Amino LIMA M3 Remote Control User Manual

Amino LIMA M3 Remote Control

Product Information

Lima M3 Remote Control

The Lima M3 remote control is a product manufactured by Amino.
It comes with a 2 AAA batteries blister inside a polybag. The remote control is designed to operate the Set-Top-Box. The device complies with Part 15 of the FCC Rules and meets general RF exposure requirements.

Product Usage Instructions

Turn On Lima M3

1. Turn ON your TV and your Set Top Box.
2. Remove your Lima M3 remote control and its batteries from the plastic bag.
3. Remove the remote’s battery lid.
4. Place the batteries on the Lima M3 remote control as indicated in the image above and replace the battery lid.
5. After inserting the batteries, wait a few seconds and the Lima M3 remote will be ready to operate the Set-Top-Box.

FCC Compliance Statements

The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To minimize interference, follow these guidelines:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for
  help.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation expuser limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Warning:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CAUTION

Risk of explosion if the battery is replaced by an incorrect type, disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion; Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; A battery subjected to extremely low air pressure that may result in an explosion or theleakage of flammable liquid or gas.

Manufacturer Information

The manufacturer nameplate is located on the battery compartment. The Lima M3 was designed in Europe and made in China on a specific year/month/day. The device has been evaluated to meet general RF exposure requirements and can be used installed and
operated with minimum distance 0mm between the radiator and your body.

Lima M3 Remote Control

Turn On Lima M3

Lima M3 remote control arrives with a 2 AAA batteries blister inside a polybag. To turn on your Lima M3 remote control, please follow the instructions below.

1. Turn ON your TV and your Set Top Box.
2. Remove your Lima M3 remote control and its batteries from the plastic bag.
3. Remove the remote’s battery lid.
4. Place the batteries on the Lima M3 remote control as indicated in the image above and replace the battery lid.
5. After inserting the batteries, wait a few seconds and the Lima M3 remote will be ready to operate the Set-Top-Box.

FCC

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televison reception, which can be determinated by turning the equipment off an on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

• This equipment complies with FCC radiation expuser limits set forth for an uncontrolled environment.
• This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
• Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CAUTION
Risk of explosion if the battery is replaced by an incorrect type, disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion; Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
Temperature range: 0º – 50ºC
Altitude: UP TO 3000 feet
MANUFACTURER
Tech4home, Lda
Rua de Fundões N.º 151, 3700-121
São João da Madeira, Portugal
NAMEPLATE LOCATED ON THE: BATTERY COMPARTMENT

T4HU2230/34kA Lima M3
DESIGNED IN EUROPE
YEAR/MONTH/DAY
MADE IN CHINA

ISED Statement

This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES3 (B)/NMB3(B).
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.

RF Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The device can be used installed and operated with minimum distance 0mm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>