eta Dasty 3447 90000 2 In 1 Stick Vacuum Cleaner Instruction Manual
- June 4, 2024
- ETA
Table of Contents
- eta Dasty 3447 90000 2 In 1 Stick Vacuum Cleaner
- SAFETY WARNING
- EQUIPMENT AND ACCESSORIES (Fig. 1)
- VACUUM CLEANER PREPARATION
- USE OF VACUUM CLEANER (Fig. 7)
- REMOVING THE DUST CONTAINER AND FILTER
- CLEANING AND MAINTENANCE
- ENVIRONMENTAL PROTECTION
- TECHNICAL DATA
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
eta Dasty 3447 90000 2 In 1 Stick Vacuum Cleaner
INSTRUCTIONS FOR USE
Dear customer, thank you for purchasing our product. Please read the operating
instructions carefully before putting the appliance into operation and keep
these instructions including the warranty, the receipt and, if possible, the
box with the internal packing.
SAFETY WARNING
GENERAL PROVISIONS:
- Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.
- Check whether the data on the type label corresponds with the voltage in your socket. The power cord plug may only be connected to the electrical socket complying with the applicable standards.
- This appliance may only be used by children aged 8 years or older, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Children younger than 8 years must be kept out of reach of the appliance and its power cord.
- If a vacuum cleaner can be equipped with a hand–held accessory with rotating parts a warning has to be given concerning entrapment.
- Never use the appliance if its adaptor or plug is damaged, if it does not work properly, if it fell down and was damaged. In this case take the appliance to a special service to check its safety and proper function.
- Never immerse the charger, the battery and the motor part of the vacuum cleaner into water (even partially) and protect them against humidity!
- Always turn the appliance off before emptying the tank or before maintenance.
- Never leave the product unattended when in operation!
- Do not charge the battery if electrolyte is leaking from it.
- The appliance must be disconnected from the power adapter when removing the battery.
- Do not through the battery into fire. There is a risk of explosion!
- In order to ensure safety and proper function of the appliance, use only original spare parts and accessories approved by the manufacturer.
- Only use this appliance for the purpose it was designed for, as specified in this manual. Never use the appliance for any other purpose.
- The manufacturer is not responsible for damage caused by improper use of the appliance and the accessories and its warranty for the appliance does not apply in situations when the safety warnings above are not complied with. Failure to replace or maintain all filters regularly according to the instructions in Chapter IV., V., VI and also using non–original filters, the properties of which resulted in failure or damage of the vacuum cleaner, is also understood to be improper use of the appliance.
USE OF THE APPLIANCE:
-
The product is intended for home use and similar (in shops, offices and similar workplaces, in hotels, motels and other residential environments, in facilities providing accommodation with breakfast). It is not intended for commercial use!
-
Avoid contact with the rotating brush when handling the vacuum cleaner (e.g. with loose clothes, hair, fingers, jewellery, bracelets etc.).
-
Do not leave the floor nozzle with the rotation brush on in one place for too long! It could cause damage to the surface vacuumed!
-
The floor nozzle with the rotation brush is not intended for vacuuming impurities from carpets with high pile.
-
Never use the vacuum cleaner nor touch the adaptor with wet hands or feet!
-
Never use (switch on) the vacuum cleaner if it is placed in the holder and it is being charged!
-
Always switch off the vacuum cleaner when charging the battery and after the vacuum cleaner was used.
-
Do not vacuum wet or moist floor coverings, do not use the vacuum cleaner for outdoor areas! When moisture gets into the aggregate, there is a risk of its damage and disabling it. This defect is not covered by the warranty.
