gas leak that cannot be corrected by using the leak test procedure. Contact your local Fire Department or Customer Care for alternative measures of testing to ensure proper precaution.

FIRST USE – GRIDDLE BURN-OFF

Before using your griddle for the first time with food, it is important to complete a burn-off. Start the griddle and operate for a minimum of 15 minutes on HIGH to burn-off the unit. This will “heat clean” the internal components, dissipate odors, and rid it of any foreign matter.

LIGHTING PROCEDURE

1. Verify that all control knobs are turned to the “O” OFF position.
2. Connect LP gas cylinder as per instructions. Turn LP gas tank valve to OPEN.
3. Note the indicator marker on the control knob. Push and hold down the control knob on the griddle and turn 90 degrees (or 1/4) counter-clockwise SLOWLY (2 to 3 seconds) to LO LO (Ignition/HIGH). You should hear a “click” sound to indicate a spark from the igniter, and look for flame to ensure the burner is lit. If it does not, repeat up to three times.
4. If ignition does not occur in 5 seconds, turn the control knob to “O” OFF, wait 5 minutes and repeat lighting procedure. If the above points do not work, follow Manual   Lighting Procedure instructions.
5. After the burner has caught fire, you are ready to enjoy your griddle at your desired temperature!

If the burner goes out during operation, turn the control knobs to the OFF position. Wait five minutes before attempting to relight to allow any accumulated gas to dissipate.

IGNITER FAILURE PROCEDURE
If for any reason your igniter fails after three of four attempts, check the following steps, or start your griddle using the manual method.

1. Ensure the control knobs are turned to the OFF position. Allow any accumulated gas to dissipate.

2. After five minutes, check the following:
   • Visually confirm that the igniter is working by pushing the igniter button and looking at the igniter tip for a spark. If no spark, replace the battery in the lighter button or adjust the distance between the igniter (electrode) tip and burner to 4.5 mm (3/16 in).
   • Visually confirm that the burner tube and portholes are not obstructed. If blocked, follow Care & Maintenance instructions.

3. If the above points do not work, follow Troubleshooting instructions.

MANUAL LIGHTING PROCEDURE

1. Verify that the control knob is turned to the OFF position.

2. Connect LP gas cylinder as per instructions. Turn LP gas tank valve to OPEN.

3. Note the indicator marker on the control knob. Push in the regulator knob and turn 90 degrees (or 1/4) counter-clockwise to HIGH.

4. Quickly and carefully, use a lit match secured with the lighting rod (included with the griddle) to light burners. Access the burners through the hot plate. Position lit match near side of burner. Do not attempt to light another area of the burner. This can cause injury.
   NOTE: Do not use spirit, lighter-fluid, or kerosene for lighting or refreshing a fire in your griddle.

5. After the burner has caught fire, you are ready to enjoy your griddle at your desired temperature!

SHUTTING OFF YOUR GRIDDLE

1. When finished cooking, turn LP gas tank valve to the CLOSED position, and allow the regulator knob to pop out. This safety feature locks the regulator knob to ensure that the gas is no longer flowing.

2. Turn control knobs to the OFF position.
   NOTE: A “poof” sound is normal as the last of the LP gas is burned.

3. Disconnect LP gas tank by following the Disconnect LP Gas Tank instructions.
   WARNING: Allow the griddle to cool completely, and remove the gas cylinder, before moving, travel, or for storage.

COLLAPSING FOR STORAGE

Your griddle can quickly and easily be collapsed for storage and easy transportation. To fold down and securely store your griddle, simply follow the assembly instructions in reverse or the following summary:

IMPORTANT: Always ensure the griddle is completely cooled, disconnected from a gas supply, and that the grease cup is removed.

1. Remove the Grease Cup (A) and carefully lift the Hot Plate off of the Firebox (B). This is easier using two people, but not necessary.
   

2. Lay the Firebox on its side with the control knobs on the top. Remove the two bolts from the Bottom Shelf. Remove the Bottom Shelf (C).
   

3. Loosen the four bolts, one on each leg (D). Pull back on the locking system pins to fold-in the cart legs to collapse the cart (E).
   
   
   NOTE: To not misplace, re-install the bolts into the cart and Bottom Shelf once the cart is completely collapsed.

4. Carefully raise the unit into an upright position with the wheels on the bottom. Replace the Hot Plate onto the top of the Firebox. Place the Bottom Shelf over the Hot Plate (F).
   

5. Close the side shelves and lock the front latch (G).
   

CARE & MAINTENANCE

CHECKING THE GAS LEVEL

To check the amount of fuel in the LP gas cylinder, the griddle must be in operation. Place your hand at the top of the tank and slowly move down the side until the tank feels cool to the touch. This will indicate the approximate amount of gas in your tank; if ¾ empty, replace with full tank.

IMPORTANT: Do not use charcoal briquettes or any flammable material with your griddle. Use of such material will void your warranty and may lead to a fire, explosion, and bodily harm.

