FERMAX 9531 Milo Digital Video Panel Meet Door Lock User Guide
- June 11, 2024
- FERMAX
Table of Contents
FERMAX 9531 Milo Digital Video Panel Meet Door Lock
Product Information
The MILO PANEL is an electronic device designed for use in access control systems. The panel is powered by a 12 Vdc power supply and can be connected to a LAN network through an RJ45 connector. The panel also has an RS485 output for use with specific modules. The device is compliant with Directive 2012/19/EU on waste electrical and electronic equipment.
The device you have purchased is identified under Directive 2012/19/EU on waste electrical and electronic equipment. More info:
CONNECTIONS
-
POWER INPUT: 12 Vdc power supply for the cases where no LAN PoE is available.
-
OUTPUT: Electric lock control relay output.
- NC: Normally closed contact.
- NO: Normally opened contact.
- C: Common.
NOTE: NC & C contacts are internally duplicated.
-
EX PROXIMITY:
- (WD0-WD1) Wiegand input/output.
- (+5V, -) 5 Vdc auxiliar output.
-
EXIT BUTTON /FIRE / DOOR SENSOR:
- (EXIT, -) Connections for indoor button.
- (FIRE, -) Input for fire alarm & block doors unlock contacts.
- (DS, -) Connection for door opened sensor.
-
RS485: Output for Ref.1491 / Ref.1490 / Ref.1494 / Ref.9545 module.
-
RJ 45 NETWORK: RJ 45 LAN connection.
Further information at meet.fermax.com.
BASIC DIAGRAMS
Supply the panel by means of a FERMAX Ref. 4813 (12 Vdc 2A) power supply. Use
a power supply adapted to the electric lock voltage & current. Do not power
the panel and the electric lock from the same power supply.
BASIC PROGRAMMING FROM A PC
- Panel programming is done exclusively by means of a PC connected to the same LAN, through of a web browser (Chrome preferably), accessing the IP of the panel.
- Default IP is: 10.1.0.1
- The PC must have an IP of the same range as the IP of the panel.
Example: In the case that the IP of the panel is 10.1.0.1, the IP of the PC have to be of type 10.X.X.X with a subnet mask 255.0.0.0.
To login, identify yourself with the username and password.
Default value:
- Username: admin
- Password: 123456
- Assign, as a minimum, the parameters indicated in the following table.
- It is necessary to carry out a previous planning of the installation, to define the parameters to assign to each device.
GENERAL
- Panel type: GENERAL or BLOCK
- Panel number: 1-999
- Device number (panels in the same block): 1-99
- Language: Choose from the 10 available languages.
- SIP divert mode: PARALLEL CALL
Confirm with SAVE
NETWORK
Indicate the network parameters assigned to this panel:
- Panel IP address
- Subnet mask
- Gateway
- DNS
Confirm with SAVE
ON-SCREEN INFORMATION
It is possible to get basic information on the equipment configuration through the screen.
- Dial 9999, followed by the bell key.
- The screen will display information about panel settings:
* Firmware version
* GENERAL settings
* Serial number
* MAC
* IP addressNetwork Configuration
To configure the network parameters assigned to the panel, dial 9999 followed by the bell key. The screen will display information about panel settings.
Powering the Panel
The MILO PANEL should be powered using a 12 Vdc power supply, such as the
FERMAX Ref. 4813 (12 Vdc 2A). Ensure that the power supply is adapted to the
electric lock voltage and current, and do not power the panel and the electric
lock from the same power supply.
Connecting to a Network
The MILO PANEL can be connected to a LAN network using an RJ45 connector.
If no LAN PoE is available, use a 12 Vdc power supply.
Configuring the Network Parameters
To configure the network parameters assigned to the panel, dial 9999
followed by the bell key. The screen will display information about panel
settings. You can then enter the network parameters using a PC with an IP
address of 10.X.X.X and a subnet mask of 255.0.0.0.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
For extended information, visit www.fermax.com
Contact: tec@fermax.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>