-
Do not vacuum sharp objects (e.g. glass, shatter), hot, flammable, explosive items
(e.g. ash, hot cigarette butts, gasoline, thinners and aerosol vapours) or greases
(e.g. fats, oils), caustic agents (e.g. acids, solvents). Vacuuming these objects may lead to damage of the dust filters or the vacuum cleaner. -
Pores of the micro filters may be clogged when vacuuming very fine dust. Thus, air permeability will be reduced and the suction performance will drop. In this case, micro–filters have to be cleaned before the container is full. Do not use the vacuum cleaner to vacuum dirt produced during/after construction such as plasterboard dust, fine sand, cement, dust from construction, parts of plaster etc. If this dirt / loose construction materials / loose construction materials into the aggregate, it poses a danger of damage. The warranty repair does not cover this.
ACCESSORIES AND ASSEMBLY OF THE APPLIANCE:
Install the holder, the vacuum cleaner and the appliance within sufficient
distance from flammable objects (e.g. curtains, drapes, wood, etc.), heat
sources (e.g. oven, stove, etc.) and wet surfaces (e.g. sinks, wash–basins
etc.).
ADAPTER:
- If the adaptor of the appliance is corrupted, it has to be replaced by the manufacturer, its service technician or a similarly qualified person so as to prevent dangerous situations.
- WARNING: To charge the battery, use only the network adapter supplied with this appliance.
- To power the appliance, only apply safe small voltage in accordance with the type plate.
- Use the charger in a room only.
- The adaptor supplied with this appliance is intended for this appliance only, do not use it for other purposes. Also, use only the supplied adaptor with this appliance, do not use any other adaptor for charging (e.g. from another appliance).
- The power cord must not be damaged with sharp or hot objects, open fire, it must not be sunk into water or bent over sharp edges.
For trouble-free operation of the vacuum cleaner, please use the tested micro- filters recommended by the producer.
EQUIPMENT AND ACCESSORIES (Fig. 1)
- A – vacuum cleaner
- A1 – ON/OFF button
- A2 – operation signal lights and charging lights
- A3 – handle
- B – dust container
- B1 – container lock button
- B2 – HEPA filter
- B3 – separator
- C – accessories
- C1 – crevice nozzle
- C2 – brush
- D – extension adapter
- D1 – ON/OFF button.
- D2 – suction power control
- D3 – foldable part with handle
- D4 – foldable part lock button
- D5 – vacuum cleaner lid lock button
- E – floor nozzle with rotation brush
- E1 – floor nozzle lock button
- E2 – removable brush
- E3 – brush lock
- E4 – LEDs illuminating the space in front of the vacuum cleaner
- F – mop attachment
- F1 – universal mop pad
- F2 – filling openings
- G – charging stand
- G1 – lower part
- G2 – space for small accessories (crevice nozzle, brush)
- G3 – support
- G4 – charging port
- G5 – support lid lock button
- G6 – hole for fixing on the wall
- H – adapter
- I – screws
- J – wall plugs
VACUUM CLEANER PREPARATION
Remove all packing material, take out the vacuum cleaner and the accessories. Remove all possible adhesion foils, stick-on labels or paper from the appliance.
VACUUM CLEANER ASSEMBLY
When assembling the vacuum cleaner, follow the procedure indicated in Fig. 1.
Select appropriate accessories (Fig. 7) depending on the required use (hand
vacuum cleaner / stick vacuum cleaner). For disassembly, proceed the other way
round and release the locks.
CHARGING THE ACCUMULATOR
Turn the vacuum cleaner off prior to charging! Place the vacuum cleaner in the
extension attachment and then in the charging base G. Connect the adaptor to
the charging connector G4 and plug it to the mains. The accumulator has to be
charged at least for 8 hours prior to the first use. After that, the standard
charging time is approx. 4-6 hours. The status and progress of charging is
indicated by indicator A2.
Operation signal lights and charging lights (A2)
Gradual lighting of blue segments| Accumulator is charging.
Blue light on continuously| Accumulator is charged
– After a while, the indicator light turns off.
Indication of operation
– Individual segments of the indicator light turn off during use, depending on the battery charge status.
Flashing blue| Rotary brush lock
– The rotary brush drive stops, while the E4 LEDs go out. The vacuum cleaner motor will remain running.
– Turn off the vacuum cleaner, eliminate the cause of the brush lock before you can continue vacuuming.
