FREDRICK RAMOND FR30106 Jolie LED Linear Pendant Instruction Manual

FREDRICK RAMOND FR30106 Jolie LED Linear Pendant

Product Information

The product is a fixture with item number FR30106. It needs to be assembled by first assembling the main body of the fixture making all necessary electrical connections, hanging the fixture from the ceiling, and then installing the fixture glass. The length of rods required to hang the fixture at the desired height needs to be determined before assembly. The fixture can be mounted to the ceiling by following the mounting instruction sheet (FR30106) provided. After installation, the fixture can be lamped accordingly.

Product Usage Instructions

1. Find a clear area in which you can work.
2. Unpack the fixture from the carton.
3. Carefully review instructions prior to assembly.
4. Before assembly, determine the length of rods required to hang the fixture at the desired height.
5. Assemble the main body of the fixture and make all necessary electrical connections.
6. Hang the fixture from the ceiling using rod sections (B) and attach them to the top of the main fixture body (A).
7. Continue adding sections of the rod until all necessary lengths have been attached to the fixture.
8. After the last stem is installed, remove loop (L) from the canopy by opening the chain link. Remove the loop and thread onto the top of the stem. Now hook loop back onto the chain link and close the link – see Drawing 2.
9. Mount the fixture to the ceiling by following the mounting instruction sheet (FR30106) provided.
10. After installation, lamp the fixture accordingly.

Assembly Instructions

start here

1. Find a clear area in which you can work.
2. Unpack fixture from carton.
3. Carefully review instructions prior to assembly

The construction of this fixture will be accomplished by first assembling the main body of the fixture, making all necessary electrical connections, hanging the fixture from the ceiling and then installing the fixture glass.

Note: It will be necessary to determine the length of rods you will require to hang your fixture at the desired height. After this has been established, please follow the instructions below.

1. Slip first rod section (B) along wire and thread into top of main fixture body (A) .
2. Slip next section of rod (C) along wire and thread into previously installed rod – see Drawing 1
3. Continue adding sections of rod until all necessary length have been attached to the fixture.
4. After last stem is installed remove loop (L) from canopy by opening chain link. Remove loop and thread onto top of stem. Now hook loop back onto chain link and close link – see Drawing 2.
5. Fixture can now be mounted to the ceiling by following the mounting instruction sheet (FR30106) provided.

After fixture is installed it can be lamped accordingly.

mounting instruction

1. To begin installation of your fixture first attach the mounting plate (a) to the junction box (j). This is accomplished by first, threading barrel knobs (b) off of screws (s) in mounting plate (a) that hold the mounting plate (a) to the canopy (c) – see Drawing 1.
2. Remove mounting plate from canopy and remove the appropriate knock outs to allow the mounting plate to be attached to junction box, using screws (d) NOT PROVIDED.
3. NOTE: additional anchor (x) can be used and are recommended. They can be installed through holes (e) of the mounting plate (a). Use appropriate anchors for the material you are anchoring too.
4. Next assembly fixture per instruction sheets provided. Return to this page, to complete the installation of your fixture. to this page, to complete the installation of your fixture.

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE
REQUIREMENTS. Make electrical connections from supply wire to fixture lead wires. Refer to the instruction sheet (I.S. 18) and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to complete the installation of this.

1. After the stems and loop is attached to the canopy, feed the wire through the center hole in loop (g) on the canopy.
2. Now make all electrical connections following the instruction sheet FRIS-18 provided.
3. Hook inspection cable (I) to mounting plate (A) to support fixture during wiring
4. Now slip mounting screws (s) through holes in the canopy (c) and thread on barrel knobs (b) to secure the fixture to the ceiling.

Now follow the glass panel installation instruction sheet provided to complete assembly.

Wiring Instructions for 0-10 volt LED dimmer

start here

Your fixture is designed so it can use a standard incandescent dimmer, Or a 0-10 volt LED dimmer. If a 0-10 volt LED dimmer is used, it may be necessary to have additonal wiring installed from the dimmer switch to the fixture. Consulting an electrician will be necessary

1. If using the optional 0-10 volt dimmer there will be four wires exiting the junction box. (B) Black [+], (W) White [-], wirng are for the 120 / 277 voltage. The (G) Gray {-} and (P) Purple {+} are for the 0-10 volt wires from the dimmer (D) – see Drawing 1.
2. The fixture has four wires of corrisponding colors. When make the wire connections follow the chart below.

Black (B) from junction box (J) wired to Black (B) from fixture (F). White (W) from junction box (J) wired to White (W) from fixture (F). Gray/ Pink(G) from junction box (J) wired to Gray/Pink (G) from fixture (F). Purple (P) from junction box (J) wired to Purple (P) from fixture (F) Connect ground wire from fixture to ground screw on mounting hardware

INCANDESCENT DIMMER USAGE:

If using an incandescent dimmer follow the manufactures instructions.
NOTE: MAKE SURE TO CAP OFF THE GRAY AND PURPLE WIRE FROM THE FIXTURE INSIDE THE CANOPY. IF THEY ARE NOT CAPPED THEY CAN SHORT OUT AND CAUSE THE FIXTURE TO FAIL

IS-SCC [safety cable installation]

start here

WARNING: TO AVOID ELECTRICAL SHOCK, THIS SECTION OF THE INSTRUCTION SHEET IS FOR THE SOLE PURPOSE OF SAFETY CABLE INSTALLATION, AND IS NOT TO BE USED TO MAKE ANY ELECTRICAL CONNECTIONS.

The safety cable must be attached to a ceiling joist or other permanent structure independent of the junction box.

1. using a 3/16″ dia. drill, drill a pilot hole (1). It must be drilled into the permanent structure or through the junction box on the joist side were the safety cable will be attached – see Drawing 1.
2. Insert and thread a 1/4″ hex head lag screw (2) (not included) into pilot hole.
3. Continue installation of this xture according to IS19-50 provided.
4. After length of safety cable is determined, allow enough extra cable so it can be wrapped around lag screw. Thread lag screw to secure safety cable.

Make electrical connections from supply wire to fixture lead wires. Refer to the instruction sheet (I.S. 18) and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to continue the installation of this fixture.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>