MOOER ME Cab X2 Stereo Cabinet Simulator Pedal Owner’s Manual
- June 10, 2024
- Mooer
Table of Contents
MOOER ME Cab X2 Stereo Cabinet Simulator Pedal
Precautions
PLEASE READ CAREFULLY BEFORE PROCEEDING
Power Supply
Please connect the designated AC adapter to an AC outlet of the correct
voltage. Be sure to only use an AC adapter which supplies 9V DC, 300mA. Unplug
the AC power adapter when not in use or during electrical storms.
Location
To avoid deformation, discoloration, or other serious damage, do not expose
this unit to the following conditions:
- Direct sunlight or other heat sources
- Excessively dusty or dirty locations
- Magnetic fields
- Strong vibrations or shocks
- High humidity or moisture
Radio Frequency Interference
Radios and televisions placed nearby may experience reception interference.
Operate this unit at a suitable distance from radios and televisions.
Cleaning
Clean only with a soft, dry cloth. If necessary, slightly moisten the cloth. Do not use abrasive cleanser, cleaning alcohol, paint thinners, wax,solvents, cleaning fluids, or chemical-impregnated wiping cloths.
Features
- High-quality I loading stereo cabinet simulation pedal
- Includes 14 user preset slots that can store two different cabinet simulation settings each
- 11 factory cabinet simulation files with support for loading third-party impulse response files
- Choose between mono or stereo setups
- Footswitch can be assigned as a tradition on/off switch or to switch between presets
- Dual inputs (stereo) and outputs (stereo) for stereo/mono setup
- Comes with a specialized editor software for preset management and IR loading
Top panel
-
TYPE-C USB port:
-
Connect to computer editor software to manage preset, loading IR and firmware updates.
-
DV 9C
-
Connect to center negative power supply with 9V and at least 300mA current draw.
-
Recommend to use the original power supply to avoid unexpected noise.
-
HIGH CUT
-
High-frequency cut adjustment (Range from 3kHz to 20kHz)
-
LEVEL
-
Volume level adjustment
-
LOW CUT
-
LATENCY
-
CAB
-
Low-frequency cut adjustment (Range from 25Hz to 500Hz)
-
Latency value adjustment from 0 to 20ms.
-
Select cabinet simulation from 11 factory setting files.
-
SAVE
Press to switch between 1-14 preset slots, press and hold to confirm saving preset. -
Left footswitch LED:
Indicate the current cab sim is type A or type B. Blue for A, RED for B. -
Right footswitch LED:
Indicate the on/off status of the pedal. BLUE LED for on, LED off for off. -
Preset LED:
Indicates currently selected preset slot. -
Left (A/B) footswitch:
Press to switch A/B cab sim -
Right (BYPASS) footswitch:
Press to switch on/off the currently selected cab sim -
INPUT-L (MONO):
1/4″ unbalanced (TS) monaural output jack. Please utilize this jack for mono input set up (It is the left input of the stereo setup) -
INPUT R
1/4″unbalanced (TS) monaural output jack (It is the right input of the stereo setup) -
OUTPUT A (Left)
1/4″ unbalanced (TS) monaural output jack, left cab sim analog output jack -
OUTPUT B (Right)
1/4″ unbalanced (TS) monaural output jack, right cab sim analog output jack -
PHONES
1/8″ stereo audio headphone output jack -
Factory cab list
Factory cabinet simulations list
The regular frequency range of high and low cut
Instructions
Select Preset
Press SAVE button to scroll through the 14 preset slots; Or you can press two
footswitches simultaneously to enter preset select mode, the LED of both
footswitches, the LED of SAVE button will blink in RED. In this mode, press
left/right footswitch to scroll up/down the 14 presets.
The preset select mode will exit and be back to normal mode if idle for more
than 3 seconds. In normal mode, the LED of both footswitches and SAVE button
will stay on.
Tone adjustment for left/right output
- Each preset can store the cab sim models, parameters the of left output and right output individually. Press the left footswitch to switch the A (left) output and B (right) output.
- The color of the LED button indicates the currently selected output. Blue means the left output is selected while red means the right output is selected. The controllable parameters include LEVEL, TYPE, LATENCY, LOW CUT, HIGH CUT and CAB.
