TREATLIFE DS01-4 Smart Dimmer Light Switch User Manual
- October 30, 2023
- TREATLIFE
Table of Contents
TREATLIFE DS01-4 Smart Dimmer Light Switch
ATTENTION
- The smart dimmer switch is designed for single-pole (one location) wiring. (Not compatible with 3-way/multi-way switch wiring).
- Supported Bulb Types: DimmableLED/CFL – 150W Max; Incandescent – 400W Max. Not compatible with non dimmable light bulbs.
- The neutral wire is required to install the smart switch. If your house was built or remodeled before mid- 80’s, you may not have a neutral. Please try another location or call an electrician for help.
- Install your Treatlife switch where there is a strong Wi-Fi signal.
- Keep your mobile device close to the Treatlife light switch until setup is complete.
The Tools You’ll Need
- Screwdriver
- Pliers
- Electrical Tester
Turn Off Power
Locate your circuit breaker panel and turn off the power to each switch you are replacing
Caution:
Risk of shock. Make sure the power to every switch you are replacing has been turned off before installation. Please call a professional electrician if you are not familiar with electrical work.
Verify Power Is Off
Press each light switch at the location you’re doing the installation to confirm the power is off . If a light turns on, return the panel to turn off the correct circuit. We recommend you remove the faceplate from the old switch and use an electrical tester to test all wires connected to the switch to ensure there is no voltage in the circuit. You may need to turn off more than one circuit breaker.
Pull Out Old Switch
Unscrew the old switch and pull it out of the wall. Do not remove any wires.
Find the NEUTRAL Wires
A neutral is required to install the smart light switch. Make sure there are NEUTRAL wires (most likely a bundle of one or more white wires) in the wall. Unless you are replacing an existing smart switch, it’s probably not connected to your old switch.
Note: If there is no neutral, please try another location or call an electrician for help.
Test NEUTRAL and GROUND Wires
Make sure there is no power on the neutral wires from a neighboring circuit. If necessary, shut off the additional circuits until no voltage is found.
- Label the NEUTRAL and GROUND wire in the wall with the stickers in the package.
GROUND wires are usually BARE COPPER or GREEN.
Identify Line and Load Wire
Label the LINE wire on the wall with the “Line” sticker. Label the LOAD wire in the wall with the “Load” sticker.
How to identify Line and Load?
- Turn on the power and make sure that the switch is off. If not, please turn off the switch and turn off the light. (Be careful not to touch any wires)
- Use an electrical tester to measure the two wires (usually black) connected to the old switch, the Line and Load can be identified according to the measurement method of the electrical tester. (The tester will flash or chirp when it comes close to a Line wire)
Note: If the Line and Load wires are reversely connected, the switch will not work.
Take Pictures of the Wiring
Take one or two pictures of the old switch and where each wire is connected to it, in case you need guidance to repeat the installation.
Note:
Make sure all of the text on the labels in the pictures is clearly displayed.
Remove Existing Switch
Loosen the screw terminals and remove the old switch.
Wire the Smart Switch
Remove the sticker securing the wires on the new switch.
-
Connect NEUTRAL/ GROUND Wires
Use wire nuts to connect the neutral and ground wires on the Treatlife Light Switch to the labeled wires coming from the wall in order. -
Connect LINE/ LOAD Wires
Use wire nuts to connect the line and load wires on the Treatlife Light Switch to the labeled wires coming from the wall in order.
Install a Light Switch Into the Wall
Hold the wire nuts and gently pull each wire to make sure the wire nuts are secure. Carefully push the wires deep into the switch box. Attach the Light Switch to the switch box with the screws provided. Finally, snap on the faceplate
Note: Do not over-tighten the screws, as it could restrict the operation of the switch.
Turn on Power
Turn the power back on at the circuit breaker.
- Press the on/off button to confirm whether the switch is powered on/off normally. If the light fixture can not be turned off/on, the wiring may be incorrect or the nuts are loose. (In this case, the most likely problem is that the line and load wires are reversely connected.) Please refer to the instructions in the manual or call an electrician for help.
If you encounter any problems, please contact us via email: Support@treatlife.tech
(Please be sure to attach the wiring pictures of the old switch in step 7 )
ADD DEVICES
-
Download the TreatLife APP
Please scan the QR code or search 11Treatlife11 on the Apple APP Store / Google Play to download the APP. -
Registration or Log In
Tap “Register” to create an account. Enter your email address to get a verification code and create a password. Or, choose “Log in” if you already have aTreatlife account. -
Configure the APP to the Switch
Preparation: Ensure the switch is connected to power; Ensure your phone is connected to your WiFi router and is able to connect to the internet.
