SmallRig 3487LEQI Forevala W60 Wireless Microphone User Manual

Foreplay W60
Wireless Microphone
User Manual

3487LEQI Foreplay W60 Wireless Microphone

Preface
‘Thank you for purchasing Small Rigs products
Important Notes
Please read this User Manual careful.
Do not use the product in water because it is not dust or water proof.
Do not let the product allot the ground, be hit or suffered violent impact
Do not exert pressure on its LCD screen because over pressure will cause permanent damage to the screen.
Do not use the product n the completely closed environment, or it may lead to ise of internal temperature, which causes product Failure, ignition or other accident.
Do not eave the product in excessive heat, high temperatures can cause the product to malfunction.
Do not place the product n a place where there are corrosive chemical to protect the product from corrosion,corrosion may cause the product to malfunction.
Do not place the product nearby any combustible or volatile solution,or it may cause a ire disaster or smog, Be sure to power the product off when iris not in use.
Use only microfiber and dry cloth for cleaning the product
Never remove the non-detachable lithium battery without permission.
When the battery is ot in use for along time, please charge and discharge the battery each 6-month, and provide t with approximately 60% of the electric quantity prolong fetime.
Since there are some hazardous substances in the battery, please dono discard . Instead, dispose of the product that is damaged o will never be used according o the waste management measures.
Note: To prolong the lifetime, please minimize the use of the product while charging.
Warning
Please do not disassemble the product.If you suspect any problem with the product,please contact the purchasing platform and apply for after sales treatment.
Standard Use of the Equipment
“The standard use of the Small Rig Foreplay W60 wireless microphone includes
Read this manual carefully, especially the “Important Notes™ section.
Use and store the product under the working conditions specified in this manual.

In the Box

Product Details

Transmitter

1. Microphone: built-in condenser microphone
2. 3.5mm port: TR external microphone jack
3. USB-C port: 5V charging port
4. Display: interactive LCD display
5. Powerboat: short presto mute  on,long presupposition  and off
6. Pairing key: short press low cut on, on press  to pair

Transmitter screen

1. Mute / Microphone works normally
2. Signal intensity
3. Low cut function enabled
4. Transmitter battery power
5. Microphone audio bar of channel A/ B

Operations

1. Switch button:long press to power on / off. “Small” logo appears on the LCD screen after power on. n power on mode,  short press to enter mute mode, and short press again to enter normal mode.
2. Low cut function: short press the low-cut button to tum on/ off the low-cut function. When the low cut function is tured on, the LCD screen displays the low-cut symbol,Manual pairing: long press the “low cut / pairing” button to enter pairing mode. When rebooting TX and entering pairing mode, the signal display symbol wil be dynamically displayed until paired with the receiver  ( RX)
3. Charging function: the TX can be charged by connecting the cable through the storage case o directly though the USB-C charging cable, with charging dynamics displayed on the LCD screen while charging

Receiver

1. Knob 1: volume up or down for receiver A (press knob 1 and knob 2 simultaneously to pair)
2. Display: LCD display
3. Knob 2: volume up or down for receiver B (press knob 1 and knob 2 simultaneously to pair)
4. Power button: receiver on / off
5. 3.5mm port 2: TRS / TRRS headphone monitor jack
6. 3.5mm port 1: TRS audio output port
7. USB-C port: 5V charging port

Receiver screen

1. Stereo: Stereo sound channel / Mono: Mono sound channel
2. Receiver battery capacity
3. Microphone audio bar of channel A / Microphone audio bar of channel B
4. Channel A output volume / Channel B output volume

Operations

1. Switch button: long press to power on / off “Small Rig” logo appears on the LCD screen after power on. In power on mode, for each short press, the audio output switches between mono/stereo, and the display will show “Mond / “Ste red”
2. Gain adjustment: through the group A volume adjustment knob, rotate it clockwise to increase the volume, and vice versa to reduce the volume. Through group B volume adjustment knob, rotate it clockwise o increase the volume, and vice versa to reduce the volume. The gain is displayed in three colors, in which ‘green means below -12d8, yellow means -12dB ~ 0B, and red means above 0dB.
3. Manual paining: the volume adjustment button on the RX is used as a pairing button when pressing. When the volume buttons of groups A and B are pressed simultaneously, the receiver enters the pairing mode (for TX,long press the pairing button). At the same time, the group information is flashing on the display, until it is paired with the transmitter (TX ) – After connecting to the transmitter, the group information i of reverse display, otherwise hollow display, in biack font. In pairing mode, press any button to exit
4. Charging function: the RX can be charged by connecting the cable through the storage case or directly through the USB-C charging cable, with charging dynamics displayed on the LCD screen while charging.

Storage case

1. Charging: red display when connected o the power supply to charge RX / TX, and green display when RX / TX is fully charged.
2. Port: with USB-C charging port, and built-in USB-A charging cable at the bottom of the storage case.

Operating Instructions

Transmitter
Mount the transmitter to the collar via the back clp 50 that the boot-n microphone pins in the direction of the audio source.
(Note:In the process of use, for better concealment, itis recommended that the back clip is fixed towards the outside for use)
Use an textual microphone
Plug the 3.5mm TRS microphone input cable into the transmitter’s 3.5mm TRS external microphone jack. Clip the transmitter to your et via the back pic then clip the lavaliere microphone on the other entourage collar
(Note: When using an external microphone, the builtin microphone will automatically urn off)
Receiver
Method for using with the camera
Clip the receiver to the cameras cold shoe mount via the back clip. Connect the receiver o the camera via 3.5mim T RS-YRS cable. Plug the headphones into the headphone monitor hole for monitoring

Method for using with the mobile phone
Clip the receiver to the cold shoe mount via the back cpl.
Connect the receiver to the mobile phone via 3.5mm T RS-ERRS cable, and note that the access to the receiver audio output jack is 3.5mm YRS plug, access to the mobile phone end is 3.5mm “ERRS plug. Plug the headphones into the headphone monitor jack for monitoring.

Frequency response

Directionality

Specifications and parameters

Transmitter

Wireless band| 2402 — 2480MHz
Microphone directionality| Omani-directional
Sound delay| <15ms
External input port| 3.5mm YRS microphone input
Battery specification| 450mAh 3.7V 1.665Wh
Endurance time| 8h
Display| LCD display
Operating distance| 100m (without obstacles)
Charging time| 1h
Input voltage| 5V
Receiver

Wireless band| 2402 — 2480MHz
RF sensitivity| -81dB
Sound delay| <15ms
Output port 1| 3.5mm TRS audio output
Output port 2| 3.5mm TRS / TRRS headphone output
Battery specification| 630mAh 3.7V 2.331Wh
Endurance time| 8h
Display| LCD display
Input voltage| 5V
Number of audio channels| 2 channels
Charging time| 1.5h
Operating distance| 100m (without obstacles)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>