- In the normal footswitch mode, press right footswitch to turn on/off the cab sim of left/right output.
- The PRESET LED will blink when preset parameter changes and have not been saved.
Save Presets
Press and hold the SAVE button for 2 seconds to save the currently edited
parameters. The button LED will blink to confirm saving is complete.
Factory Reset
Unplug the power cord then press and hold the SAVE button while plugging in
the power cord to power on the unit. The PRESET LED will start to blink.
Release the button and wait for the LED to start blinking to confirm the reset
was successful. This operation can be cancelled by powering off the pedal
before releasing the SAVE button.
Notice : Factory reset will clear all user files, including the third-
party impulse response files.
Recommended setup
Pedalboard Mono Setup
Pedalboard Stereo Setup
Multi-Effect Setup
FX LOOP with Amplifier
Notice : In this setup, we recommend setting the output connecting to the amplifier to bypass the cab sim. The other output connecting to the mixer/FRFR system should have the cab sim on.
CAB X2 editor software
CAB X2 supports computer editor software. Users can quickly adjust parameters,
manage presets, load impulse response files, backup users files, etc..
Download
Visit the official MOOERAUDIO website
(http://www.mooeraudio.com/download.html) and download the software version
that matches the operating system (OS) of your computer. OS requirements: Win
7 or higher, Mac OS 10.11 or higher.
Connection
After finishing the installation, connect your CAB X2 to your computer using
the USB cable that comes with the unit. Open the CAB X2 EDIT software and
select the icon on the top right corner to confirm connection.
In the CABINET TYPE area in the left bottom, there are two different colors.
Blue represents the left output signal while Red represents the right output
signal.
Select Preset
Click on the numbers to switch to the relevant preset patch.
Select Cabinet Simulation
Click on the drop-down menu under the cab picture to view and select cab sim
.
Select desired cabinet simulation on the right side. Right click a desired cab
sim model, decide if it is set to left output or right output in the pop up
window.
Preset Saving
Click on the icon to save the currently selected preset.
Preset Management
Export Preset: Drag the number on the right-top PRESET (Device) area to the
COMPUTER area to export the preset file from the CAB X2 to the computer
.
Import Preset: Drag the preset from the COMPUTER area to the desired number on
the PRESET (Device) area to import the preset file from the computer to the
CAB X2.
Click on the icon in the COMPUTER area to open the target folder of preset
files in your
computer.
Notice :
- Put the preset files into this folder and click the icon. Those preset files will be shown in the COMPUTER area of the software.
- Preset files do not include third-party impulse response files.
Firmware/software update
Click on the icon to update the firmware or editor software. After firmware
update is done, the CAB X2 will reboot automatically.
For editor software update, it will switch to the download center of
MOOERAUDIO official website, you can download the software on the software
download page and install it.
Factory Reset
Click on the icon to enter factory reset menu. A confirmation window will pop
up, click on Yes to confirm reset. The CAB X2 will reboot automatically after
reset is done.
Notice : Factory reset will clear up all the preset patches and third-
party IR files.
Backup/Restore
Select the icon, click on the button to backup all preset files in your CAB
X2. Select the target location to start backing up files. The preset files
will be packaged into a single. bfl file.
Notice : This backup file”. bfl” includes impulse response files.
Effect list
Specification
- Input : 2*1/4″ monoauraljack (Impedance value: 1M ohms)
- Output :
- 2*1/4″ monoauraljack (Impedance value: 510 ohms),
- 1*1/8″ stereo audio output jack (Impedance<1 Ohms)
- Power supply : 9V DV center negative (Please ensure the voltage value of power supply is not more than 9V, ensure the polarity is correct.)
- Current Draw :300mA
- Dimension: 75×115x33mm
- Weight: 0,334 kg
- Accessories: Owner’s manual, USB TYPE-C to TYPE-A cable; DC 9V power supply, Quick guide, Sticker
- Format: WAV
- Sample Rate: 44.1kHz (support loading file with different sample rate)
- Sample Accuracy: 24 bit
- Sample Length: 2048*2
www.mooeraudio.com
SHENZHEN MOOER AUDIO CO. LTD 6F, Unit D, Jinghang Building, Liuxian 3rd Road,
Bao’ an 71 District, Shenzhen, China. 518133 Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>