opti Flex Water Filtration System Instructions

opti Flex Water Filtration System

Product Information

The OPTI Water Filtration System is a water filtration system designed to provide users with great tasting, alkaline water. The system is designed to fit all top load water dispensers. The filter is slow and should take about one hour to fill one gallon, and will speed up after continuous use. The system comes with a syringe that can be used to force water through the filter in case of blockage. The top basin will always have about 1/2 inch of water that does not filter through. The system should be cleaned every 2-3 months to avoid algae formation and the filter should be replaced every 3-4 months or 200 gallons/800 liters.

Product Usage Instructions

1. Wash all parts with a soft sponge and soapy water, except for the filter.
2. To activate the filter, completely submerge it in a bowl of cool water and let it soak for 4 minutes. Use the syringe to force water through the filter if it stops filtering through. Repeat compressions 5-10 times. Remove the filter from the bowl and rinse it quickly.
3. Install the float onto the bottom of the lower tank before placing the entire unit into your top load dispenser. Install the filter into the upper tank, making sure one rubber washer is used in between the filter and unit. Gently screw the filter into the hole clockwise. Do not over tighten.
4. Fill the top basin with tap water and dispose of the first filtered batch. Note: The first cycle will be a bit slow, and you may see some carbon dust in the first few fillings. This is harmless.

Remember to clean the top and bottom tank every 2-3 months to avoid algae formation and replace the filter every 3-4 months or 200 gallons/800 liters. Keep the syringe as you will need it again for your replacement filter.

QUICK TIPS

1. The filter will be slow. This is normal; it should take about one hour to fill one gallon, and will speed up after continuous use.
2. There will always be about 1/2 inch of water that does not filter through the top basin.
3. If water stops filtering through, use the syringe and force water through to clear the pores from blockage. (Step 2) To remove the filter, turn counter clock wise.

IMPORTANT

• Do NOT fill the tank with hot water or salt water.
• Do NOT use anything abrasive on the plastic parts when cleaning.

MAINTENANCE

Clean top and bottom tank every 2-3 months.
To avoid algae from forming, keep away from sunlight. Replace new filter every 3-4 months or 200 gallons/800 liters.
NEED HELP? DO YOU HAVE QUESTIONS?
SCAN THE QR CODE!

Thank you for purchasing your OPTI Water Filtration System for your water dispenser! We have designed and manufactured a water filtration system to provide you and your family, friends and co-workers with great tasting, alkaline water.
By using the OPTI Water Filtration System, not only are you avoiding the hassle of lifting heavy water bottles, but you are keeping thousands of water bottles out of the landfill, all while saving money!

• STEP 1. WASH
  Hand wash all parts with a soft sponge and soapy water (do not wash the filter).

• STEP 2. ACTIVATE
  To activate the OPTI water filter, completely submerge the filter in a bowl of cool water and let it soak for 4 minutes.

Now let’s use the syringe! Keep the filter submerged in water.
Put the tip of the syringe in the opening of the filter and create a tight seal. Grip the syringe with one hand, and with your other hand start pumping air through the syringe by moving it forcefully up and down. The goal is to see some air/water flow coming through the filter. Repeat compressions 5-10 times.
You just performed an important filter “breathing” procedure, and yes you may now call yourself a certified OPTI water doctor
Remove filter from bowl, and give it a quick rinse.
KEEP THE SYRINGE. YOU WILL NEED IT AGAIN FOR YOUR REPLACEMENT FILTER

• STEP 3. ASSEMBLE THE UNIT
  Install the float onto the bottom of the lower tank before placing the entire unit into your top load dispenser. Next, install the filter into the upper tank. Make sure one rubber washer is used in between the filter and unit. Gently screw the filter into the hole clockwise. Do not over tighten.

The OPTI Water Filtration System is designed to fit all top load water dispensers.

Note: Depending on your water dispenser, you may have to remove the bottle support collar and/or piercing valve from your dispenser in order for the filtration system to fit.

• STEP 4. FILL
  Fillthe top basin with tap water and dispose of the first filtered batch.
  Note: The first cycle will be a bit slow, and you may see some carbon dust in the first few fillings. This is harmless.
  You can now enjoy pure, high quality alkaline water!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>