Aurora AU-A1GSZ9CXB Aone 9W Smart Dimmable GLS Lamp User Manual

: June 4, 2024
: Aurora

Table of Contents

AU-A1GSZ9CXB Aone 9W Smart Dimmable GLS Lamp
Setting up your Smart Lamp
Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

User Manual

AU-A1GSZ9CXB Aone 9W Smart Dimmable GLS Lamp

MODEL| AU-Al GSZ9B/27, AU-A1GSZ9E/27, AU-Al GSZ9CXB, AU-Al GSZ9CXE, AU-Al GSZ9RGBWB, AU-A1GSZ9RGBWE, AU-Al CE14ZCX6
---|---
VOLTAGE (V)| 220-240V
SUPPLY FREQUENCY| 50/60Hz
POWER CONSUMPTION| 9W (AU-Al GSZ9B/27 & AU-A1 GSZ9E/27) 9W (AU-Al GSZ9CXB & AU-A1GSZ9CXE)
9.5W (AU-Al GSZ9RGBWB & AU-Al GSZ9RGBWE) 5.8W (AU-Al CE14ZCX6)
POWER FACTOR| 0.7
LUMENS| 806Im (AU-A1 GSZ9B/27 & AU-A1 GSZ9E/27)
680Im (AU-A1 GSZ9CXB & AU-Al GSZ9CXE)
806Im CO 2700K (AU-A1 GSZ9RGBWB & AU-A1 GSZ9RGBWE) 400Im (AU-A1 CE14ZCX6)
CCT| 2700K (AU-A1GSZ9B/27 & AU-A1GSZ9E/27)
2200K-5000K (AU-Al GSZ9CXB, AU-A1GSZ9CXE, AU-A10E14ZCX6) 2700K-6500K (AU-Al GSZ9RGBWB & AU-Al GSZ9RGBWE)
LAMP BASE| B22 (AU-Al GSZ9B/27, AU-Al GSZ9CXB & AU-Al GSZ9RGBWB) E27 (AU-Al GSZ9E/27, AU-A1 GSZ9CXE & AU-A1 GSZ9RGBWE) E14 (AU-Al CE14ZCX6)
DIMENSIONS (0 x H)| 60mm x 120mm (GLS) 38mm x 110mm (Candle)
START TIME| 0.5s
STAND BY POWER| 0.5W
MAX. OUTPUT RF POWER| 10.5 dBm/mW (GLS) 10 dBm/mW (Candle)
MAX. NUMBER OF DEVICES| Depends on Hub
STANDARD OPERATING TEMPERATURE| -20°C to 25°C
IP RATING| IP20 (Use in dry locations only)
PROTOCOL| Zigbee 3.0
FREQUENCY BAND| 2.40 GHz – 2.483 GHz

Setting up your Smart Lamp

Ensure you have downloaded the Aone App and you have the Aone Hub (AU-HZB5A) installed before trying to add devices.
We recommend only pairing one lighting circuit at a time otherwise there is a risk other devices will be found in other areas.
Ensure the wall switch for the lighting circuit is switched off before fitting the lamp. Your Aurora Smart lamp is fitted in the same way that traditional household lamps are fitted. Once fitted, ensure the lamp is switched off until you are ready to pair your devices.
Open your App and go to the ‘add devices’ icon.
Turn the lamp on, it should automatically flash twice showing it is in pairing mode. The lamps should automatically show on the App pairing screen. Ensure all lamps on the circuit have been discovered.
If any devices have not been found. Press ‘Done’ and delete all the devices and reset the lamps by switching off/on six times. After the sixth time, they should flash twice. Follow Step 4 to pair your lamps again.
Once complete, follow the advice on the App to control your lights, and create spaces, schedules, and scenes.

Warranty

See www.auroralighting.com/warranty for full details of warranties and Extended Warranty Terms and Conditions. The warranty is invalid in the case of improper use, tampering, and removal of the Q.C. date label, installation in an improper working environment, or installation not according to the current edition of the National Wiring Regulations. Should this product fail during the warranty period it will be replaced free of charge, this is subject to correct installation and return of the faulty product.
Aurora does not accept responsibility for any installation costs associated with the replacement of this product. This warranty is in addition to the statutory rights in your country of purchase. Aurora reserves the right to alter specifications without prior notice.

Remember
To turn your Aurora Smart Lamp on or off remotely it must be switched on at the wall/fixture. Your Aurora Smart Lamp should not be dimmed using a wall- mounted dimmer switch as it may cause buzzing or flickering. Keep away from liquids and humidity, Use in dry locations only. Not suitable for emergency lighting.
For lamps with a weight significantly higher than that of the lamps for which they are a replacement, attention should be drawn to the fact that the increased weight may reduce the mechanical stability of certain luminaires and lamp holders and may impair contact making and lamp retention.
The lamp is based on protocol Zigbee 3.0, to control on/off, CCT, and brightness dimming it must be controlled through the App. This product is not suitable for a dimming circuit.
Maintenance
Before replacing the lamp, turn off the mains power and let the lamps cool to avoid electrical shock or burns.
Disconnect your Aurora Smart Lamp before cleaning and keep it away from water and other liquids at all times.
The Aurora Smart Lamp does not contain any serviceable parts so do not attempt to open it.
RED Compliance
There are no restrictions on use.
Hereby, Aurora Limited declares that the radio equipment type listed within this guide are in compliance with Directive 2014/53/ EU. The full text of the EU declaration of conformity is available at the following internet address: auroralighting.com

Environmental Protection (W.E.E.E.)
Aurora’s WEEE Reg.No. WEE/BG0130YX (UK Only)
Waste Electrical & Electronic Equipment Regulations (WEEE) require that any of our products showing this marking (left) must not be disposed of with other household or commercial waste. Aurora does not levy any WEEE disposal charges to its customers for affected WEEE-related products. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate any such product from other waste types and recycle it responsibly at your local facilities. Check with your Local Authority, Recycling Centre, or retailer for recycling advice.
If, when you purchased any Aurora product, your supplier included a WEEE disposal fee, you should then contact your supplier for advice on his take- back of the product for the correct disposal.

www.auroralighting.com
Document Version: AU-A1_GLS_Candle_V3_18