Warning
- The vacuum cleaner can be charged only if it is placed in the charging base G.
- Let the vacuum cleaner recharge as soon as its suction performance is weaker.
- When using the vacuum cleaner for an extended period of time or in a hot environment, the accumulator might be too hot for charging. Let the accumulator cool down prior to charging.
OPERATING TIMES
Set power
| Running Time *
---|---
ETA344790000| ETA344790010*
MIN| Approx. 60 minutes| Approx. 45 minutes
MAX| Approx. 23 minutes| Approx. 15 minutes
Note:** The stated operating times are based on ETA‘s internal testing
and only apply to a new and fully charged battery. Depending on the age and
wear of the battery, the operating time decreases.
INSTALLING THE CHARGING STAND ON THE WALL
To install the charging stand G on the wall, use the holes G6 on its back.
Mount the stand G on the wall using the enclosed or other suitable connecting
material.
USE OF VACUUM CLEANER (Fig. 7)
Let the vacuum cleaner charge sufficiently prior to using.
CONTROL
- ON/OFF button (A1, D1) – vacuum cleaner ON/OFF switch
Suction power control (D2)
- when pressed once – low suction power
- when pressed twice high suction power
Caution
- When the vacuum cleaner is switched on, it is always at high suction power.
- The suction power may only be adjusted if the vacuum cleaner is put in the extension piece D.
- If you want to vacuum at the low suction power level and only use the handheld vacuum cleaner, first put the vacuum cleaner in the extension piece D and switch it on. Then set the low suction power, and remove the running vacuum cleaner from the extension piece D. The vacuum cleaner will then operate at low suction power level until switched off (or until the battery is discharged).
USING THE MOP ATTACHMENT (F)
- Fill the mop attachment F with water through the filling openings F2 (max 150 ml).
- Attach the F1 mop to the lower part of the moping attachment correctly. Soak and wring the mop before use.
- When filled and assembled, fit the mop attachment to the floor nozzle E (Fig. 1, 5).
- Mop the floor with smooth movements.
Notes
- The mop attachment can be used while vacuum cleaning is on or off. If you are mopping and vacuuming at the same time, first move the vacuum cleaner forwards on the surface you are cleaning and then return using the same path you have already vacuumed and cleaned. This will ensure the proper sequence of the cleaning process
- vacuum cleaning to get rid of any dirt first, followed by floor mopping.
- With the mop attachment you can mop an area of up to 40 m2 with one fill.
REMOVING THE DUST CONTAINER AND FILTER
DUST CONTAINER REMOVAL
When taking out the dust container B follow the procedure indicated in Fig. 1.
Dispose of dirt contained in the dust container with regular household waste.
An emptied and cleaned container is to be put back into the vacuum cleaner in
reverse order.
INPUT FILTER REPLACEMENT
To remove the input filter, follow the procedure indicated in Fig. 1. To fit a
new input filter in the vacuum cleaner, proceed in reverse order.
CLEANING AND MAINTENANCE
Notes
- For hygienic purposes we recommend that you empty the container and clean the filter after each use.
- The maximum suction effect can only be achieved with a clean HEPA filter and an empty dust container.
- We recommend cleaning the HEPA filter each time when the dust container is emptied.
- When vacuuming very fine dust, the HEPA filter pores may become clogged, which reduces air permeability and the suction performance. In this case, it is required to clean the HEPA filter even when the tank is not full.
Clean the surface of the vacuum cleaner, extension attachment, charging base and adaptor with a soft wet cloth. Do not use any rough and aggressive detergents!
-
Accessories
After any vacuuming it is recommended to check visually the brushes or collectors for possible impurities. If there are some impurities, remove them. -
Floor nozzle with rotary brush
Remove any dirt (especially hair, animal hairs, etc.) stuck to the brush. To make cleaning easier, the brush can be removed (Fig. 4). -
Mop attachment
Let any excessive water (solution) drain away from the mop attachment,
e.g. to a washbasin. Rinse the attachment F under running water. The mop pad F1 can be washed in a washing machine at 60 °C and dried in a tumble dryer. -
Dust container
Rinse the plastic parts (B, B3) under running water. Allow all the parts to dry out properly before their re-use. -
HEPA filter
Shake out the input HEPA filter B2 gently, or blow it out. If the HEPA filter is very dirty, you can rinse it under running lukewarm water. Allow it to dry out properly.
Caution
- If you clean the HEPA filter with water, its filtration properties will deteriorate. The filter cannot be washed more than three times. After that, a new filter needs to be purchased.
- We recommend that you replace the HEPA filter twice a year.
- The HEPA filter is not suitable for washing in the dishwasher.
- Failure to clean or replace the HEPA filter as required may cause a defect of the vacuum cleaner!
ENVIRONMENTAL PROTECTION
If the dimensions allow, there are labels of materials used for production of packing, components and accessories as well as their recycling on all parts.
The symbols specified on the product or in the accompanying documentation mean that the used electrical or electronic products must not be disposed of together with municipal waste. For proper disposal of the product, hand it over at special collection places where it will be received free of charge. Suitable disposal of the product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations. The appliance is equipped with the Li-Ion battery with long life. For environmental protection it is necessary to remove the battery from the appliance after its service life and the battery and the appliance must be disposed of safely using special collection networks. Ask for more details at the local authority or at the local waste collection site.
Removing the accumulator
You can remove the accumulators from the appliance only after they have been
completely discharged (i.e. let the vacuum cleaner run until its motor stops).
Unscrew the screws and open the vacuum cleaner. Gradually cut off the supply
conductors and remove the accumulators (Fig. 6).
TECHNICAL DATA
- Protection class (vacuum cleaner) : III.
- Accumulator (ETA3447 / ETA3447-10) : 21.6 V / 14.4 V Li-Ion
- Weight (kg) approx. (hand vacuum cleaner / stick vacuum cleaner): 1.1 / 2.5
- Size of the product (mm) (hand vacuum cleaner) : 425 x 110 x 140
- Size of the product (mm) (stick vacuum cleaner) : 260 x 185 x 1160
Charging adapter | ETA344790000 | ETA344790010 |
---|---|---|
Manufacturer’s name or trademark, business registration number and address | ||
ETA | ETA | |
Model identifier | JOD-S-270050GS | JOD-S-180050GS |
Input voltage | 100-240 V (AC) | 100-240 V (AC) |
Input frequency | 50/60 Hz | 50/60 Hz |
Output voltage | 27.0 V (DC) | 18.0 V (DC) |
Output current | 0.5 A | 0.5 A |
Output power | 13.5 W | 9.0 W |
Average efficiency in active mode | 115 V (DC): 88.31 %; |
230 V (DC): 88.10 %
| 115 V (DC): 81.91 %;
230 V (DC): 81.81 %
Low load efficiency (10%)| 115 V (DC): 85.76 %;
230 V (DC): 81.41 %
| –
Power consumption without load| 115 V (DC): 0.041 W;
230 V (DC): 0.068 W
| 115 V (DC): 0.054 W;
230 V (DC): 0.074 W
Appliance protection class| II.| II.
- The manufacturer reserves the right to change the technical specifications and accessories for the respective models.
- Guarantee of 24 months does not apply to decrease in the accumulator’s effective capacity caused by its use or age. Effective capacity gradually decreases depending on the method of use of the accumulator.
- Replacement of parts that require intervention in the electric part of the appliance must be carried out by a specialized service! Failure to comply with the instructions of the manufacturer will lead to expiration of the right to guarantee repair!
- WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING OR IN THE INSTRUCTIONS MANUAL:
- HOUSEHOLD USE ONLY; DO NOT IMMERSE IN WATER OR OTHER LIQUIDS;
- TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.
- – Read operator’s manual
- Removable power supply unit
- The symbol indicates a WARNING.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>