Metra 99-7614 Nissan NV Dash Kit Installation Guide

: June 10, 2024
: Metra

Table of Contents

99-7614 Nissan NV Dash Kit
Dash Disassembly
Kit Assembly
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

99-7614 Nissan NV Dash Kit
Installation Guide
Nissan NV 2012-2014, NV (without NAV) 2015-up,
Nissan Quest (without NAV or rear seat entertainment) 2011-2012

99-7614 Nissan NV Dash Kit

KIT FEATURES

ISO DIN radio provision with pocket
ISO DDIN radio provision

KIT COMPONENTS

A) Radio housing
B) Radio brackets (C)
C) ISO DDIN trim plate
D) (4) #8 x 3/8” Phillips screws

WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-7552
Antenna Adapter: • 40-NI12
TOOLS REQUIRED

Panel removal tool
Phillips screwdriver

CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

Dash Disassembly

NV 2012-2014,
NV (without NAV) 2015-up

Unclip and remove the A/C vent to the right side of the factory radio. (Figure A)
Remove the (2) Phillips screws exposed behind vent on radio trim panel. (Figure B)
Unclip and remove the left A/C vent next to the instrument display. (Figure C)
Unclip the top edge of the knee bolster panel below the steering column and let hang. (Figure D)
Unclip the circle trim around the key cylinder.
Unclip and remove the gauge cluster trim panel. (Figure E)
Remove (2) Phillips screws exposed behind the panel on the left side of the radio trim panel. (Figure F)
Unclip and remove the trim panel surrounding the factory radio. (Figure G)
Remove (4) Phillips screws securing the radio. (Figure H)

Quest (without NAV or rear seat entertainment) 2011-2012

Unclip and remove the panels from the bottom left and right side of the center console. (Figure A)
Remove (2) clips per side exposed behind lower panels. (Figure B)
Unclip and pull center console toward rear of vehicle.
Note: You do not have to fully remove console. (Figure C)
Unclip and remove the trim panel to the left of the shifter housing the start/stop button. (Figure D)
Unclip and remove the panel on the end of the passenger side of the dash. (Figure E)
Remove (1) Phillips screw from the trim panel above the glove box then unclip and remove the panel. (Figure F)
Remove (1) Phillips screw from the cup holder panel then unclip and remove the panel. (Figure G)
Remove (2) Phillips screws from the a/c control panel and unclip and let hang. (Figure G)
Remove (2) Phillips screws from the bottom of the radio trim panel including the vents then unclip and remove the panel. (Figure G)
Remove (4) Phillips screws securing the radio. (Figure H)

Kit Assembly

ISO DIN radio provision with pocket

Remove the metal “DIN” sleeve and trim ring from the aftermarket radio.
Secure the radio brackets to the radio housing using the (4) 3/8” Phillips screws provided. (Figure A)
Slide the radio into the bracket/housing assembly and secure using the screws supplied with the radio. (Figure B)
Locate the factory wiring harness and antenna connector in the dash. Metra recommends using the proper mating adapters from Metra and/or AXXESS.
Reassemble the dash in reverse order of disassembly.

ISO DDIN radio provision

Remove the brackets from the factory radio.
Secure the brackets to the aftermarket radio using the screws supplied with the aftermarket radio. (Figure A) Note: 99-7614 radio brackets can be used in place of the factory brackets.
Locate the factory wiring harness and antenna connector in the dash. Metra recommends using the proper mating adapters from Metra and/or AXXESS.
Place the ISO DDIN trim plate on the front of the radio. (Figure B)
Reassemble the dash in reverse order of disassembly.

http://www.metraonline.com

IMPORTANT
If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.
Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians