StarTech com USB210AIND-USB-A-HUB 10-Port Industrial USB User Guide
- June 10, 2024
- StarTech com
Table of Contents
StarTech com USB210AIND-USB-A-HUB 10-Port Industrial USB
Product Diagram (USB210AIND-USB-A-HUB)
Front View
Rear View
Ports/Parts | Function |
---|---|
1 | DC Power Input |
- Connect a +5~24 V DC Power Source
2| DC 2-Wire Terminal Block Power Input|
- Connect a +5~24 V DC Power Source
3| USB Type-B Host Port|
- USB Type-B 480 Mbps (USB 2.0)
- Connect the USB Hub to a Host Computer
4| USB Type-B Host Port|
- USB Type-A 480 Mbps (USB 2.0)
- Connect up to 10 USB Type A Peripheral Devices
5| Mounting Holes|
- Wall mount the USB Hub
- Mount the USB Hub to the side/underside of a Desk
6| DIN Rail Mounting Holes, Horizontal|
- Used to Horizontally mount the USB Hub to a DIN Rail
7| DIN Rail Mounting Holes, Vertical|
- Used to Vertically mount the USB Hub to a DIN Rail
Package Contents
- USB 2.0 Hub x 1
- DIN Rail Mounting Brackets x 2
- USB 2.0 Type-A to Type-B Cable x 1
- Screw Kit x 1
- Quick-Start Guide x 1
Requirements
For the latest product information, technical specifications, manuals, and declarations of conformance, please visit: www.startech.com/USB210AIND- USB-A-HUB
- Flat Head Screwdriver
- Phillips Head Screwdriver
- Writing Utensil
- Level
- DC Power Source
- (Optional) Stud Finder & Electric Driver
Installation
Notes:
- Connect the Power Source after all the other installation steps have been completed.
- There are two ways to power the USB Hub.
Using an external DC Power Adapter or a Terminal Block Power Source. Voltage (+5 – 24 V DC).
Connect the USB Ports
- Connect the USB 2.0 Type-A to Type-B Cable to the USB Type-B Host Port, located on the USB Hub, and to a USB-A Port, located on the Host Computer.
- The Host Computer’s Operating System will detect the USB Hub.
- Connect up to 10 USB Peripheral Devices to the USB Type A Ports, located on the USB Hub.
Power the Hub
Power the Hub Using the 2-Wire Terminal Block
-
Remove the Terminal Block Connector Housing from the USB Hub’s Casing.
-
Loosen the screws for the Terminals located on the Terminal Block Connector, using a Flat Head Screwdriver.
-
Connect the Positive and Negative Wires from the DC Power Source (+5 – 24 V DC) to the Terminals on the Terminal Block Connector, the Terminals are marked on the USB Hub’s Casing.
Note: Ensure the polarity of the power input is correctly matched with the DC 2-Wire Terminal Block Pins to function properly and to prevent damage to the USB Hub and any connected peripherals. -
Insert the Terminal Block Connector Housing back into USB Hub.
Power the Hub Using an External Power Adapter
- Connect the Power Adapter to the Power Input Port, located on the front of the USB Hub and to an AC Electrical Outlet.
Surface Mounting
Note: Always mount onto Wall Studs, when installing the USB Hub onto drywall.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. Changes or modifications not expressly approved by
StarTech.com could void the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du
Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept
any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de
l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and
Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of thirdparty companies not related in any way
to StarTech.com. Where they occur these references are for illustrative
purposes only and do not represent an endorsement of a product or service by
StarTech.com, or an endorsement of the product(s) to which this manual applies
by the third-party company in question. StarTech.com hereby acknowledges that
all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the
property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United
States or other countries.
- Optional) If mounting onto drywall, use a Stud Finder to locate the Wall Stud(s) on your wall.
- Hold the Hub in the desired mounting location, and mark the location of the Mounting Holes, using a Writing Utensil (use a level to ensure the two Mounting Holes are level).
- Using an Electric Driver, drill Pilot Holes into each of Mounting Hole Marks.
- Hold the Hub in the desired mounting location, aligning the Mounting Holes on the Hub with the Pilot Holes created in Step 3.
- Insert the Mounting Screws (x 2) through the Wall Mounting Holes and into the Wall, and tighten the Mounting Screws until the Hub is securely fastened to the Wall, using a Phillips Head Screwdriver.
DIN Rail Mounting
Horizontal
- Align the Din Rail Brackets (x 2) with the DIN Rail Mounting Holes, Horizontal (x 4), located on either side of the USB Hub (rear).
- Insert the Mounting Screws (x 4) through the DIN Rail Brackets and into the USB Hub.
- Using a Phillips Head Screwdriver, tighten the Mounting Screws. Be careful not to over-tighten the Mounting Screws.
Vertical
- Align the Din Rail Bracket (x 1) with the DIN Rail Mounting Holes, Vertical (x 2) located on the USB Hub (rear).
- Insert the Mounting Screws (x 2) through the DIN Rail Bracket and into the USB Hub.
- Using a Phillips Head Screwdriver, tighten the Mounting Screws. Be careful not to over-tighten.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer
to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
Safety Measures
- If product has an exposed circuit board, do not touch the product under power.
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com Ltd
Siriusdreef 17-27
2132 WT Hoofddop
The Netherlands
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
References
- Industrial 4 Port USB C Hub 10Gbps 3A/1C - Industrial USB Hubs | StarTech.com
- 10-Port Industrial USB 2.0 HUB, Metal - Industrial USB Hubs | StarTech.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>