PHILIPS EasySense SNS412 MC Fixture Mount Wireless Node Sensors Installation Guide

PHILIPS EasySense SNS412 MC Fixture Mount Wireless Node Sensors

Wireless Node Part Number

Blue LEDWiring Diagram*

• Wiring diagram for 40W driver shown. Other drivers have different wiring diagrams. Consult datasheet for driver for applicable wiring diagram.

Sensor Dimensions (in/mm)

Mounting Dimensions (in/mm)

Mounting in U-shaped slot in sheet metal (max thickness 1 mm)

Mounting in cut-out in sheet metal (thickness 0.7 mm to 1.0 mm)

Note: Consult factory for accessory mounting ring to secure sensor to cut-out.

Fixture with EasySense installed

Mounting in a slot

Mounting in a cut-out with mounting bracket

Accessory Mounting Ring

• Part Number SMR-50 / Set of 50.
• Ordered separately, not included

Accessory Mounting Bracket

• Part Number SMB-50 / Set of 50.
• Ordered separately, not included.

Note: Below data applicable for SNS412 MC..

Electrical Information

Input Voltage| Powered by SR driver low-voltage interface
Current Consumption| 13mA
Nominal Power Consumption| 200mW
Standby Power| < 1 W on luminaire level, including driver standby power
Environment & Approbation
Operating Ambient Temperature Range| -30°C to 65°C
Operating Humidity| 20% – 85% non condensing
Storage Temperature| -30 °C – 85 °C
Storage Humidity| 0-95% non condensing
Max Case Temperature (Tcase)| 65°C
Agency Approbations| UL, FCC; Tested and approved for use in plenums
Limited Warranty| 5 years
Digital Interface| Xitanium SR
Other
Status Indicators| Yellow LED always on
No. Drivers per Node| Four (max)
Field Configuration| via BLE, parameters set via Philips MasterConnect App

Operation and Configuration via Mobile App

SNS412 MC requires commissioning to operate. The node can be commissioned and configured via the Philips MasterConnect app through Bluetooth LE. For a complete description of the features and default settings—as well as details on the app—refer to www.philips.com/easysense.

FCC and IC Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules for the United States and Industry Canada (IC) license-exempt RSS standard(s). These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment and is intended for commercial use only. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Any changes or modifications not expressly approved by Signify could void the user’s authority to operate this equipment.

This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

© 2023 Signify Holding. All rights reserved. The information provided herein is subject to change, without notice. Signify does not give any representation or warranty as to the accuracy or completeness of the information included herein and shall not be liable for any action in reliance thereon. The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract, unless otherwise agreed by Signify. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips

N.V. All other trademarks are owned by Signify Holding or their respective owners.
philips.com/easysense

Signify North America Corporation
400 Crossing Blvd, Suite 600
Bridgewater, NJ 08807
Tel. 855-486-2216
Signify Canada Ltd.
281 Hillmount Rd,
Markham, ON, Canada L6C 2S3
Tel. 800-668-9008

References

• EasySense Fixture-Mount Sensor - Philips lighting
• EasySense Fixture-Mount Sensor - Philips lighting
• Xitanium Sensor Ready Drivers | Advance | Signify Lighting

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>