eurolite 00129592 LED TMH-S90 Moving Head Spot User Manual

LED TMH-S90 Moving Head Spot
User Manual

LED moving head spot with color wheel, static and rotating gobo wheel, prism and focus
No. 51786075

This user manual is valid for the article number 51786075
You can find the latest update of this user manual in the Internet under:
www.eurolite.de

00129592 LED TMH-S90 Moving Head Spot

DANGER! Electric shock caused by short-circuit
Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric shock when touching the wires. Never open the housing. Keep the device away from rain and moisture.
Please read these instructions carefully before using the product. They contain important information for the correct use of the product.

Every person involved with the installation, operation and maintenance of this device has to
– be qualified
– follow the instructions of this manual
– consider this manual to be part of the total product
– keep this manual for the entire service life of the product
– pass this manual on to every further owner or user of the product
– download the latest version of the user manual from the Internet

INTRODUCTION

Thank you for having chosen one of our products. If you follow the instructions given in this manual, we are sure that you will enjoy this device for a long period of time.

Product features

LED moving head spot with color wheel, static and rotating gobo wheel, prism and focus

• Equipped with a cold white 90 W COB LED
• Positioning within 540° PAN and 200° TILT
• Exact positioning via 16 bit PAN/TILT movement resolution
• Auto, music, master/slave and DMX mode
• Sound-control via built-in microphone
• Color wheel with 7 dichroic color filters and white
• Rainbow effect with adjustable speed in both directions
• Rotating 3-facet prism
• The prism rotates at different speeds
• Gobo wheel 1 with 7 static gobos and open
• Gobo wheel 2 with 6 rotating gobos and open
• All rotating gobos can be interchanged
• Slot-in gobo system for exchanging gobos without tools
• With gobo shake function
• Strobe effect with 2-30 flashes per second
• Internal programs
• Dimmer
• Motorized focus
• Fan-cooled
• Automatic position correction
• Supports QuickDMX – the wireless DMX system from Eurolite
• Built-in phantom-powered USB port for QuickDMX receivers (accessories)
• Control board with LCD and foil-keyboard for adjusting the DMX-starting address, PAN/TILT-Reverse, Program, Reset
• Switch-mode power supply for operation between 100 and 240 volts
• Additional rubber feet when the spot shall be positioned on the floor
• Projection: flicker-free

SAFETY INSTRUCTIONS

WARNING!
Please read the safety warnings carefully and only use the product as described in this manual to avoid accidental injury or damage.
DANGER! Electric shock caused by high voltages
Within the device there are areas where high voltages may be present. Completely disconnect the device from the power supply before you open or remove covers. Mount all covers and attach them firmly before connecting the device again.

Intended use

• This device is an LED moving-head lighting effect for creating decorative effects. This device is designed for professional use in the field of event technology, e.g. on stage. It is not suitable for household lighting.
• Only use the device according to the instructions given herein. Damages due to failure to follow these operating instructions will void the warranty! We do not assume any liability for any resulting damage.
• We do not assume any liability for material and personal damage caused by improper use or noncompliance with the safety instructions. In such cases, the warranty/guarantee will be null and void.
• Unauthorized rebuilds or modifications of the device are not permitted for reasons of safety and render the warranty invalid.

Danger due to electricity

• The device is suitable for indoor use only. Do not use it outdoors. Never expose it to rain or moisture. Do not store it in rooms exposed to moisture.
• To reduce the risk of electric shock, do not open any part of the device. There are no serviceable parts inside the device.
• Only connect the device to a properly installed mains outlet. The outlet must be protected by residual current breaker (RCD). The voltage and frequency must exactly be the same as stated on the device. If the mains cable is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a mains cable. Failure to do so could possibly injure the user.
• The mains outlet must be easily accessible so that you can unplug the device quickly if need be.
• Never touch the mains plug with wet or damp hands. There is the risk of potentially fatal electric shock.
• The mains cable must not be bent or squeezed. Keep it away from hot surfaces or sharp edges.
• Never pull the mains cable to disconnect the mains plug from the mains outlet, always seize the plug.
• Unplug the device during lightning storms, when unused for long periods of time or before cleaning.
• Do not expose the device to any high temperatures, direct sunlight, dripping or splashing water, strong vibrations or heavy mechanical stress.
• Do not place any objects filled with liquids on the device.
• Do not place any open sources of fire, such as burning candles, on or directly next to the device.
• Make sure that objects cannot fall into the device, in particular metal parts.
• Only have repairs to the device or its mains cable carried out by qualified service personnel. Repairs are required when the device or the mains cable is visibly damaged, liquid has been spilled or objects have fallen into the device; when the device has been exposed to rain or moisture, has been dropped or malfunctions occur.
• Cleaning of the device is limited to the surface. Make sure that moisture does not come into contact with any areas of the terminal connections or mains voltage control parts. Only wipe off the product with a soft lint-free and moistened cloth. Never use solvents or aggressive detergents.

