The Home Depot B0BJKLGCJR 703 Multi Purpose Hose Reel Owner’s Manual

The Home Depot B0BJKLGCJR 703 Multi Purpose Hose Reel Owner’s Manual

TOOLS REQUIRED

Pliers. Adjustable Wrench, Drill (Not included) & Allen Wrench (Included)
Estimated assembly time: 5 minutes (Not including mounting)

 PARTS LIST

A. Crank Handle (1)
B. Allen Screw (1)
C. Leader Hose (1)
D. Hose Reel (1) (Not pictured)

ASSEMBLY INSTRUCTIONS

1. Align the holes in the crank handle (A) with crank handle shaft. Tighten using the Allen wrench and screw (B). Do not over tighten crank handle Allen screw. **Figure 1

**

2. Attach the leader hose (C) to the swivel connector. Figure 2
   
   Note: if you have trouble with the swivel turning and kinking the leader hose. try spraying a silicone spray inside to lubricate the arings. The 0-rings located inside the swive may be dry. You can reach the 0-ring by taking off the retaining clip or spraying inside the opening of the swivel.

3. Attach your garden hose to the hose connection on the hose reel (D) spool. **Figure 3

**

  *  **DO NOT** leave water running through the hose reel unsupervised.
  *  **DO NOT** expose the reel to freezing temperatures with water remaining in the unit.
  * Turn the water off after each use.

INSTALLATION

The rose reel MUST be monied to a sem masonry wall or to wall studs.

BRICK OR MASONRY ANCHOR SLEEVES

The following hardware (not included) IS recommended for Installation:
4)7 or 8 mm x 60 mm masorvy wall anchors (5116′ x 2 102′)
(4)Anchce sleeves
(4) Washers
(4) Loaf washers
(4) Nuts

• Positron and hold your hose red against the WM/masonry wal at a convenient height Mark me postbon of each suspension hole on the wag Remove the hose reel.
• Using a hammer dal drill holes 5/16′ in diameter and at the marked mastic:us on the will
• Insert the masonry wall anchors into the anther sleeve Noxt Mien the anchor and sleeve into the dolled Tides unbl the steel sleeve is completely in the wall
• Place the hose reel on the masonry wall anchors
• Install a washer. lock washer. and nut over each wal anchor and tighten securely.

TIP: Remember to use the correct size and quantity of hardware to properly support the total weight of the unit. A standard 100′ length of garden hose weighs approximately 15 lbs. Filled with water, the additional weight can exceed 20 lbs. The mounting hardware must be able to support the combined weight of the unit. garden hose. plus water.

BRICK OR MASONRY SCREWS

The following hardware (not included) Is recommended for Installation:
(4) 7 or 8 mm x 60 nil) masonry saews (5016″ x 2 la)
(4) Washers

• Postbon and hold your hose reel agensi the ono/masonry watt at a convenient height. Mark the position of each suspension hole on the wall. Remove the hiaSe red.
• Using a hammer dal. Mill peel holes 1/4″ ‘,diameter at the marked positions on the wall.
• Afton the hose reel suspension holes with the plot holes.
• Attach the hose reel to the wall using the concrete screws rich washers arid lighten securely.

NOTE: Drill hole diameters may vary based on anchor sleeve. concrete Screw. and wood screw manufacturer.
Check product recommendations before drilling holes.

WOOD SCREWS

The following hardware (not included) is recommended for installation:
(4)7 or B mob x 80 mm weed screw, (5/16″ x 2 Ur)
(4) Washers

• Using a stud Rider locale the wood studs on your wall.
• Poston and hold your hose reel against the wood was at a convenient height Mark the position of each suspension hole on the watt Remove me hose reel
• Using ai electric dal. drill pilot holes 114′ in diameter at the marked positions on the wad
• Align the hose reel Suspension hoes with the pilot holes.
• Attach the hose reel to the wail using the wood saws won washers and tighten securely

GROUND MOUNTING

This hose reel can also be mounted on a lawn, patio or driveway.

Insert the four bumpers (B) provided into the mounting holes at the hose reel base (E). Figure 1

Note: Lubricating the bumpers with water or a light lubricant will ease the insertion.

CARE INSTRUCTIONS

Your hose reel is manufactured with the finest quality components available. This product will give you many seasons of reliable and functional hose storage. All components are manufactured to rigorous quality standards not common in other consumer grade hose reels available today. As with any steel product, there is always the chance for rust developing over time. Your hose reel finish is designed for industrial applications, but even the toughest of coatings can be compromised by scratches. Such minor surface damage can occur in shipping despite our best efforts. We have found that most scratches occur during assembly and/or installation (in the case of wall mounted hose reels). If the base metal is exposed to the elements long enough, rust will develop. In the case of wall mounted reels, be sure to use stainless steel mounting hardware. We recommend that you periodically inspect your reel for any surface damage. Scratches can easily be repaired by using standard automotive touch-up body paint. Some of our most loyal customers recommend that at the end of each season, the unit be cleaned and painted with a clear acrylic paint.
When you install your hose reel, be sure the hose washers are in place and all fittings are secure. If you live in more temperate climates, be sure to drain the unit of any residual water before storing.

• DO NOT EXPOSE UNIT TO FREEZING TEMPERATURES while water remains in the plumbing system, this can damage the swivel.
• DO NOT leave water running through the reel while not in use or unsupervised.
• DO NOT consume water from garden hose: not fit for human consumption.

WARNING! This product contains one or more chemicals known in the state of California to cause cancer and birth defects or reproductive harm. Wash hands after handling.

TROUBLE SHOOTING GUIDE

Problem: Swivel head is not rotating, causing the leader hose to kink up.
Solution: Remove leader hose and turn the square head of the swivel several times; apply lubricant.

Problem: Your new Liberty hose reel is leaking at the swivel.
Solution: Apply Teflon/Plumber’s Tape on the threads or/and make sure fixtures are tightened. It is normal for the swivel to leak slightly until the 0-rings are wet and have seated. If the leaking continues, try these steps: (It is not necessary to return the hose reel)

1. If the leader hose is attached to the swivel, unscrew the hose and look inside the swivel.
2. Check that the hose washer is inside the nut. You may contact Liberty Garden Products for a new hose washer or obtain one at any hardware store.
3. If your swivel is old, the 0-rings may be worn, please contact us for a new set of 0-rings.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>