CLEANING FREQUENCY

Any Pit Boss® unit will give you many years of flavorful service with minimum cleaning. Follow these cleaning and maintenance tips to service your griddle:

Burner Components

• Clean the burner whenever heavy build-up is found, to ensure that there are no signs of blockage (debris, insects) on the burner tube or in the burner portholes (A). After periods of storage, spiders or small insects can build nests, webs, and lay eggs in the burner tube, obstructing the flow of gas to the burner. If storing the griddle or before an extended period of non-use, remove the burner and wrap with aluminum foil to reduce the risk of insects entering the burner holes.
  

• The burner has been preset for optimal flame performance. A blue flame, possibly with a small yellow tip, is the result of the optimal air and gas mixture. If flames are excessively yellow, orange, or irregular, clean the oil and food deposits on the burner surface and the burner portholes to increase airflow.

Griddle Surface

• Your griddle comes preseasoned from the factory, but it is important to clean and season your griddle after each use to prevent rust, extend the life of your griddle, and create a non-stick cooking surface. The seasoning of your griddle is a continuous process that must be repeated over the life of your griddle to ensure the best cooking experience and longest life for your griddle.
  1. Clean the griddle after each use, using a spatula or scraper to remove all food and debris from cooking surface.
  2. Liberally apply an even coat of cooking oil to the cooking surface. Vegetable, olive, peanut, coconut, and sesame oils are all suitable for seasoning your griddle.
  3. Turn the griddle off, and allow to cool in a cool, dry location.

• Remove any food or build-up from the cooking surface. Best practice is to do this while it is still warm from a previous cook (B). Grease fires are caused by too much fallen debris on the cooking components of the griddle. Clean the inside of your griddle on a consistent basis. In the event you experience a grease fire, carefully remove the food, turn the griddle off. Lightly sprinkle baking soda, if available.
  

• Check your grease cup often, and clean out as necessary. Keep in mind the type of foods that are cooked (C).
  

• Use a griddle cover to protect your griddle for complete protection! A cover is your best protection against weather and outside pollutants. When not in use or for long-term storage, keep the unit under a cover in a garage or shed, with the gas cylinder removed (must be stored outdoors).

GRIDDLE CARE CHEAT SHEET

season with cooking oil
Grease Cup| After each use| Empty, scrub pad & soapy water
Burn tube, air inlets| Every 5-6 Griddle Sessions| Dust, scrub pad & soapy water
Burners| Every 5-6 Griddle Sessions| Scrub pad & soapy water

TIPS & TECHNIQUES

Follow these helpful tips and techniques, passed on from Pit Boss® owners, our staff, and customers just like you, to become more familiar with your griddle:

1. FOOD SAFETY
   • Use different platters and utensils for the cooked meat than the ones you used to prepare or transport the raw meat out to the griddle. This will prevent cross contamination of bacteria. Each marinade or sauce should have its own utensil.
   • Keep hot foods hot (above 60ºC / 140ºF), and keep cold foods cold (below 3ºC / 37ºF). Cooked foods should not be left out in the heat for more than an hour. Do not leave hot foods out of refrigeration for more than two hours.
   • A marinade should never be saved to use at a later time. If you are going to use it to serve with your meat, be sure to bring it to a boil before serving.
   • Defrost and marinade meats by refrigeration. Do not thaw meat at room temperature or on a counter top. Bacteria can grow and multiply rapidly in warm, moist foods. Wash hands thoroughly with hot, soapy water before starting any meal preparation and after handling fresh meat, fish, and poultry.

2. COOKING PREPARATION
   • Be prepared, or Mise en Place. This refers to preparing the cooking recipe, fuel, accessories, utensils, and all ingredients you require at griddle side before you start cooking. Also, read the entire recipe, start to finish, before lighting the griddle.
   • A BBQ floor mat is very useful. Due to food handling accidents and cooking spatter, a BBQ floor mat would protect a deck, patio, or stone platform from the possibility of grease stains or accidental spills.

3. GRILLING TIPS AND TECHNIQUES
   • Always use a meat thermometer to determine the internal temperature of the foods you are cooking. It’s a good idea to put cooked food onto a heated platter, keeping the food warm. Red meats, such as steak and roasts, benefit from resting for several minutes before serving. It allows the juices that were driven to the surface by heat to ease back to the center of the meat, adding more flavor.
   • Sugar-based sauces are best applied near the end of cooking to prevent burning and flare-ups.
   • Use a set of long-handled tongs for turning meats, and a spatula for turning burgers and fish. Using a piercing utensil, such as a fork, will prick the meat and allow the juices to escape.

Accessories are available for purchase separately. Contact your local authorized Pit Boss® dealer or visit www.pitboss-grills.com.

TROUBLESHOOTING

Proper cleaning and maintenance will prevent common operational problems. When your griddle is operating poorly, or on a less frequent basis, the following troubleshooting tips may be helpful. For FAQ, please visit www.pitbossgrills.com. You may also contact your local dealer or Customer Care for assistance.

WARNING: Always ensure the griddle is completely cooled to avoid injury.

assistance or a replacement part.
No igniter spark on electrode| Adjust the electrode. Contact Customer Service for assistance or a replacement part.
No gas supplied| Check the regulator valve. Check connection for leak.
Grease Fire / Frequent Flare-Ups| Grilling fatty meats| Griddle fatty meats when the cooking surface is cold, and the knobs are on the “LOW” setting.
Cooking temperature| Attempt cooking at a lower temperature. Grease does have a flash point. Keep the temperature under 176°C / 350°F when cooking highly greasy food.
Water sprayed on gas flames| Do not spray water on gas flames.
Burner blows out| No Gas Flow

Gusting Or High Winds

| Check gas fuel connection, and ensure it is open. Replace gas cylinder if empty.

Turn front of griddle away from wind or increase flame height.

Low heat on “HIGH”| Ports blocked

Gas tank empty

| Clear ports of any obstructions.

Refill the gas tank.

Gas Leakage| Improper Installation| Turn the regulator knob to the OFF position, and allow the regulator knob to pop out. Remove the gas cylinder. Re-install and tighten. Perform leak test to ensure proper seal. Replace gas cylinder if damaged.
Seal Failure| Gas cylinder has corroded, rusted, or has been mishandled. Replace gas cylinder.
Regulator Failure| Regulator needs to be replaced. Contact Customer Service for a replacement part.
Burner Flames Are Yellow Or Orange| Poor Air Flow

Burner Obstruction

| Check burner tube and burner ports for spider webs or other obstructions. Follow Care and Maintenance instructions to clean the burner tube.
Grease Cup Is Full, Spilling| Empty grease cup and re-install. Follow Care and Maintenance instructions.
Regulator Valve Is Off| Check the regulator valve connection to the gas cylinder. Remove, then reinstall. Perform leak test.
Burner Is Dirty| Turn regulator knob to HIGH for five minutes, and burn-off the unit. Follow
Care and Maintenance instructions.
|

HAVE A QUESTION?

Check out some common FAQs online or Live Chat with Customer Care.

|
---|---|---

WARRANTY

TERMS & CONDITIONS

Pit Boss® Grills (“Pit Boss®”), manufactured by Dansons, carries a 2 year warranty against defects and workmanship on all parts and a 2 year warranty on electrical components of this product. Dansons warrants that all parts to be free of defects in material and workmanship, under normal use and conditions, for the length of use and ownership by the original purchaser

There is no other or additional warranty applicable to this product.
This warranty does not apply:

• if unable to provide proof of the purchase or after the warranty has expired.
• to damages or defects from wear and tear, such as scratches, dents, dings, chips or minor cosmetic cracks. These aesthetic changes of the product do not affect its performance.
• if your product has not been installed, operated, cleaned and maintained in strict accordance with the accompanied product manual. The warranty does not cover damage or breakage due to misuse, improper handling or custom modifications.
• to rust or oxidization, unless there is loss of structural integrity on the griddle component. Even by utilizing materials that resist rust, the protective coatings can be compromised by various substances and conditions beyond control of the manufacturer. High temperatures, excessive humidity, chlorine, industrial fumes, fertilizers, lawn pesticides and salt are some of the substances that can affect metal coatings.
• to damages or defects occurring during commercial use, rental use, or any use for which the product is not intended.
• to damages or defects exceeding the cost of the product.
• to damages or defects caused by service or repair of the product by an unauthorized dealer of Pit Boss®.

During the term of the warranty, the Dansons obliges to furnishing a replacement for defective and/or failed components and will not charge for repair or replacement for parts returned, freight prepaid, should the part(s) are found to be defective upon examination.

Dansons does not accept responsibility, legal or otherwise, for the incidental or consequential damage to the property or persons resulting from the use of this product, during or after the warranty period. All warranties by manufacturer are set forth herein and no claim shall be made against manufacturer on any warranty or representation. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations of implied warranties, so the limitations or exclusions set forth in this limited warranty may not apply to you. This limited warranty gives you specific legal rights and you may have other rights, which vary from state to state.

REGISTER YOUR GRIDDLE

Register your product in less than a minute and gain quick and easy access to an impressive collection of cooking knowledge.

Your registration (proof of purchase) will ensure you receive the best warranty service with your product. In the unlikely event there are safety concerns, it is our fast-track way of notifying you.

|
---|---

CUSTOMER CARE

If you have any questions or concerns about your product, our helpful Customer Care team are eager to assist you. Please have your registration information ready before contacting Customer Care.

|
---|---

CUSTOMER SUPPORT

PIT BOSS® GRILLS 16
WWW.PITBOSS-GRILLS.COM

References

• P65Warnings.ca.gov
• Home | Pit Boss® Grills

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>