TREATLIFE SS02SH Smart Light Switch User Manual
- June 3, 2024
- TREATLIFE
Table of Contents
TREATLIFE SS02SH Smart Light Switch
ATTENTION
- The Treat|life single pole light switch can only replace existing single pole light switches.
- Neutral wire is required to install the smart switch. If your house was built or remodeled before mid-80’s, you may not have a neutral. Please try another location or call an electrician for help.
- Install your Treatlife where you have a strong Wi-Fi signal.
- Keep your mobile device close to the Treatlife light switch until setup is complete.
- The supported maximum wattage rating is: 1250W.
The Tools You’ll Need
- Screwdriver
- Pliers
- Electrical Tester
Turn Off Power
Locate your circuit breaker panel and turn off the power to each switch you
are replacing
Caution
- Risk of shock.
- Make sure the power to every switch you are replacing has been turned off before installation.
- Please call a professional electrician if you are not familiar with electrical work.
Verify Power Is Off
- Press each light switch at the location youre doing the installation to contirm the power is oft.
- If a light turns on, return the panel to turn off the correct circuit. We recommend you to remove the faceplate from the old switch and use electrical tester to test all wires connected to the switch to ensure there is no voltage in the circuit.
- You may need to turn off more than one circuit breaker.
Pull Out Old Switch
Unscrew the old switch and pull it out of the wall. Do not remove any wires.
Find the NEUTRAL Wires
A neutral is required to install the smart light switch. Make sure there are
NEUTRAL wires (most likely a bundle of one or more white wires) in the wall.
Unless you are replacing an existing smart switch, it s probably not Connected
to your old switch.
Note: If there is no neutral, please try another location or call an electrician for help.
Test NEUTRAL and GROUND Wires
Make sure there is no power on the neutral wires from a neighboring circuit. If necessary, shut oft the additional circuits until no voltage is found.
- Label the NEUTRAL and GROUND wire in the wall with the stickers in the package.
GROUND wires are usually BARE COPPER or GREEN.
Identify Line and Load Wire
- Label the LINE wire in the wall with the “Line” sticker.
- Label the LOAD wire in the wall with the “Load sticker.
How to identify Line and Load?
- Turn on the power and make sure that the switch is off. If not, please turn off the switch and turn off the light. (Be careful not to touch any wires)
- Use an electrical tester to measure the two wires (usually black) connected to the old switch, the Line and Load can be identified according to the measurement method of the electrical tester. (The tester will flash or chirp when it comes close toa Line wire)
Note: If the Line and Load wires are reversely connected, the switch will not work.
Take Pictures of the Wiring
Take one or two pictures of the old switch and where each wire is connected to
it, in case you need guidance to repeat the instalation.
Note: Make sure all of the text on the labels in the pictures is clearly
displayed.
Remove Existing Switch
- Loosen the screw terminals and remove the old switch.
Wire the Smart Switch
Remove the sticker securing the wires on the new switch.
Connect NEUTRAL/GROUND Wires
Use wire nuts to connect the neutral and ground wires on the Treatlife Light
Switch to the labeled wires coming from the wall in order.
Connect LINE/LOAD Wires
Use wire nuts to connect the line and load wires on the Treatlife Light Switch
to the labeled wires coming from the wall in order.
Install Light Switch Into the Wall
Hold the wire nuts and gently pull each wire to make sure the wire nuts are
secure. Carefully push the wires deep into the switoh box. Attach the Light
Switch to the switch box with the screws provided. Finally, snap on the
faceplate.
Note: Do not over tighten the screws, as it could restrict the operation of the switch.
Turn on Power
Turn the power back on at the circuit breaker.
- Press the on/off button to confirm whether the switch is powered on/off normally. If the light fixture can not be tumed off/on, the wiring may be incorrect or the nuts are loose. (In this case, the most likely problem is that the line and load wires are reversely connected.) Please refer to the instructionsin the manual or call an electrician for help.