Note: This switch only supports 2.4 GHz networks. If you connected to a 5Ghz network before, please switch to the 2.4Ghz Network
- Tap the icon “+” on the top right corner to Select the Device Type; Tap “All” and choose “Dimmer Switch(WiFi)”.
Default Configuration Mode
- Press and hold the mechanical on/off button for 5 seconds until the red indicator light blinks rapidly.
- Tap “Confirm indicator rapidly blink”; Enter your WiFi Password; Wait for the switch to complete.
- Repeat the steps to add any additional smart switches.
AP Mode
-
If you can not configure the switch successfully with the default mode, please try to connect with AP Mode.
-
Tap “AP Mode” in the top right corner.
-
Press and hold the mechanical on/ off button for 5 seconds, until the red indicator light blinks rapidly. Then press and hold for 5 seconds again until the indicator light blinks slowly.
Tap “Confirm indicator slowly blink”.
-
Enter your Wi-Fi Password.
-
Open WLAN settings; The Wi-Fi settings on your phone and connect to the “Treatli fe- xxx” network.
-
Go back to the APP and continue to add the device then wait for the connection to complete.
Link TreatLife to Alexa/Google Assistant
Go to TreatLife> >More for instructions to link Alexa/Google Assistant.
Note: Please log in with your TreatLife account.
PRODUCT APPEARANCE
Key Steps to Link the Alexa Skill
- Sign in with Amazon, tap on “Skills & Games” in the Alexa menu ;
- Search for “Smart Life”, and tap “Enable” to enable the Skill.
- Enter the “Treatli fe” APP Account and Password, then tap “Link Now” to enable the Skill.
Indicator Light Status
TROUBLESHOOTING
Can’t connect to the APP
- Please make sure the red indicator light is blinking when you are attempting to connect to the APP. Default Mode Paring: Red Indicator Blinking rapidly. AP mode Paring: Red Indicator Blinking slowly.
- Please finish the pairing within 3 minutes when the red indicator starts blinking. (Refer to “Me- FAQ& Feedback” in the APP)
- If your router is 2.4 GHz & 5 GHz dual-band, the 2.4 GHz band may not be turned on. Please enter the router settings to turn on the 2.4 GHz band. You can check the router’s manual or contact the router’s official support for help.
- Make sure you entered the correct WiFi password.
The smart switch shows the wrong status on the APP
- The network may be delayed or the network signal is weak. Try to move the router closer to the switch or power off the router and then power it on. If it still doesn’t work, try to replace the light bulb with a different model or brand bulb.
Can’t connect to Alexa
- Check whether the Alexa APP is correctly configured with the account of the Treatli fe APP. Refer to the manual instruction or “Me- – FAQ&Feedback- – AII- Third-party control issues” in APP to reconnect to Alexa.
The Timing function doesn’t work properly
- Remove the switch from APP, and repair the switch to APP again; You can also check Me-> FAQ & Feedback information in the APP. If it still doesn’t work, please provide the Virtual ID in the APP to us.
Can’t dim lights manually
- Check if they are dimmable light bulbs, if not, change to another non-smart dimmable light bulb.
There is a noise with the light lighting switch or light bulb
- Change to another different model of a non-smart dimmable light bulb.
Lights are too bright even on the minimum level
- Go to Treatlife > dimmer setting to decrease the dimming range.
Lights are too dark or not light up even on the minimum level
- Go to Treatlife > dimmer setting to increase the dimming range.
The lights will flicker
- If they are dimmable light bulbs, go to Treatlife > dimmer setting to switch the mode or adjust the dimming range; If they are not dimmable light bulbs, change to non-smart dimmable light bulbs.
After turning off the light, the light bulb flickers or is not completely turned off.
- Replace the light bulb with a different make/model.
After using the switch for a period of time, the manual operation doesn’t work properly.
- Turn off the power at your circuit breaker panel for a few minutes and then power it on again.
One of several Treatlife light switches doesn’t work properly.
- Replace this switch with one of the known good ones to ensure everything is wired properly. If it still doesn’t work, please contact our support.
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to protect reasonably against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Suppose this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. In that case, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RSS (Category I Equipment)
This device complies with Innovation, Science, and Economic Development Canada’s license-exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
The device is compliant with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance. The minimum distance from the body to use the device is 20cm.
Tech Support: www.treatlife.tech/ pages/support Support@treatlife.tech
FREQUENTLY ASKED QUESTIONS
What is the TREATLIFE DS01-4 Smart Dimmer Light Switch?
