SMA EVC7.4-1AC-10 EV Charger User Guide
- June 10, 2024
- SMA
Table of Contents
- SMA EVC7.4-1AC-10 EV Charger
- Product Information: SMA EV Charger 7.4/22
- Product Usage Instructions
- Legal Provisions
- Information on this Document
- Safety
- Symbols on the Product
- EU Declaration of Conformity
- UK Declaration of Conformity
- Scope of Delivery
- Mounting
- Connecting
- Commissioning
- Accessing the user interface via WLAN
- Accessing the user interface via LAN
- Configuration
- Disconnect from voltage sources
- System data
- Contact
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SMA EVC7.4-1AC-10 EV Charger
Product Information: SMA EV Charger 7.4/22
The SMA EV Charger 7.4/22 is an AC charging station designed for
unidirectional charging of a vehicle. It can be used as a stationary equipment
for indoor and outdoor use. The product comes in two variants: EVC7.4-1AC-10
and EVC22-3AC-10. The product also requires the Sunny Home Manager 2.0 to
enable intelligent charging modes. The product must be tested in fast charging
mode according to IEC 61851 before its first charging operation using a
suitable measuring device for charging stations. The product must only be used
in countries for which it is approved or released by SMA Solar
Technology AG and the grid operator.
Product Usage Instructions
- Ensure that the product is installed and commissioned by qualified persons who have the necessary skills.
- Before the first charging operation, test the product in fast charging mode according to IEC 61851 using a suitable measuring device for charging stations.
- Use the product only as stationary equipment and ensure that all components remain within their permitted operating ranges and their installation requirements at all times.
- The product is suitable for indoor and outdoor use but must not be used in industrial environments.
- Use SMA products only in accordance with the information provided in the enclosed documentation and with the locally applicable laws, regulations, standards and directives.
- Do not make any alterations to the SMA products, e.g., changes or modifications, without the express written permission of SMA Solar Technology AG. Unauthorized alterations will void guarantee and warranty claims and in most cases terminate the operating license.
eManual
Legal Provisions
The information contained in these documents is the property of SMA Solar
Technology AG. No part of this document may be reproduced, stored in a
retrieval system, or transmitted, in any form or by any means, be it
electronic, mechanical, photographic, magnetic or otherwise, without the prior
written permission of SMA Solar Technology AG. Internal reproduction used
solely for the purpose of product evaluation or other proper use is allowed
and does not require prior approval.
SMA Solar Technology AG makes no representations or warranties, express or
implied, with respect to this documentation or any of the equipment and/or
software it may describe, including (with no limitation) any implied
warranties of utility, merchantability, or fitness for any particular purpose.
All such representations or warranties are expressly disclaimed. Neither SMA
Solar Technology AG nor its distributors or dealers shall be liable for any
indirect, incidental, or consequential damages under any circumstances.
The exclusion of implied warranties may not apply in all cases under some
statutes, and thus the above exclusion may not apply.
Specifications are subject to change without notice. Every attempt has been
made to make this document complete, accurate and up-to-date. Readers are
cautioned, however, that product improvements and field usage experience may
cause SMA Solar Technology AG to make changes to these specifications without
advance notice or per contract provisions. SMA Solar Technology AG shall not
be responsible for any damages, including indirect, incidental or
consequential damages, caused by reliance on the material presented,
including, but not limited to, omissions, typographical errors, arithmetical
errors or listing errors in the content material.
SMA Warranty
You can download the current warranty conditions from the Internet at www.SMA-
Solar.com.
Software licenses
The licenses for the installed software modules (open source) can be found in
the user interface of the product.
Trademarks
All trademarks are recognized, even if not explicitly identified as such.
Missing designations do not mean that a product or brand is not a registered
trademark.
SMA Solar Technology AG
Sonnenallee 1
34266 Niestetal
Germany
Phone +49 561 9522-0
Fax +49 561 9522 100
www.SMA.de
E-mail: info@SMA.de
Status: 3/3/2022
Copyright © 2022 SMA Solar Technology AG. All rights reserved.
Information on this Document
Validity
This document is valid for:
- EVC7.4-1AC-10 (SMA EV Charger 7.4)
- EVC22-3AC-10 (SMA EV Charger 22)
Target Group
The tasks described in this document must only be performed by qualified
persons. Qualified persons must have the following skills:
- Knowledge of how the product works and is operated
- Training in how to deal with the dangers and risks associated with installing, repairing and using electrical devices and installations
- Training in the installation and commissioning of electrical devices and installations
- Knowledge of all applicable laws, standards and directives
- Knowledge of and compliance with this document and all safety information
Content and Structure of this Document
This document contains safety information as well as graphical instructions on
installing and commissioning (see page 184). Observe all information and carry
out the actions illustrated graphically in this document in the specified
order.
The latest version of this document and the comprehensive manual for
installation, commissioning, configuration and decommissioning are to be found
in PDF format and as eManual at www.SMA-Solar.com.
You will find the QR code that links to the eManual on the title page of this
document. You can also call up the eManual via the user interface of the
product.
Illustrations in this document are reduced to the essential information and
may deviate from the real product.
Levels of warning messages
The following levels of warning messages may occur when handling the product.
DANGER
Indicates a hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could result in death
or serious injury.
CAUTION
Indicates a hazardous situation which, if not avoided, could result in minor
or moderate injury.
NOTICE
Indicates a situation which, if not avoided, can result in property damage.
Symbols in the Document
Icon: Explanation
- Information that is important for a specific topic or goal, but is not safety-relevant
- Section in which the installation and commissioning process is illustrated graphically.
Safety
Intended Use
The SMA EV Charger is an AC charging station that is designed for
unidirectional charging of a vehicle. The SMA EV Charger along with the Sunny
Home Manager 2.0 makes an intelligent charging station. If the SMA EV Charger
is operated without Sunny Home Manager 2.0, the modes for intelligent charging
are not available.
The product must only be used as stationary equipment.
The product is suitable for indoor and outdoor use.
The EVC7.4-1AC-10 must not be used in industrial environments.
The product must be tested in fast charging mode according to IEC 61851 before
its first charging operation using a suitable measuring device for charging
stations.
All components must remain within their permitted operating ranges and their
installation requirements at all times.
The product must only be used in countries for which it is approved or
released by SMA Solar Technology AG and the grid operator.
Use SMA products only in accordance with the information provided in the
enclosed documentation and with the locally applicable laws, regulations,
standards and directives. Any other application may cause personal injury or
property damage.
Alterations to the SMA products, e.g., changes or modifications, are only
permitted with the express written permission of SMA Solar Technology AG.
Unauthorized alterations will void guarantee and warranty claims and in most
cases terminate the operating license. SMA Solar Technology AG shall not be
held liable for any damage caused by such changes.
Any use of the product other than that described in the Intended Use section
does not qualify as appropriate.
The enclosed documentation is an integral part of this product. Keep the
documentation in a convenient, dry place for future reference and observe all
instructions contained therein. This document does not replace any regional,
state, provincial, federal or national laws, regulations or standards that
apply to the installation, electrical safety and use of the product. SMA Solar
Technology AG assumes no responsibility for the compliance or non-compliance
with such laws or codes in connection with the installation of the product.
The type label must remain permanently attached to the product.
IMPORTANT SAFETY INSTRUCTIONS
Keep the manual for future reference.
This section contains safety information that must be observed at all times
when working.
The product has been designed and tested in accordance with international
safety requirements. As with all electrical or electronical devices, there are
residual risks despite careful construction. To prevent personal injury and
property damage and to ensure long-term operation of the product, read this
section carefully and observe all safety information at all times.
DANGER
Danger to life due to electric shock when live components or cables are
touched. High voltages are present in the conductive components or cables of
the product. Touching live parts and cables results in death or lethal
injuries due to electric shock.
- Do not touch non-insulated parts or cables.
- Disconnect the product from voltage sources and ensure it cannot be reconnected before working on the device.
- Wear suitable personal protective equipment for all work on the product.
DANGER
Danger to life due to electric shock in case of overvoltages and if surge
protection is missing. Overvoltages (e. g. in the event of a flash of
lightning) can be further conducted into the building and to other connected
devices in the same network via the network cables or other data cables if
there is no surge protection. Touching live parts and cables results in death
or lethal injuries due to electric shock.
- Ensure that all devices in the same network are integrated in the existing overvoltage protection.
- When laying the network cable outdoors, ensure that there is suitable surge protection at the network cable transition from the product outdoors to the network inside the building.
- The Ethernet interface of the product is classified as “TNV-1” and offers protection against overvoltages of up to 1.5 kV.
WARNING
Danger to life due to fire and explosion
In rare cases, an explosive gas mixture can be generated inside the product
under fault conditions. In this state, switching operations can cause a fire
inside the product or explosion. Death or lethal injuries due to hot or flying
debris can result.
- In the event of a fault, do not perform any direct actions on the product.
- Ensure that unauthorized persons have no access to the product.
- Disconnect the AC circuit breaker, or keep it disconnected in case it has already tripped, and secure it against reconnection.
- Only perform work on the product (e.g., troubleshooting, repair work) when wearing personal protective equipment for handling of hazardous substances (e.g., safety gloves, eye and face protection, respiratory protection).
WARNING
Risk of injury due to toxic substances, gases and dusts.
In rare cases, damages to electronic components can result in the formation of
toxic substances, gases or dusts inside the product. Touching toxic substances
and inhaling toxic gases and dusts can cause skin irritation, burns or
poisoning, trouble breathing and nausea.
- Only perform work on the product (e.g., troubleshooting, repair work) when wearing personal protective equipment for handling of hazardous substances (e.g., safety gloves, eye and face protection, respiratory protection).
- Ensure that unauthorized persons have no access to the product.
