XMCOSY YJ-312-4-5D Low Voltage Outdoor Spotlights User Manual

Spotlights
User Manual

INTRODUCTION

Thanks for choosing XMCOSY+ Low Voltage Outdoor Spotlights Please read the user manual carefully and keep it for future reference.
SAFETY INSTRUCTIONS
Read and follow all safety instructions before installing the low voltage outdoor spotlights.

• Sockets used to power outdoor spotlights should comply with all national and local electrical codes. If you are unsure of compliance requirements, please consult your local electrician.
• Do not use in water. Please connect power cords in deep together and tighten the protective cover. Especially for the interface at the end, please be sure to put on the protective cover. Keep the plug and socket dry.
• Please keep children away from these lights
• Keep lights away from flammables and fire sources
• Avoid placing the lights near potentially dangerous sources.
  DO NOT EXCEED RATED CAPACITY.

FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co‐located for operating in conjunction with any other antenna or transmitter.

SPECIFICATIONS

PACKAGE CONTENTS

1. Outdoor Spotlights* 4
2. Aluminum Ground Stake * 4
3. 8.2FT Light Cable* 4
4. 13.1 FT Extension Power Cable * 1
5. 36W Power Adapter* 1
6. User Manual * 1

Notes.
After unpacking, please check the product accessories.
If there are any missing or damaged accessories, please contact us as soon as possible, and our customer service team will solve it in time. service.2@xmcosy.com

ASSEMBLE

Step-1

Step -2
Connect the light cables in turn.
Notes:

1. If the connecto,s a,e not al;gned, the cola, of the spotnghts w;11 be a;tte,ent a, be ;ncons;stent w;th the cola, se!Ung ;n the APP.
2. w;thout the wate,p,oof cove,, the nght cable may subme,gei;n wate,, whkh wise cause a short d,cu;t_

Step -3
Connect the installed spotlights and the light cables in tum.

Step -4

1. Connect the extension power cable to the light cable & power adapter.
2. Plug the power adapter into the power outlet.

ADJUSTABLE SPOTLIGHTS

Rotating Head
Each spotlight can be freely usted within 105″. Rotate the handle screw to adjust the direction of the lamp head You can adjust the lighting effects you want according to the needs of the scene
Note: Beware of screws falling out. Extendable Pole
Rotating to loosen the connecto allows the pole to be extended

BUTTON FUNCTION INTRODUCTION

Button Function Introduction:

1. Long press – Enter the APP connection & network mode Long press the button for 5S, the light flashes quickly, and the product enters the distribution network mode
   (When the product is used for the first time, it will automatically enter the network distribution state after connecting to the power supply, without p「essing any
   buttons.)

2. Short press – ON/OFF & Change scene modes 8 modes(4 kinds of warm white and 4 kinds of color light) Short pressing the button, the mode changes in turn as follows
   • ON(Gorgeous)
   •Good night
   • Reading
   • Working
   • Leisure
   • Grassland
   • Colorlul
   • Dazzling
   • Gorgeous
   • OFF
   For more scene modes and functions of the product, please connect to the XMcosy APP.

SERVICE & WARRANTY

Thank you for your support of XMCOSY+I XMCOSY+ provides a regular 1-Year Warranty.
Not Satisfied?
If there is any problem with our product while using, Please Contact service.2@xmcosy.com
We will provide you with a 100% Satisfied Solution!
Satisfied?
We are glad that you didn’t encounter any problems with our low voltage outdoor spotlights.
XMCOSY+ is committed to providing better products and services. Please feel free to contact us if you have any problems with the product.
Scan to email

MAILTO:service.2@xmcosy.comsubject=Help for Spotlights&body=Order number:

APP DOWNLOAD & REGISTRATION

Step 1: Download the XMcosy App from App Store or Google Play

https://a.smart321.com/xmcosysmart

Step 2: Register

1. Enter your mob;le phone number or ema;1 address
2. Enter the ver;f;caUon code.
3. Create a password and Log ;n the App.
4. Please enable the XMcosyApp to get your Bluetooth while using the App.

DISTRIBUTION NETWORK & APP CONNECTION

Step 1: Plug – In
Plug XMCOSY+ smart outdoor spoWghts power adapter ;nto any standard outlet. Notes:

1. After power on, the light will automatically enter the connecting state (fast blinking);
2. If there is no connection after 3 minutes, the indicator lights will remain on. If you want to add a device at this time, you need to press and hold the power button on the controller for about 5 to 7 seconds until the lights blink rapidly.

Step 2: Register

1. Click the “+” in the home page upper right corner. The devices in the connecting state will be displayed at the top of the page. Click “Add”.
2. Click the device you want to add and please make sure that the network you connected is 2.4GHz.
3. Fill in your 2.4GHz network name and password, then click “Next”.
4. The product starts to connect until it is 100% completed.
5. After you edit the product name and save it, click “Done” at the top right.
   Congratulation!
   Now you can use XMcosy App to con1’ol you, spomghts

Tips:

1. The dev;ce name wm be used aga;n when pa;red to Amazon Alexa & Google Home for vo;ce control.
2. The dev;ce name ;5 suggested to cons;st of EngHsh words and Arab;c numerals, please do not use spec;a1 characters.

APP FUNCTIONS

WARM WHITE MODE & COLOR MODE
You can choose to turn on the spotlights in color light or warm white light. RGB Color Mode

• Color Wheel – SHde the color wheel up and down to adjust the color of the 1;9ht, from a b,oad spectrum of color,. Drag the button on the wheel from dght to left to adjust the oolo, temperatu,e.
• Brightness – s1;ae the b,;ghtness ba, to adjust the b,;ghtness from 1% to 100%.
• Default Color – There a,e 7 default colocs, you can cUck the ,ound colo, kons to choose a default color. Warm White Mode 0 Brightness – Slide the “b,lghtness” ba, to adjust the b,lghtness of low voltage outdoo, spotllghts from 1% to 100%, you ean freely b,lghten o, dim the lights.

* Scene Mode:
XMcosy App has a scene selection function. P『ess the scene button to enter the scene selection intertace. You can choose your favorite scenes from 32 default scenes.
You also can customize a new scene based on your favorite.

Music Sync Mode: The low voltage outdoor spotlights react in 『eal-time when your app detects the songs .
Plan: v ou can set the tome and customize favorite light mode when you fall asleep/wake up

OT HER FUNCTIONS

• Schedule: Turn on/off automatically at preset times.
• Left Time: The lights will turn off automatically afte『the countdown.
• Power-on Behavior: Power Memory mode

ALEXA PAIRING INSTRUCTION

1. Download the Amazon Alexa APP Sea,ch the keywo,ds”Amazoa Alexa” la the App Storn lo, 10S device aad la the Google Play lo, Aad,old device.
2. Sign in or register a new account
3. Pair the Amazon Alexa APP to Ama,on Echo Device (follow the Ama,oa Echo User Manual)
4. Log in your Amazon Alexa APP Important tips, please make me the “XMcosy” app, Ama,on Alexa APP “Ama,oa Echo” are coanected to the same w;-F; aetwork.
5. Enable “XMcosy” skill In Alexa APP
   a. CIiek “Skills & Games” In the MORE MENU on the Alm
   APP’s home page.b. In the popup page, input “xmcosy” in the search bar, click “XMcosy” in the search result and click ” ENABLE
   TO USE” in the popup page to enable the skills.

c. Click “Agree and link”, then “Your XMcosy account has been successfully linked”.

6. Enjoy Amazon Alexa Control
   Now with Amazon Alexa, you can take control the outdoor spotlights by asking it to change colors, turn lights on and off by using simple commands For example, using these Alexa commands below:
   “Alexa, Turn on/off {Specific light}”
   “Alexa, Set the {Specific light} to green”
   “Alexa, Set the {Specific light} to red”
   “Alexa, {Specific light} lights fifty”
   “Alexa, {Specific light} out”
   Tips: {Specific light} is the device name you named on XMcosy APP.

