GRAPHITE 58G083 Cordless Washer Instruction Manual

: June 10, 2024
: GRAPHITE

Table of Contents

58G083 Cordless Washer
DETAILED SAFETY REGULATIONS
CONSTRUCTION AND APPLICATION
PREPARATION TO WORK
OPERATION / SETTINGS
CARE AND MAINTENANCE
TECHNICAL PARAMETERS
ENVIRONMENTAL PROTECTION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

58G083 Cordless Washer
Instruction Manual

58G083 Cordless Washer

https://gtxservice.pl/myjka-akumulatorowa-graphite-58g083.html

TRANSLATION OF THE ORIGINAL MANUAL

TRANSLATION OF THE ORIGINAL MANUAL RECHARGEABLE PRESSURE CLEANER
58G083
CAUTION: BEFORE USING THE APPLIANCE, READ THIS MANUAL CAREFULLY AND KEEP THIS MANUAL FOR FURTHER REFERENCE.

DETAILED SAFETY REGULATIONS

SAFETY CONDITIONS FOR PRESSURE WASHER
WARNING!
Observe the safety regulations when using the device. For your own safety and that of third parties, please read this manual before starting work. Please save this manual for future reference.
WARNING!

The washer is designed for use with cleaning agents intended for this type of device. The use of other cleaning agents may adversely affect the safety of the appliance. Do not use acids, gasoline, kerosene or other flammable liquids as a cleaning agent. Only household detergents (pH 6 ÷ 8) can be used.
Do not use the device in the vicinity of other people unless they are wearing protective clothing.
The high pressure water jet can be dangerous if not used properly. The stream must not be directed at people, animals, electrical equipment and the device itself.
Do not point the jet at yourself or others for cleaning clothes or shoes.
The high-pressure washer should not be used by children or untrained staff.
This equipment is not intended for use by people (including children) with reduced physical, sensory or mental capabilities, or people with no experience or knowledge of the equipment, unless this is done under the supervision or in accordance with the instructions for use of the equipment by persons responsible for their security.
Make sure that children do not play with the equipment.

USE

If the pressure relief switch does not trip, do not allow the washer to run for more than two minutes with the gun in the closed position. After this time, the temperature of the water in the circuit will increase and may damage the pump seals.
The washer is intended for indoor and outdoor use.
All electrically conductive parts in the workplace must be protected against water.
Never leave the device running unattended.
Turn off the power and water supply during longer breaks in use.
Do not leave the operating device unattended.
Work in potentially explosive areas is forbidden.

MAINTENANCE

Disconnect the washer from the power supply when carrying out maintenance work.
To ensure safety, use only original spare parts or parts approved by the manufacturer.
Use only high-pressure hoses, couplings and accessories recommended by the manufacturer. These are the elements that determine the safety of the device user.
Before use, check the unrolled power cord for damage or wear. Have a damaged cable replaced at the manufacturer’s service.

WARNING! Despite the inherently safe construction, the use of safety measures and additional protective measures, there is always a residual risk of injury during work.
Explanation of the pictograms used:

WARNING! Take special precautions,
Read the operating manual, observe the warnings and safety conditions contained in it,
Use personal protective equipment,
Disconnect from the power source before starting maintenance or repair activities,
Use protective clothing,
Protect against rain,
Do not direct the stream at people, animals or live installations,
Risk of injury by high pressure,
Keep the children away.

CONSTRUCTION AND APPLICATION

The pressure washer is a manual type device. The drive is a DC motor.This type of power tool is designed for washing surfaces under high pressure of water as well as for irrigation. This battery powered device is widely used in the household and garden. It is especially suitable for cleaning garden equipment and watering plants. The washer is intended solely for amateur use.
WARNING! Do not use the device contrary to its intended use.
DESCRIPTION OF GRAPHIC PAGES
The numbering below refers to the components of the device shown on the graphic pages of this manual.

Trigger lock button
The trigger
Pressure button (Eco)
Handle
The nozzle
Ventilation slots
Long lance
Nozzle
Lock ring
Short lance
Adapter with valve
Detergent spray nozzle
Detergent container
Snake
Hose quick coupler
Filter
Swimmer
Clip with a handle

There may be differences between the drawing and the product.

EQUIPMENT AND ACCESSORIES

Long lance
Nozzle
Short lance
Adapter with valve
Drawn detergent nozzle
Detergent container
Snake
Hose quick coupler
Filter
Swimmer
Clip with a handle

PREPARATION TO WORK

ASSEMBLY / REMOVAL OF THE SHORT LANCE WITH NOZZLE

Pull the locking ring (9) back, insert the tip of the nozzle (8) into the hole of the short lance (10)
(fig. A).
Release pressure on locking ring (9), check correct connection.
The removal of the nozzle takes place in the reverse order of its assembly.