The TREATLIFE DS01-4 Smart Dimmer Light Switch is a smart home device that replaces a standard light switch. It allows you to control the brightness of your lights using your voice, smartphone, or home automation system.
What are the key features of the TREATLIFE DS01-4 Smart Dimmer Light Switch?
The key features of the TREATLIFE DS01-4 Smart Dimmer Light Switch include remote control via a smartphone app, voice control compatibility with popular voice assistants, dimming capabilities, scheduling and automation options, and compatibility with existing home automation systems.
How does the TREATLIFE DS01-4 Smart Dimmer Light Switch work?
The TREATLIFE DS01-4 Smart Dimmer Light Switch replaces your standard light switch and connects to your home's Wi-Fi network. You can then control the switch remotely using a smartphone app or voice commands. The switch also allows you to adjust the brightness level of your lights.
Is the TREATLIFE DS01-4 Smart Dimmer Light Switch compatible with voice assistants?
Yes, the TREATLIFE DS01-4 Smart Dimmer Light Switch is compatible with popular voice assistants such as Amazon Alexa and Google Assistant. This allows you to control the switch and adjust the lighting using voice commands.
Can I control multiple TREATLIFE DS01-4 Smart Dimmer Light Switches simultaneously?
Yes, you can control multiple TREATLIFE DS01-4 Smart Dimmer Light Switches simultaneously through the smartphone app or voice commands. This enables you to adjust the brightness of multiple lights or control different areas of your home.
Does the TREATLIFE DS01-4 Smart Dimmer Light Switch require a hub?
No, the TREATLIFE DS01-4 Smart Dimmer Light Switch does not require a separate hub. It connects directly to your home's Wi-Fi network, allowing you to control it using your smartphone or voice assistant.
Can I schedule the TREATLIFE DS01-4 Smart Dimmer Light Switch to turn on/off at specific times?
Yes, the TREATLIFE DS01-4 Smart Dimmer Light Switch offers scheduling capabilities. You can set specific times for the switch to turn on or off automatically, creating personalized lighting routines.
Does the TREATLIFE DS01-4 Smart Dimmer Light Switch work with existing home automation systems?
Yes, the TREATLIFE DS01-4 Smart Dimmer Light Switch is compatible with popular home automation systems such as SmartThings and IFTTT. This allows you to integrate the switch into your existing smart home setup and create customized automation routines.
Does the TREATLIFE DS01-4 Smart Dimmer Light Switch support two-way switches?
Yes, the TREATLIFE DS01-4 Smart Dimmer Light Switch supports two-way switches, also known as three-way switches. This allows you to control the same light or group of lights from multiple switches.
Can I control the TREATLIFE DS01-4 Smart Dimmer Light Switch when I'm away from home?
Yes, you can control the TREATLIFE DS01-4 Smart Dimmer Light Switch remotely when you're away from home. As long as you have an internet connection, you can use the smartphone app or voice commands to control the switch from anywhere.
Does the TREATLIFE DS01-4 Smart Dimmer Light Switch have a physical on/off button?
Yes, the TREATLIFE DS01-4 Smart Dimmer Light Switch typically has a physical on/off button on the switch itself. This allows you to manually control the lights without using the app or voice commands.
Does the TREATLIFE DS01-4 Smart Dimmer Light Switch work with all types of light bulbs?
The TREATLIFE DS01-4 Smart Dimmer Light Switch is compatible with most dimmable LED, CFL, and incandescent light bulbs. However, it may not work with non-dimmable bulbs or certain specialty bulbs. It's recommended to check the product specifications for specific compatibility information.
Can I set different brightness levels for the TREATLIFE DS01-4 Smart Dimmer Light Switch?
Yes, the TREATLIFE DS01-4 Smart Dimmer Light Switch allows you to set different brightness levels for your lights. You can adjust the brightness manually through the app or use voice commands to set specific levels.
Does the TREATLIFE DS01-4 Smart Dimmer Light Switch require a neutral wire?
Yes, the TREATLIFE DS01-4 Smart Dimmer Light Switch typically requires a neutral wire for installation. The neutral wire is necessary to power the switch and enable its smart functionality. It's important to check your electrical wiring to ensure compatibility.
Is professional installation required for the TREATLIFE DS01-4 Smart Dimmer Light Switch?
The installation of the TREATLIFE DS01-4 Smart Dimmer Light Switch involves working with electrical wiring, so it's recommended to hire a licensed electrician for installation. This ensures proper and safe installation of the switch.
VIDEO – OVERVIEW
DOWNLOAD THE PDF LINK:TREATLIFE DS01-4 Smart Dimmer Light Switch User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>