If you encounter any problems, please contact us via
email: Support@treatlife.tech
(Please be sure to attach the wiring pictures of the old switch in step 7)
the QR code is printed next to the push button on the switch
ADD DEVICES
-
Download the TreatLife APP
Please scan the QR code or search “TreatLife”
on the Apple APP Store/ Google Play to download the APP. -
Registration or Log In
Tap Register” to create an account. Enter your Email Address to get a verification code and create a password. Or, choose “Log in” if you already have a TreatLife account.
Configure the APP to the Switch
Preparation: Ensure the switch is connected to power Ensure your phone is connected to your WiFi router and is able to connect to the internet.
Note: This switch only supports 2.4Ghz networks. If youconnected to a 5Ghz network before, please switch to the 2.4Ghz Network
1OS system paring method
Press and hold the mechanical on/ off button for 5seconds until the red indicator light blinks
- Click on “Proñle”
- Tap HomeKit Information
- Tap “Add Homekit Device” (Make sure the red led indicator is flahing)
- Scan the QR code(the QR code is next to the push button on the switch)
Controlling this HomeKit-enabled accessory automati- cally and away from home requires an Apple TV,an iPad or a Homepod set up as a home hub.The ioS latest version is recommended.
Android system paring method
- Press and hold the mechanical on / off button for 5seconds until the red indicator light blinks.
- Tap “AP Mode” on the top right corner.
- Press and hold the mechanical on/off button for 5 seconds, until the red indicator light blinks rapidly. Then press and hold for 5 seconds again until the indicator light blinks slowly.
- Tap “Confırm indicator slowly blink”.
- Enter your WiFi password.
- Open WLAN settings; The Wi-Fi settings on your phone and connect to the TreatLife-XXX network.
- Go back to the APP and continue to add the device then wait for the connection to complete.
PRODUCT APPEARANCE
Indicator Liaht Status
Link TreatLife to Alexa/Google Assistant
Go to TreatLife> >More for instructions to link Alexa/Google Assistant.
Note: Please log in with your TreatLife account.
- Key Steps to Link the Alexa Skill
- Sign in with Amazon, tap on “Skills & Games” in the Alexa menu;
- Search for the ” TreatLife”, and tap “Enable to enable the Skill.
- Enter the TreatLife APP Account and Password, then tap Link Now to enable the Skill.
TROUBLESHOOTING
Can’t connect to the APP.
-
Please make sure the red indicator light is blinkingwhen you are attempting to connect to the APP.
-
Please finish the pairing within 3 minutes when the red indicator starts blinking. (Refer to “Me-FAQ&
Feedback” in the APP) -
If your router is 2.4Ghz & 5Ghz dual-band, the 2.4Ghz
band may not be turned on. Please enter the router settings to turn on the 2.4Ghz band. You can check the router’s manual or contact the router’s official support for help. -
Make sure you entered the correct WiFi password.
The smart switch shows wrong status on the APP.
The network may be delayed or the signal is weak. Please move the router
closer to the switch or power off the router and then on. If it still doesn’t
work, try to replace the light bulb with a different model/ brand.
Can’t connect to Alexa.
Check whether the Alexa APP is correctly configured with the account of
TreatLife APP
Refer to the manual instruction or check ” Me–FAQ& Feedback–AI-Third-party
control issues in the APP for help.
APP/Alexa is out of sync with light status.
The network may be delayed or the signal is weak, you can try to move the
router closer and restart the router.
The smart switch is turned on or off for no reason.
Please try to power off the switch for a few minutes and then power on, if it
still can not be solved, please provide the Virtual ID in the APP to us.
After using the switch for a period of time, manual operation doesn’t
work properly.
Press the restart button or turn off the power at your circuit breaker panel
for a few minutes and then power it on again.
FCC Caution
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired opera tion. Any
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipmentgenerates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to oorrect the interferenoce by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV techni cian for help.
RSS (Category I Equipment):
This device complies with Innovation, Science, and Economic Development
Canada’s licence-exempt RsS standards). Operation is subject to the following
two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interferenoe that may cause undesired operation of the
device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>