CAUTION
Risk of burns due to hot enclosure parts
Some parts of the enclosure can get hot during operation. Touching hot
enclosure parts can result in burn injuries.
- Do not touch the enclosure during operation.
- Wear suitable personal protective equipment.
CAUTION
Risk of injury due to weight of product
Injuries may result if the product is lifted incorrectly or dropped while
being transported or mounted.
- Wear suitable personal protective equipment for all work on the product.
CAUTION
Risk of injury due to weight of enclosure lid of product
Dropping the enclosure lid during assembly or disassembly of the enclosure lid
can cause injuries.
- Wear suitable personal protective equipment for all work on the product.
NOTICE
Damage to the product due to sand, dust and moisture ingress
Sand, dust and moisture penetration can damage the product and impair its
functionality.
- Only open the product if the humidity is within the thresholds and the environment is free of sand and dust.
- Do not open the product during a dust storm or precipitation.
NOTICE
High costs due to inappropriate Internet tariff
Depending on use, the data volume of the product transferred via the Internet
may vary in size. The data volume depends, for example, on the number of
devices in the system, the frequency of device updates, the frequency of data
transfer to Sunny Portal or the use of FTP push. High costs for the Internet
connection can be the result.
- SMA Solar Technology AG recommends using an Internet flat rate.
NOTICE
Damage to the product due to cleaning agents
The use of cleaning agents may cause damage to the product and its components.
- Clean the product and all its components only with a cloth moistened with clear water.
Symbols on the Product
Icon: Explanation
-
Beware of electrical voltage
The product operates at high voltages. -
Beware of hot surface
The product can get hot during operation. -
Observe the documentations
Observe all documentations supplied with the product. -
Charge mode
The symbol together with the green LED indicates that the product is in charging mode. -
Observe the documentations
Together with the red LED, this symbol indicates an error. -
Data transmission
Together with the blue LED, this symbol indicates the status of the network connection. -
Fast charging
This symbol is located on the rotary switch and indicates the switch position for fast charging. -
Smart charging
This symbol is located on the rotary switch and indicates the switch position for charging controlled by the energy management system. -
Alternating current
-
WEEE designation
Do not dispose of the product together with the household waste but in accordance with the disposal regulations for electronic waste applicable at the installation site. -
The product is suitable for outdoor installation.
-
Degree of protection IP65
The product is protected against the penetration of dust and water that is directed as a jet against the enclosure from all directions. -
CE marking
The product complies with the requirements of the applicable EU directives. -
UKCA marking
The product complies with the regulations of the applicable laws of England, Wales and Scotland. -
RoHS labeling
The product complies with the requirements of the applicable EU directives.
EU Declaration of Conformity
within the scope of the EU directives
- Radio Equipment Directive 2014/53/EU (22.5.2014 L 153/62) (RED)
- Restriction of the use of certain hazardous substances 2011/65/EU (L 174/88, June 8, 2011) and 2015/863/EU (L 137/10, March 31, 2015) (RoHS)
SMA Solar Technology AG confirms herewith that the products described in this document are in compliance with the fundamental requirements and other relevant provisions of the above-mentioned directives. The entire EU Declaration of Conformity can be found at www.SMA-Solar.com.
UK Declaration of Conformity
according to the regulations of England, Wales and Scotland
- Electromagnetic Compatibility Regulations 2016 (SI 2016/1091)
- Electrical Equipment (Safety) Regulations 2016 (SI 2016/1101)
- Radio Equipment Regulations 2017 (SI 2017/1206)
- The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012
SMA Solar Technology AG confirms herewith that the products described in this document are in compliance with the fundamental requirements and other relevant provisions of the above-mentioned regulations. The entire UK Declaration of Conformity can be found at www.SMA-Solar.com.
Scope of Delivery
Mounting
Mounting location
Mounting
Mounting the Connection Cap
Connecting
Connecting the Utility Grid
Connecting Signal Source to Digital Input
Connecting the Charging Cable
Connecting the network
Commissioning
Accessing the user interface via WLAN
Accessing the user interface via LAN
Configuration
Disconnect from voltage sources
System data
- Overvoltage category in accordance with IEC 60664-1 III
- Protection class in accordance with IEC 61140 I
- All-pole sensitive residual-current monitoring unit integrated
- Maximum permissible value for relative humidity, condensing 100 %
- Extended humidity range according to IEC 60721-3-4 0 % to 100 %
- Pollution degree inside the enclosure 2
- Pollution degree outside the enclosure 3
Contact
Access data for the registration in Sunny Portal and WLAN password
- Serial number
- Installer password
- User password
- Device key to reset the administrator account. Store the device key safely.
References
- Solar.com | Get Binding Solar Quotes Online
- SMA Solar Technology AG - Inverter & Photovoltaics Solutions | SMA Solar
- Willkommen bei SMA! | SMA Solar
- SMA service & support. Profitable. Reliable. Affordable. | SMA Solar
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>