CASAINC CA-LS3036BLW LED Anti Fog Wall Mounted Bathroom Vanity Mirror Instruction Manual
- June 10, 2024
- CASAINC
Table of Contents
CASAINC CA-LS3036BLW LED Anti Fog Wall Mounted Bathroom Vanity Mirror
The clock version
The standard version
WARNING AND SAFETY INSTRUCTIONS
Please make sure that you carefully read through this instruction sheet refer back to them during installation to ensure your product is fitted safely and correctly before installing your LED Lighted Mirror fixture. Keep these instructions for future use
WARNING Risk of Fire and Electric Shock
- All fittings must be installed in accordance with current IEE wiring regulations. If in doubt, consult aqualified electrician.
- Switch off the electrical supply at the main circuit board BEFORE installation and maintenance.
- Suitable for indoor use only. This product should be positioned well away from curtains and fabrics. Never cover the mirror.
- Regularly check the cord, the transformer and all other parts for damage. If any part is damaged the product should not be used.
INSTALLATION SAFETY
- Inspect the product immediately upon receipt for the transit damage or missing parts. Handle the product with care and protect against knocks to all sides and edges of the glass.
- Ensure there are no hidden pipes or cables in the wall before drilling.
- Wear suitable eye protection when drilling. Take care if drilling on tiled surfaces in case the drill slips
CAUTION
The light source of this product is non‐changeable light diodes (LED). Do not
disassemble the product, as the light diodes can cause damage to the eyes.
NOTE : The important safeguards and instructions that appear in this
manual are not meant to cover all possible conditions and situations that may
occur. It must be understood that common sense, caution and care, are factors
that can’t be built into any product. These factors must be supplied by the
person(s) caring for and operating the fixture. Do not install this fixture in
hazardous locations.
CHECK PRODUCT LIST AFTER OPENING THE PACKAGE
TOOLS YOU MAY NEED
INSTALLATION MANUAL
-
Level and mark the location (vertically hanging and horizontally hanging)
Notes: -
Fix the mounting bar into the wall firstly with the distance as above drawing;
-
For the mirror with ON/OFF button in the right bottom side, we have the special design to hang the mirror either vertically or horizontally;
-
The distance between each 2 hanging holes is 7⅞ inch.
-
Place the mounting bar against the wall and make some marks on the wall
-
Drill the holes and place the suitable plastic anchors
-
Screw the mounting bar onto the wall with the screw
-
Connect the mirror with the main supply.
-
We provide plug with mirrors.
-
Optional to cut the plug directly, then connect to electrical wiring if using wall switch.
ATTENTION : PLEASE CUT OFF THE MAIN POWER SUPPLY BEFORE WIRING !
-
Hang the mirror onto the mounting bar (vertically hanging and horizontally hanging)
OPERATION INSTRUCTION
ON/OFF and CCT adjustment
- Button turns blue when connected to main supply.
- Button always on as long as connecting to main supply.
- Short‐touch the button to turn on/off the mirror.
- Adjusting color temperatures (CCT) between warm white and cool white by long‐touching the button for seconds.
- Finish setting by withdrawing your finger when the color reaches the one you need.
- Optional to be wired to wall switch by ON/OFF memory function.
ON/OFF and Dimmer
- Short‐touch the button to turn on/off the mirror.
- Long touching the button to adjust the brightness (Dimming).
Press and hold on for 3‐5 seconds
Anti‐Fog Function
- Mirror begins to be warm and defog after pressing the defogger button. Press again to quit the anti‐fog function.
- Note : The defogger will stop automatically after 60 minutes of continuous operation to prevent any damage caused by prolonged high temperature
Clock/Temperature
(This operation is specific to the clock version)
- Turn off the light to set the clock.
- Long touch button 1 or 2 for seconds, the Hour will flash, then short‐touch button 1 and 2 to set Hour.
- Wait for seconds after setting up the Hour, then it will automatically switch to the Minute flash.
- Short‐touch button 1and 2 to set up the Minute.
- Wait seconds after you finish the time setting, the time will be saved automatically.
- The clock shows for 5s, and shift to the temperature showing for 2s, then go back to show the clock.
- It automatically displays the indoor temperature by auto-sensing through the temperature sensor.
- DO NOT cover the temperature sensor.
- Night light will be auto‐on/off according to the brightness surrounding when the rocker switch is keeping turned on.
- If need turn off the nightlight at night, please turn off the rocker switch manually
AFTERCARE INSTRUCTIONS
Clean using a soft dry cloth only when turned off. Never use cleaning agents
or abrasive materials. Do not allow moisture to come into contact with lamp.
THANK YOU FOR YOUR SUPPORT
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>