Danger to children and people with restricted abilities

• This product is not a toy. Keep it out of the reach of children and pets. Do not leave packaging material lying around carelessly. Never leave this device running unattended.
• This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety.

Warning – risk of burns and fire

• The admissible ambient temperature range (Ta) is -5 to +45°C. Do not operate the device outside of this temperature range.
• The housing temperature (Tc) can be up to 55°C during use. Avoid contact by persons and materials.
• Do not illuminate surfaces within 10 cm of the device. This value is indicated on the device by the symbol.
• Do not use the device near highly flammable materials. Always place the device at a location where sufficient air circulation is ensured. Leave 50 cm of free space around the device. Never cover the air vents of the housing.

Warning – risk of injuries

• Do not look directly at the light source. Persons with light-sensitive epilepsy may suffer from epileptic seizures or fall unconscious.
• Make sure that the product is set up or installed safely and expertly and prevented from falling down. Comply with the standards and rules that apply in your country, in particular EN 60598-2-17.
• If you lack the qualification, do not attempt the installation yourself, but instead use a professional installer. Improper installation can result in bodily injury and or damage to property.
• The manufacturer cannot be made liable for damages caused by incorrect installations or insufficient safety precautions.
• For overhead use, always secure the device with a secondary safety attachment such as a safety bond or safety net.
• Make sure that the area below the installation place is blocked when rigging, derigging or servicing the device.
• For commercial use the country-specific accident prevention regulations of the government safety organization for electrical facilities must be complied with at all times.

Caution – material damage

• This device must not be connected to the mains voltage by means of a dimmer.
• Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects.
• Never switch the device on and off in short intervals. This will considerably reduce the service life of the device.
• If the device has been exposed to drastic temperature fluctuation, do not switch it on immediately. The resulting condensation may destroy the device. Allow the device to reach room temperature before connecting it. Wait until the condensation has evaporated.
• Please use the original packaging to protect the device against vibration, dust and moisture during transportation or storage.
• If a serial number label is affixed to the device, do not remove the label as this would make the warranty void.
• Never lift the fixture by holding it at the projector-head, as the mechanics may be damaged. Always hold the fixture at the transport handles.

DESCRIPTION OF THE DEVICE

1. Lens
2. Projector head
3. Yoke
4. Base
5. Rubber foot
6. Transport handle
7. DMX indicator
8. Error indicator
9. LCD
10. Operating buttons
11. DMX input
12. DMX output
13. USB port for QuickDMX receiver
14. Fuseholder
15. Power switch
16. Power input

INSTALLATION

Inserting/Exchanging gobos

| DANGER!
Install the gobos with the device switched off only. Unplug from mains before!|
---|---|---

If you wish to use other forms and patterns as the standard-gobos, or if gobos are to be exchanged, please follow the instructions below:

| CAUTION!
Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be opened!|
---|---|---

Remove the fixation-ring with an appropriate tool. Remove the gobo and insert the new gobo. Press the fixation-ring together and insert it in front of the gobo.

| Notes!
Slot-in gobo-system for exchanging gobos without tools!
Inserting/Exchanging gobos as described above.|
---|---|---

Rigging
WARNING! Risk of injury caused by falling objects
Devices in overhead installations may cause severe injuries when crashing down. Make sure that the device is installed securely and cannot fall down. The installation must be carried out by a specialist who is familiar with the hazards and the relevant regulation s.

1. Safety-rope
2. Clamp
3. Omega-holders
4. Quick-lock fastener

The device may be placed on the floor or fastened to a truss or similar rigging structure. The device must never be fixed swinging freely in the room.

