KUFATEC 36492-1 Front and Rear View Camera Installation Guide
- June 15, 2024
- KUFATEC
Table of Contents
- KUFATEC 36492-1 Front and Rear View Camera
- Product Information: Front and Rear View Camera
- Product Usage Instructions
- Copyright
- Requirements for the Intended Use
- How to Connect a Cable to Another
- Assembly Instructions
- Assembling the Vehicle
- Visual Diagram Description
- Frequently Asked Questions (FAQ)
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
KUFATEC 36492-1 Front and Rear View Camera
Product Information: Front and Rear View Camera
Specifications:
- Version: v1.0 (12.05.2022)
- Manufacturer: Kufatec GmbH & Co. KG
- Address: Dahlienstr. 15, 23795 Bad Segeberg
- Email: info@kufatec.de
v1.0 (12.05.2022)
Kufatec GmbH & Co. KG – Dahlienstr. 15 – 23795 Bad Segeberg – e-mail: info@kufatec.de
Document Title | Installation Instructions Front and Rear View Camera |
---|---|
Version | 1.0 |
Date | 12.05.2022 |
Company | Kufatec GmbH & Co. KG |
Address | Dahlienstr. 15 – 23795 Bad Segeberg |
info@kufatec.de |
Product Usage Instructions
Liability Exclusion
Please note that the manufacturer does not take responsibility for any
damages or injuries resulting from improper installation or usage of the front
and rear view camera. Follow the instructions carefully to ensure safe and
correct installation.
Copyright
All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the manufacturer.
General Notes
Before starting the installation process, read through the entire manual to
familiarize yourself with the steps and requirements. Make sure you have all
the necessary tools and equipment.
Safety Instructions
Ensure that the vehicle is parked in a safe and secure location before
starting the installation. Disconnect the battery to avoid any electrical
hazards during the installation process. Use caution when working with airbags
and follow the safety instructions provided in section 10.
Requirements for the Intended Use
To use the front and rear view camera, your vehicle must meet the following requirements:
- Compatible vehicle model
- Working electrical system
- Appropriate clearance for camera installation
How to Connect a Cable to Another
To connect cables together, follow these steps:
- Identify the cables to be connected.
- Strip the insulation from the cable ends.
- Twist the exposed wire ends together.
- Secure the connection with electrical tape or wire connectors.
Note Cable Inscription/Color
Refer to the following table for cable inscriptions and colors:
Cable Inscription | Color |
---|---|
Example1 | Red |
Example2 | Black |
Assembly Instructions
The assembly instructions involve disassembling various parts of the vehicle and connecting the front and rear view camera components. Follow the steps provided in the relevant sections of this manual for detailed instructions.
The following illustration shows the cable routing as well as the position of the individual components.
- Positioning and routing of cables at various points of the vehicle as indicated in the diagrams.
Note: Please be aware that this overview is only for illustration purposes. Always lay the cable set in the most convenient and shortest way possible. For a detailed description of the cable routing, please refer to the relevant sections of the following manual.
Disassembly Coverings Front Driver’s Side
Follow the steps below to disassemble the coverings on the front driver’s
side:
- Step 1: Remove screw A using a screwdriver.
- Step 2: Remove clip B by gently prying it off.
- Step 3: Lift the covering C to access the components underneath.
Disassembly Glove Compartment
Follow the steps below to disassemble the glove compartment:
- Step 1: Open the glove compartment and remove all contents.
- Step 2: Locate the screws D on the sides of the glove compartment.
- Step 3: Remove the screws D using a screwdriver.
- Step 4: Gently pull the glove compartment towards you to detach it from its hinges.
Assembling the Vehicle
Once all the necessary components have been installed and connected, follow these steps to assemble the vehicle:
- Step 1: Reattach all disassembled coverings, compartments, and parts in reverse order.
- Step 2: Ensure that all connections are secure and cables are properly routed.
- Step 3: Test the front and rear view camera functionality before closing up the vehicle.
Visual Diagram Description
The visual diagram includes a side and top view of a vehicle with numbered points indicating cable routing and component positions. Red lines represent the path that cables should follow within the vehicle, connecting points 1 through 6. Specific details for each numbered position are likely detailed in the manual’s relevant sections.
Installation Instructions Front and Rear View Camera
v1.0 (12.05.2022)
Kufatec GmbH & Co. KG – Dahlienstr. 15 – 23795 Bad Segeberg – e-mail: info@kufatec.de
Figure 3: Fahrzeug “Ubersicht
· 1 Front camera · 2 Fuse box · 3 Gateway · 4 Control unit · 5 Ground pin · 6
Rear view Camera
Please be aware that this overview is only for illustration purposes. Always
lay the cable set in the most convenient and shortest way possible. For a
detailed description of the cable routing, please refer to the relevant
sections of the following manual.
Kufatec GmbH & Co. KG – Dahlienstr. 15 – 23795 Bad Segeberg – e-mail: info@kufatec.de
Frequently Asked Questions (FAQ)
Can I install the front and rear view camera myself?
Yes, you can install the front and rear view camera yourself by following the instructions provided in this manual. However, if you are not familiar with vehicle electronics or feel uncomfortable with the installation process, it is recommended to seek professional assistance.
Can I use the front and rear view camera with any vehicle model?
The front and rear view camera compatibility may vary depending on the vehicle model. Please refer to the product specifications or contact our customer support for more information regarding compatibility.
What is the purpose of the document?
This document provides installation instructions for front and rear view cameras in vehicles.
What is the version and date of the document?
The document is version 1.0, dated 12.05.2022.
How should the cable set be laid out?
The cable set should be laid out in the most convenient and shortest way possible, with reference to the detailed description in the manual.
Where can I find more detailed instructions on cable routing?
Detailed instructions on cable routing can be found in the relevant sections of the manual provided.
Q2: What should I do if I encounter difficulties during the
installation?
A2: If you face any difficulties during the installation process or have
any questions, please contact our customer support at
info@kufatec.de. Our team will be happy to assist
you.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>