StarTech com RK319WALLV 19 Inch Vertical Wall Mount Rack Bracket User Guide

: June 10, 2024
: StarTech com

Table of Contents

Product IDs
Product Diagram
Package Contents
Requirements
Installation
Regulatory Compliance
Warranty Information
Limitation of Liability
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Quick-Start Guide
19in Vertical Wall Mount Rack Bracket

Product IDs

RK119WALLV / RK119WALLV2
RK219WALLV
RK319WALLV / RK319WALLV2
RK419WALLV / RK419WALLV2
RK519WALLV
RK619WALLV

Product Diagram

StarTech com RK319WALLV 19 Inch Vertical Wall Mount Rack Bracket - Product
Diagram

*Product may vary from image

Component	Function
1. Mounting Rails	• Features Square Cage Nut Holes to mount the equipment
2. Wall Bracket	• Mounting Holes along the Wall Bracket are used to Fasten

it to a Wall

Package Contents

Wall-Mount Bracket x 1
Wood Screws x 6
Quick-Start Guide x 1

Product ID	MS Square Cage Nuts Quantity	MS Screws Quantity
RK119WALLV / RK119WALLV2	x 4	x 4
RK219WALLV	x 8	x 8
RK319WALLV / RK319WALLV2	x 12	x 12
RK419WALLV / RK419WALLV2	x 16	x 16
RK519WALLV	x 16	x 16
RK619WALLV	x 16	x 16

Requirements

For the latest manuals, product information, technical specifications, and declarations of conformance, please visit:
www.StarTech.com/RK119WALLV
www.StarTech.com/RK219WALLV
www.StarTech.com/RK319WALLV
www.StarTech.com/RK419WALLV
www.StarTech.com/RK519WALLV
www.StarTech.com/RK619WALLV
www.StarTech.com/RK119WALLV2
www.StarTech.com/RK319WALLV2
www.StarTech.com/RK419WALLV2

Appropriate mounting hardware for the wall or surface type
Phillips head screwdriver
Cage nut tool (Optional)

Warnings!
Read the entire Quick-Start Guide and ensure the instructions are fully understood before assembling and/or using this product.
Before adding equipment to this product, ensure this product has been properly mounted.
Never operate this product if parts are missing or damaged.
The mounting hardware included with this product might not be adequate for some wall or mounting structures. If lacking the necessary expertise to mount this product, contact a construction professional to install the Wall Rack Bracket or to provide specific mounting instructions for the wall structure.
Ensure the weight of the equipment does not exceed the weight capacity of this product.
If the weight capacity is exceeded, personal injury or damage to the equipment are possibilities. These products can support the following weight:

RK119WALLV: Rev 01 to 02 – Up to 125 lbs / 56kg; Rev 03 or above – Up to 130 lbs / 59kg
RK119WALLV2: Up to 130 lbs / 59kg
RK219WALLV: Up to 125 lbs / 56kg
RK319WALLV: Rev 01 to 02 – Up to 125 lbs / 56kg; Rev 03 or above – Up to 150 lbs / 68kg
RK319WALLV2: Up to 150 lbs / 68kg
RK419WALLV: Rev 01 to 02 – Up to 125 lbs / 56kg; Rev 03 or above – Up to 180 lbs / 81kg
RK419WALLV2: Up to 180 lbs / 81kg
RK519WALLV: Up to 198 lbs / 90kg
RK619WALLV: Up to 200 lbs / 90kg

Ensure the type of wall structure and mounting hardware will properly support the mounted equipment. Failure to do so might result in personal injury and/or equipment damage. The wall or mounting structure should be capable of supporting at least four times the weight of the mounted equipment.

Installation

Mount the Rack Bracket
The mounting holes are spaced 16 inches (2 inner holes) and 18.8 inches (4 outer holes) apart. Test fit the Rack Bracket on the surface to ensure proper fit on the designated
location.

Mark the Mounting Points (x6) using the Mounting Holes (x6) on the Wall Bracket as a Template.
Use the Wood Screws (x6) to fasten the Wall Bracket to the Mounting Surface. The included screws are for wood surfaces only.
Install the M5 Square Cage Nuts onto the desired Square Cage Nut Holes where the Equipment will be installed. Use a Cage Nut Tool if available or your preferred installation method.
Use a Phillips Head Screwdriver to install the M5 Screws and secure the Equipment onto the Mounting Rails.

Regulatory Compliance

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.

Warranty Information

This product is backed by a lifetime warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

StarTech.com Ltd.
45 Artisans Crescent London, Ontario N5V 5E9 Canada| StarTech.com LLP
4490 South Hamilton Road
Groveport, Ohio 43125 U.S.A.| StarTech.com Ltd.
Unit B, Pinnacle 15 Gower ton Road Backfills, Northampton
NN4 7BW United Kingdom| StarTech.com Ltd.
Sirius reef 17-27
2132 WT Hoofddorp
The Netherlands
---|---|---|---

FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp