TREATLIFE ‎SS01S-1 Single Pole Smart Light Switch User Manual

TREATLIFE ‎SS01S-1 Single Pole Smart Light Switch

Introduction

A neutral wire is necessary; only for 2.4G (NOT 5G) Wi-Fi. The wiring procedure will be walked through step-by-step. No hub is necessary; standard size; screwless Snap-On wall plate. a maximum of 1250 W. 10 A output current. Certified by FCC.  Enjoy the convenience of voice control of your home’s lights with Amazon Alexa or Google Assistant hands-free, ideal for times when your hands are full or while entering a dark room. Whether you’re in bed, at work, or on vacation, you can use the smart life app on your smartphone to control the light from anywhere. Schedules can be set up, real-time light status can be seen, devices can be shared, and you can even use your phone to manage a group of lights in your home.

Create timers or countdown plans to program the light to turn on and off according to daily activities or to mimic occupancy while you are away to deceive possible burglars. Reduce the petty things in life, and change the lights whenever you choose. You can effortlessly take advantage of smart home convenience using our smart switch! If there are any sudden quality problems, please let us know as soon as possible and we’ll do everything we can to assist.

Product Outline

Indicator Light Status

Safety Information

Risk Of Electric Shock: Electricity can cause personal injury and property damage if handled improperly, If you are not sure about any part of these instructions, please seek professional assistance from a qualified electrician.

Warnings

• Turn off the power at the circuit breaker and test that power is off before wiring.
• Check supported maximum wattage rating: 1250W
• Replace single pale switch only; DO NOT compatible With 3-way switch.

Prepare Other Tools You’ll Need

• Screwdriver
• Pliers
• Electrical Tester

Installation

Note

• Make sure that the power at the circuit breaker is off before wiring.
• A neutral Wire is required. Confirm that the wall box contains a Neutral Wire (typically white), If the wall box doesn’t have a Neutral Wire, please try another location in your home or call a professional electrician to install the switch.
• The wire colors indicated in this manual are the usual colors and may differ in the same homes.
• Ensure the wire conductors are securely fastened to each wire.
• Ensure the Wi-Fi signal is strong before wiring.
• If you don’t have any wiring experience, please call a professional electrician.

Step 1
Tum off the circuit breaker and use the electrical tester to test the power. Ensure the switch is off before wiring.

Step 2
Remove the existing wall plate; turn on the power at the circuit breaker and use an electrical tester to check which wire is line wire; the tester will flash and/or chirp men it comes close to a line wire. Turn off the power at the circuit breaker and use the electric tester to test if the power is Off, and then pull the existing switch Out; label the line wire and other wires; disconnect the wires from the existing switch with pliers.

Follow the wiring diagram to connect the switch wires to the wires in the wall box with the wire conductors.

Step 3
Mount the switch with the provided screws and snap the wall plate on it.

Step 4
Turn the power back on at the circuit breaker.

Step 5
Switch the light on

Add Devices

1. Download the Smart Life App

2. Registration or Log In

   • Download the “Smart Life” Application.
   • Enter the Register/Login interface; tap “Register” to create an account b/ entering your phone number to get a verification code and “Set password” Choose In” if you already have a Smart Life account.

3. Configure the APP to the Switch
   Preparation: Ensure the switch has connected with ensure your phone has connected to the Wi-Fi router and is able to connect to the internet.
   Note: this switch only supports a 2.4G network. If you have connected 5G network, please disconnect the 5G network first.

   • Tap the “+” icon on the top right corner to add a device, and choose “Wall Switch”.
     

Default Configuration Mode

• Press and hold the manual switch for 5 seconds until the red indicator light blinks quickly.
• Tap “Confirm indicator rapidly blink”; enter Wi-Fi Password; wait for completing the connection.
• Devices have been added successfully.

AP Mode

• If you cannot configure successfully with the default mode, please try to connect with AP Mode.

• Tap “AP Mode” in the top right corner.

• Press and hold the manual switch for 5 seconds, you can see the red indicator light blinks quickly. Then press and hold for 5s again until the indicator light blinks slowly.

• Tap “Confirm indicator slowly blink”.
  

• Enter Wi-Fi Password.

• Open WLAN settings; connect with “SmartLife—xxxx”.

• Back to the App and continue to add the device and wait for completing the connection.

Specifications

Troubleshooting Guide

FCC Caution

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 Of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference including interference that may cause undesired operation.

RSS (Category I Equipment):

This device complies with Innovation, Science, and Economic Development Canada’s license-exempt RSS standard(s). Operation is subject to the following two conditions;

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Frequently Asked Questions

Can I control the smart switch by voice?

Yes, you can control the smart switch by voice with Amazon Alexa or Google Assistant.

Can I connect more than one smart switch to my Wi-Fi network?

Yes, you can connect up to 10 smart switches to your Wi-Fi network.

How many devices can be connected to one smart switch?

You can connect up to 10 devices to one smart switch.

What is the maximum power of each smart switch?

The maximum power of each smart switch is 2200 W.

What is the maximum current output of each smart switch?

The maximum current output of each smart switch is 10 A.

What is a single-pole smart light switch?

A single pole smart light switch is a type of smart switch that is designed to control a light or a group of lights from a single location. It can be installed in place of a standard single pole light switch and allows you to turn your lights on or off, set schedules, or control them remotely using your smartphone or voice assistants like Alexa or Google Assistant.

Does the TREATLIFE Single Pole Smart Light Switch require a neutral wire?

Yes, the TREATLIFE Single Pole Smart Light Switch requires a neutral wire for installation.

What kind of light bulbs can I use with the TREATLIFE Single Pole Smart Light Switch?

The TREATLIFE Single Pole Smart Light Switch works with most types of dimmable LED, CFL, incandescent, and halogen bulbs up to a maximum of 150 watts.

Does the TREATLIFE Single Pole Smart Light Switch require a hub?

No, the TREATLIFE Single Pole Smart Light Switch does not require a hub. It can be connected directly to your home Wi-Fi network and controlled using the TREATLIFE app on your smartphone or tablet.

Can I control the TREATLIFE Single Pole Smart Light Switch with voice commands?

Yes, the TREATLIFE Single Pole Smart Light Switch is compatible with Alexa and Google Assistant, so you can control it with voice commands using your Amazon Echo or Google Home devices.

Can I use the TREATLIFE Single Pole Smart Light Switch in a 3-way switch configuration?

No, the TREATLIFE Single Pole Smart Light Switch is designed for single-pole use only and cannot be used in a 3-way switch configuration.

Is the TREATLIFE Single Pole Smart Light Switch easy to install?

Yes, the TREATLIFE Single Pole Smart Light Switch comes with detailed installation instructions and can be installed easily by following the steps. However, if you are not comfortable with electrical wiring, it is recommended that you hire a professional electrician for installation.

Video – Product Overview

Download The PDF Link;TREATLIFE ‎SS01S-1 Single Pole Smart Light Switch

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>