WARNING! Check that the spray nozzle is properly secured.
INSTALLATION / REMOVAL AND HANDLE PISTOL LANCE

Connect the short lance (10) with the pistol grip (4) of the device by gently pressing (paying attention to the notches in the connection) and turning it 90 clockwise
(fig. B).
The long lance (7) is installed in the same way (Fig. C)
The lance is disassembled in the reverse order to its assembly.

ASSEMBLY / DISASSEMBLY OF THE SHORT AND LONG LANCE

Connect the two lances by gently pressing (paying attention to the notch in the joint) and turning by 90 in relation to each other. (fig. D).
Lances are disassembled in the reverse order to their assembly.

OPERATION / SETTINGS

CHOOSE YOUR WATER SOURCE
Connecting water from the tank

Attach the quick-connect hose (15) to the socket (5) of the appliance (fig. E).
Place the hose (14) with the filter (16) in the water tank, position the float (17) so that it remains on the water surface and secure with the clip with the handle (18). The clip with a handle (18) should be clamped on the hose (14) and hung on the wall of the tank.

WARNING! After connecting the hose, check the connection by gently pulling on the hose.
WARNING! Do not use the device with a water source that is cloudy, muddy, or corrosive. Suitable water sources: Bucket / waterbag / ditches / canals / lakes / sea (The system must be flushed completely with fresh water after use) (fig. F).
WARNING! When using open water (ditches / canals / lakes etc), make sure the filter stays far from the bottom (move the float if necessary). Always use the supplied filter hose.
WARNING! Before use, remove the air from the hose, hold (max. 1.5 m above the water source) and turn on the device. It may take about 30 seconds for water to reach the machine.
Water connection from the mains

Disconnect the hose (14) from the machine using the quick-connect hose (15).
Connect the adapter with valve (11) to the connection piece (5) of the device (fig. G).
Connect the garden hose to the nipple of the valve adapter (11) (use a standard water hose with a suitable quick coupler).

WARNING! Always use the supplied adapter with valve for mains water (drinking) water supplies. It is recommended to close the adapter valve when the device is not in use (an open valve causes water to flow out of the nozzle at the specified pressure).
WARNING! The water that has flowed through the adapter is considered unfit for drinking.
ON / OFF
WARNING! Before starting work, make sure the battery is fully charged.
Turn on – Press the trigger lock button (1) and pull the trigger (2) (Fig. H).
Turn off – Release pressure on trigger (2).
PRESSURE SETTING
The device has two pressure settings. The high pressure setting is suitable for thorough removal or cleaning, and the low pressure setting is suitable for light cleaning and watering. The device is normally set to high pressure mode. Press the pressure button (Eco) (3) to activate the low pressure mode (fig. I).
SPRAY MODE SELECTION
Spray options are selected by turning the front nozzle ring (8).
Select the spray mode according to the type of work. The 0 ‘, 15’, 25 ‘, 40’ and Jet spray settings are suitable for cleaning and the positions with the spray symbol are best for watering (fig. J).
WARNING! Do not change the spray setting after turning on the machine.
DETERGENT SPRAY ASSEMBLY
WARNING! Always use the detergent spray nozzle (12) in combination with the long lance (7) only.

Attach the long lance (7) to the device (fig. C).
Attach the detergent spray nozzle (12) to the long lance (7) connected to the machine (fig. K).
Unscrew the detergent container (13) from the detergent spray nozzle (12) and fill with the appropriate cleaning agent.
Reattach the detergent container (13) to the detergent spray nozzle (12).
Aim the detergent spray nozzle (12) at the surface to be coated with detergent and release the trigger lock button (1).
Press the trigger (2) and then the pressure button (Eco) (3) if necessary to activate the low pressure mode (the detergent placed in the tank will be sucked in and mixed with the water).
After finishing work, empty the detergent container.

WARNING! When using the water (drinking) network, make sure that the water supply is blocked (for example by the adapter valve (11)) when not using a shower. This prevents the detergent from emptying the tank.
WARNING! The pressure washer was designed to work with cleaning agents recommended by the manufacturer. The use of other cleaning agents may adversely affect the safety of the appliance. Do not use acids, gasoline, kerosene or other flammable liquids as a
cleaning agent. Only household detergents (p H 6-8) may be used.