GOOGLE ASSISTANT PAIRING INSTRUCTION

1. Download the APP Search “Google Home” in the App Store for iOS device and in the Google Play for Android device to install.

2. Sign in or register a new account

3. Pair the Google Home APP to Google Home Device (follow the on-screen steps)

4. Link XMcosy account in set up devices a. Click the “+” icon in the upper left corner of home page, then click “set up device”.Important tlp5’please make su,e the XMcosy app, Google Home APP and Google Home devices a,e connected to the same WI-Fl netwo,
   b. Click “Works with Google”
   c. Input “XMcosy” in the search bar.
   d. In the new window, select your XMcosy account’s region, input your XMcosy account and password, then click “Next Step” and “Authorize”.
   

5. Enjoy Google Home Control Now you can take control the smart spotlights through Google Home by asking it to change colors, turn lights on and off by using simple
   commands.
   For example, using these voice commands below:
   “Google, Turn on/off {Specific light}”
   “Google, Set the {Specific light} to green”
   “Google, Set the {Specific light} to red”
   “Google, {Specific light} lights fifty”
   “Google, (Specific light} out”
   Tips: {Specific light} is the device name you named on XMcosy APP.

TROUBLESHOOTING

1. Why the colors of lights are different or can’t respond to the same color in the APP?| The cables are connected incorrectly. Please check all connectors and connect them by aligning the point. (Include the connection to thepower controller.)
2. Could the power adapter hold more than 6 lights?| No. The power adapter is 36W max and only can hold 6 lights in total. For more lights connecting, please contact XMCOSY+ Customer Service Team [service.2@xmcosy.com]
3. The lights can’t connect to the APR| 1.Please update the APP to the newest version.
2.Please turn on Bluetooth, 2.4GHz Wi-Fi, mobile data, and locations when connecting the devices.
3.Please try to connect the phone with a hots pot rather than Wi-Fi to see whether it’s the problem with Wi-Fi.
4.If the routing security level is very high or incompatible with the APP, it will cause the problem of can’t connecting to the APP. Please lower the security level of your router to make it compatible with XMcosy APP. Or send us your router model for further solutions.
4. Home network is 5GHz.| The wall penetration capability of 5.0GHz is weaker than 2.4GHz, which means that the outdoor signal of 5.0GHz is worse than 2.4GHz. Therefore, most smart devices support 2.4GHz networks or dual- frequency networks of 2.4GHz and 5.0GHz. You can log in to the management page of your router and change the SSIDs of the 2.4 GHz and 5 GHz networks to differentiate them.

CONTACT

For questions, assistance, or support, Please Contact: service.2@xmcosy.com or scan to email

MAILTO:service.2@xmcosy.comsubject=Help for Spotlights&body=Order number:

• Required Information 1. Amazon Order ID 2. Product Model NO. XMCOSY+ Customer Service Team will reply within 24 hours.
  For more info. or news about XMCOSY+, pls follow XMCOSY+ social website.
  @xmcosy+
  @xmcos”+
  **** @xmcosy
  If there is any problem with our product while using

YOU DON’T NEED TO RETURN IT TO AMAZON WE WILL PROVIDE YOU WITH A 100% SATISFIED SOLUTION

XMCOSY+ Customer Serviceservice.2@xmcosy.com
Lighting Expert,Brighten up Your Life

Documents / Resources

| XMCOSY YJ-312-4-5D Low Voltage Outdoor Spotlights [pdf] User Manual
YJ-36-4SD, YJ364SD, 2A2QEYJ-36-4SD, 2A2QEYJ364SD, YJ-312-4-5D, Low Voltage Outdoor Spotlights, YJ-312-4-5D Low Voltage Outdoor Spotlights, Outdoor Spotlights, Spotlights
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>