1. The rigging structure must support at least 10 times the weight of all fixtures to be installed on it.
2. Block access below the work area and work from a stable platform when installing the device.
3. Use rigging hardware that is compatible with the structure and capable of bearing the weight of the device. Please refer to the “Accessories” section for a list of suitable rigging hardware and follow the instructions mentioned at the bottom of the base. Screw one clamp via a M10 screw and self-locking nut onto the Omega-holder. Insert the two quick-lock fasteners of the Omega-holder into the respective holes on the bottom of the device. Tighten the quick-lock fasteners fully clockwise.
4. Secure the device with a safety bond or other secondary attachment. This secondary safety attachment must be sufficiently dimensioned in accordance with the latest industrial safety regulations and constructed in a way that no part of the installation can fall down if the main attachment fails. For the attachment of a safety bond, the supplied eyelet must first be mounted on the device. Install the safety bond by inserting the quick link in the eyelet on the bottom of the base. Pull the safety bond over the trussing system etc. Insert the end in the quick link and tighten the fixation screw. Fasten the safety bond in such a way that, in the event of a fall, the maximum drop distance of the device will not exceed 20 cm.
5. After installation, the device requires inspections periodically to prevent the possibility of rot, deformation and looseness.

CONNECTIONS

DMX512 connection / connection between fixturesThe wires must not come into contact with each other; otherwise the fixtures will not work at all, or will not work properly.
Please note the starting address depends upon which controller is being used.
DMX512 control
A DMX512 data link is required in order to control the device via DMX. The device provides 3-pin XLR connectors for DMX connection.

1. Connect the output of your DMX controller to the DMX input DMX IN of the device with a DMX cable.
2. Connect the DMX output DMX OUT of the device to the DMX input of the next unit in the chain. Always connect one output to the input of the next unit until all units are connected.
3. At the last unit, the DMX cable has to be terminated. Plug the terminator with a 120 Ω resistor between Signal (–) and Signal (+) in the DMX output of the last unit.
4. If the cable length exceeds 300 m or the number of DMX devices is greater than 32, it is recommended to insert a DMX level amplifier to ensure proper data transmission.

XLR connection:

Wireless DMX transmission with QuickDMX
The device features an alternative DMX input for a QuickDMX receiver (sold separately). This connector allows for wireless transmission of DMX control signals to the device. The connector is designed as a USB port which provides the required 5 V operating voltage for the receiver. With QuickDMX devices, extensive cabling between the DMX controller and the device is not required.
Occupation of the USB port:

Connection to the mains
The device uses an auto-range power supply that accepts input voltages between 100 und 240 volts.

1. Connect the device via the enclosed mains cable to a grounded mains socket.
2. Do not connect the unit to the mains voltage via a dimmer. For a more convenient operation, use a mains outlet which is switchable.

OPER ATION

With the power switch, you can switch the device on and off. After you connected the effect to the mains, the device starts running. During the Reset, the motors are trimmed and the device is ready for use afterwards.
The operating modes can be selected by means of the display and the control buttons. All settings remain stored even if the device is disconnected from the mains.
The device has two operating modes. It can be operated in stand-alone mode via the control board or in DMX-controlled mode via any commercial DMX controller and wireless via QuickDMX with the optional available EUROLITE QuickDMX USB Wireless Transmitter/Receiver.
Stand-alone operation
In stand-alone mode, the LED TMH-S90 can be used without controller. Disconnect the LED TMH-S90 from the controller and call up the internal program. Please refer to the instructions under Control Board.
Master/Slave operation
The master/slave operation enables that several devices can be synchronized and controlled by one master device.
On the rear panel of the device you can find an XLR-jack (DMX Out) and an XLR- plug (DMX In), which can be used for connecting several devices.
Choose the device which is to control the effects. This device then works as master device and controls all other slave-devices, which are to be connected to the master device via a DMX cable. Connect the DMX OUT-jack with the DMX IN-plug of the next device.
Set the master device to the desired master mode “Auto1”, “Auto2”, “Auto3”, “Auto4”, “Random” or “Sound”. Set all slave devices to the mode “DMX”. Please refer to the instructions under Control Board.
Control Board
The Control Board offers several features: you can easily set the starting address or run the preprogrammed program.
Press OK 2 x until the display is lit. Browse through the mode menu by pressing the arrow buttons (up and down). Press OK 2 x in order to select the desired menu. Browse through the main menu by pressing the arrow buttons up and down. Press OK to enter the respective menu item of the main menu. You can change the selection by pressing  he arrow buttons (left and right). Press OK in order to confirm. You can leave every mode by pressing the arrow buttons (left and right). The functions provided are described in the following sections.
Default settings shaded.

