GE Lighting Cync Smart LED Downlight Fixture Smart Wafer Light Installation Guide

Wafer Downlight Installation Guide
4-in & 6-in Integrated LED Recessed Fixture

Getting Started

For set up help, visit cyncsupportgelighting.com or call 1-844-302-2943

Let’s Do It

GE is a trademark of General Electric Company. Used under trademark license. Amazon, Alex°, and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Googde and other related marks and logos are trademarks of Google 11C.

Specifications

Model| Input Voltage (Vac, Hz)| Current
(mA)| Wattage
(W)
---|---|---|---
Full Color Wafer Downlight 4″ CFIXCNLR4CRVD
Full Color Wafer Downlight 6″ CFIXCNLR6CRVD
Tunable white wafer downlight 4′ CFIXCNLR4SD
Tunable white wafer downlight 6′ CFIXCNLR6SD| 120, 60
120, 60
120, 60
120, 60| 110
130
110
130| 13
16
13
16

Dimming Capability

NOT FOR USE WITH DIMMER SWITCHES. Compatible with only CYNC smart dimmers that provide dimming at the switch or through the CYNC App.
Before you begin : Read these instructions completely and carefully.
WARNING: RISK OF ELECTRIC SHOCK
Risk of fire or electric shock. Installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt installation. Minimum 90°C Conductors, if uncertain contact a qualified electrician.

• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• These products are intended to be used in dry, damp, or wet locations.
• IC rated for direct contact with insulation.

Prepare Electrical Wiring

ELECTRICAL REQUIREMENTS
The LED fixture must be supplied with 120VAC 60Hz
GROUNDING INSTRUCTIONS
The grounding and bonding of the overall system shall be done in accordance with National Electric Code (NEC) Article 410 and local codes.
Compatible Trim Accessory (sold separately)

CFIXCNLIRLICRVD
CFIXCNLRLISD| CANACOLIBNRO/ CANACOL1OBRO/ CANACOLIBNSQ/
CANACOLIOBSQ/ CANACOLM/HSQ/ CANACOLANHWW
CFIXCNLR6CRVD
CFIXCNLR6SD| CANACO6BNRO/ CANAC060BRO/ CANACO6BNSQ/
CANACO6OBSQ/ CANACO6WHSQ/ CANACO6WHWW

You Got This!
And we’re here to help. For in-depth instructional videos and a guided tour through the installation, go to: cyncsupportgelighting.com or call 1-844-302-2943

Scan here for videos 8r guided installation steps.

BEFORE YOU DO ANYTHING: Step 1
Turn Off The Power!
Turn off power sauce at the main circuit breaker or fuse box.
Step 2
Mark the Location on the Ceiling & Cut the Hole

1.  Determine the position of your downlight
   • Maximum distance from junction box to the downlight is 24 inches
   • Location must be within range of 2.4GHz 1M-Fi to enoble smart control.
   • If retrofitting, find path of access above the ceiling.

2. Once determined use the hole template to truce the hole size. Cut the hole using a drywall or hole saw.
   • 4 inch wofer requires a 4-1/4 inch hole
   • 6 inch wafer requires a 6-1/4 inch hole
   Note: Reference the guide included with the Installation Mounting Template if using for installation. Instollation mounting template sold separately. Not necessary for installation.

Step 3 Use the Wire Connectors to Wire the Wafer Downlight

1. Open the top of the junction box and locate the three quick connectors inside.

2. Connect the wires inside the junction box to the provided quick connector.
   • Insert the black wire into the left hole of the first quick connector.
   • Insert the white wire into the left hole of the second quick connector.
   • Insert the green wire into the left hole of the third quick connector.

3. Route the wires from the switch through the wire notch on side of the junction box.

4. Connect the wires to the quick connectors by inserting the wire into the middle hole. Using the quick connectors
   • Connect the block wire to the black wire.
   • Connect the white wire to the white wire.
   • Connect the green or bore copper wire to the green wire.

5. Gently pull on the wires to make sure they ore properly connected.

6. Tuck the wires and connectors inside the junction box.

7. Close the junction box.

Alternative Installation

1. Remove knockouts using o hammer and screwdriver, mount the stroin relief (sold separately) and route the wires through.
2. Follow the wiring instructions in Step 3 to complete wiring instollotion.

Step 4 Place Junction Box in the Ceiling & Install the Fixture

1. Place the junction box in the ceiling through the hole.
   Note: While it is not necessary to mount this fixture to a joist, be sure to follow your building code requirements, as well as national and local electric code for mounting.

2. Connect the light to junction box using the connector.

3. Screw the connector together to complete the connection.

Step 5 Complete Setup

1. Hold the spring clips against the fixture and gently guide into the ceiling until the clips snap into place.
2. Complete setup in the Cync App.

Congratulations!
You’ve completed the Wafer Downlight installation.

Enable Your Voice Assistant
Connect to your Amazon Atexa or Google Assistant devices in the CYNC App
Then try this…
Alexcr, turn off the living room. Hey Google, turn on the lights.
Alexq, turn on the bedroom. Hey Google, good morning.
Alexcs set kitchen to 50% Hey Google, I’m leaving.

Additional Information and Warnings

FCC Compliance Statement Compliance Notice:
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Port 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment Into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. The device must not be co-located or operating In conjunction with any other antenna or transmitter. This device complies with part 15 of FCC rules. Operation Is subject to the following two conditions (I) this device may not cause harmful interference, and (2) this device must accept any interference received, Including interference that may cause undesired operation.

RF Exposure Information:
Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons

IC Stahment
This device complies with RSS247 of Industry Canada.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment This transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter.
Like your new Wafer Downlight?
Share your experienc e!
Leave a review where you purchased the product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>