CARE AND MAINTENANCE

WARNING! Before starting any installation, adjustment, repair or maintenance activities, remove the battery from the device.
MAINTENANCE AND STORAGE

After each use, wipe the outer casing with a cloth.
Do not use any cleaning agents or solvents as these may damage the plastic parts.
Be careful not to let water get inside the device.
Only the maintenance described in this manual may be carried out on the device. Any other activities may only be performed by an authorized service center.
It is not allowed to make any changes to the design of the device.
Keep the engine’s air vents clean.
The washer, when not in use, should be kept clean, in a dry place, out of the reach of children.
Completely drain all water from the appliance and hose before storage. Store the device and accessories in a frost-free place.

WARNING! After use in seawater, rinse the product with fresh water for proper maintenance.

Store the device with the battery removed.

All kinds of faults should be removed by the manufacturer’s authorized service.

TECHNICAL PARAMETERS

RATED DATA

58G083 cordless pressure washer

NOISE AND VIBRATION DATA

Sound power level	L WA <70 dB (A)
The value of vibration accelerations	a h <2.5 m / s 2

Information on noise and vibration
The level of noise emitted by the device is described by: the level of the emitted sound pressure L pA and the sound power level L WA (where K is the measurement uncertainty). The vibrations emitted by the device are described by the value of the vibration acceleration a h (where K is the measurement uncertainty).
The following information: emitted sound pressure level L pA, sound power level L WA and the value of vibration acceleration a h have been measured in accordance with EN 60335-1. The given vibration level a h can be used to compare devices and for a preliminary assessment of vibration exposure.
The stated vibration level is representative only for the basic use of the device. If the machine is used for different applications or with different work tools, the vibration level may change. The higher vibration level will be influenced by insufficient or too rare maintenance of the device. The reasons given above may result in an increased exposure to vibration during the entire period of operation.
To accurately estimate exposure to vibration, consider periods when the equipment is turned off or when it is turned on but not in use.
After all factors have been carefully assessed, the overall vibration exposure may be significantly lower.
In order to protect the user against the effects of vibrations, additional safety measures should be implemented, such as: periodic maintenance of the device and working tools, protection of the appropriate temperature of hands and proper organization of work.

ENVIRONMENTAL PROTECTION

****Electrical equipment must not be disposed off with household waste and, instead, should be utilized at appropriate facilities. Information on utilization can be provided by the product vendor or the local authorities. Waste electrical and electronic equipment contains substances that are not neutral to the natural environment. Equipment that is not recycled constitutes a potential hazard to the environment and to human health.

Right to introduce changes is reserved.
“Grupa Topex Spółka z ograniczoną odpowiedzialnością” Spółka komandytowa with seat in Warsaw at ul. Pograniczna 2/4 (hereinafter Grupa Topex) informs, that all copyrights to this instruction (hereinafter Instruction), including, but not limited to, text, photographies, schemes, drawings and layout of the instruction, belong to Grupa Topex exclusively and are protected by laws accordingly to Copyright and Related Rights Act of 4 February 2004 (ustawa o prawie autorskim i prawach pokrewnych, Dz. U. 2006 No 90 item 631 with later ammendments). Copying, processing, publishing, modifications for commercial purposes of the entire Instruction or its parts without written permission of Grupa Topex are strictly forbidden and may cause civil and legal liability.
EU Declaration of Conformity

Producent| Grupa Topex Sp. z o.o. Sp.k.
ul. Pograniczna 2/4, 02-285 Warszawa
---|---
Product| Battery pressure washer
Model| 58G083
Commercial name| GRAPHITE
Serial number| 00001 ÷ 99999

This declaration of conformity is issued under the sole responsibility of the manufacturer
The above listed product is in conformity with the following UE Directives:
Low Voltage Directive 2014/35/EU
EMC Directive 2014/30/EU
RoHS Directive 2011/65/EU as amended by Directive 2015/863/EU and fulfils requirements of the following Standards:
Name and address of the person who established in the Community and authorized to compile the technical file

Signed for and on behalf of:
Grupa Topex Sp. z o.o. Sp.k.
ul. Pograniczna 2/4
02-285 Warszawa
Paweł Kowalski
Pełnomocnik ds. jakości firmy GRUPA TOPEX
/GRUPA TOPEX Quality Agent/
/A GRUPA TOPEX Minőségügyi meghatalmazott képviselője/
/Splnomocnenec Kvalita TOPEX GROUP/
/Zástupce pro Kvalitu TOPEX GROUP/
Warszawa, 2020-08-28