Mode menu| Main menu| Sub menu|

Function

---|---|---|---
Setting| RunMode| DMX/Sound/Random/ Auto 1, Auto 2,Auto 3, Auto 4| DMX mode / music control / random auto program / auto program 1 – 4
Address| 001~ 512| DMX address setting
Channel| 15 CH| Number of DMX channels
Sens| 1 – 99, 80| Mic sensitivity
Invert – X| ON/OFF| Reverse movement
Invert – Y| ON/OFF
Swap – XY| ON/OFF| PAN-TILT swap
Encoder – XY| ON/OFF| Automatic PAN/TILT adjustment
NoDMX| Keep/clear| Action if no DMX
DisplaySave| ON/OFF| Display turn off
LinearColor| ON/OFF| Switch color change from step to linear color
LoadDefault| OK/Cancel| Restore factory settings
Test| PAN …| PAN = XXX …| Test function
Offset| | | Service function only Password 123456
Advance| InvertDisplay| | Display reverse 180 degrees
TimeReset| | Clear fixture running time
TopTem| 0 – 120, 80| Lamp off at temperature
HardWare| Pan Hall …| | Service function only

SysInfo

| Ver| | Software version
TotalHours| | Fixture running time
PartialHours| | Running time since last switch-on
Temperature| | Inside temperature

Setting
Run Mode
DMX mode
This mode allows the unit to be controlled via any standard DMX controller.
Sound
With this function, you can run the internal program sound-controlled.
Random auto mode
With this function, you can run the random internal program.
Auto mode (Auto 1 – 4)
With this function, you can run 4 different internal programs.
Address
With this function, you can adjust the desired DMX address via the Control Board.
DMX channels
With this function, you can display the number of the DMX channels.
Mic sensitivity
With this function, you can select the desired microphone sensitivity between 0 % and 100 %.
Invert PAN
With this function, you can reverse the PAN-movement.
Invert TILT
With this function, you can reverse the TILT-movement.
PAN-TILT Swap
With this function, you can swap PAN and TILT.
PAN-TILT Encoder / automatic PAN/TILT correction (Feedback)
With this function, you can correct the PAN/TILT movement to the programmed position.
DMX signal / action if no DMX
With this function, you can “keep” or “clear” the DMX value if there is no DMX-signal.
Display power save / display turn off
With this function, you can adjust the display characteristics when the buttons are inactive:
ON – Shuts off the display after 30 seconds
OFF – Display always on.
Linear color / switch color change from step to linear color
With this function, you can select the linear change of the color wheel.
Load default
With this function, you can restore the factory settings of the device. All settings will be set back to the default values (shaded).
Test
Test function of each channel
With this function you can test each channel on its (correct) function.
Advance
Display reverse
With this function, you can flip the display by 180° for a better view when the fixture is hung from the truss or
a ceiling.
Time reset / clear total hours
With this function, you can reset the running time (total hours) of the device.
Top temperature/ LED off at temperature
With this function you can set the inside temperature at which the device will automatically switch the LED off. Inside temperatures below 80° C are not critical. 80° C and more should lead to the LED being switched off. Please note that the outside temperature should not exceed 45° C.
Sys Info
Ver
With this function, you can display the software version of the device.
Total hours
With this function, you can display the running time of the device since the last hours reset under Advance /time reset.
Partial hours
With this function, you can display the temporary running time of the device since the last switch-on of the device.
Show temperature
With this function, you can display the temperature in the projector-head.
DMX operation
Setting the DMX starting address
For operation with a controller with DMX512 protocol, the device is equipped with 15 control channels. To be able to operate the device with a DMX controller, the DMX starting address must be set. The starting address depends upon which DMX controller is being used. Please refer to the controller’s documentation.

1. Press the arrow button left or right to enter the mode menu. Press the OK button.
2. Select Setting with the arrow button up or down.
3. Press the OK button twice.
4. Use the arrow button up or down to select Address and press the OK button to confirm.
5. Use the arrow button up or down to set the DMX starting address. Confirm your setting by pressing the OK button.
6. When DMX control signals are received, the DMX control indicator lights up.

Note: Please make sure that you do not have any overlapping channels in order to control each device correctly and independently from any other fixture on the DMX chain. If several devices are addressed similarly, they will work synchronically.
Functions in DMX mode

head adjustment from one end of the slider to the other (0-255, 128-center). The head can be stopped at any position you wish.
2| | PAN-movement with 16-bit resolution
0| 255| Fine indexing
3| | Vertical movement (TILT)
0| 255| Push slider up in order to move the head vertically (TILT). Gradual head adjustment from one end of the slider to the other (0-255, 128-center). The head can be stopped at any position you wish.
4| | TILT-movement with 16-bit resolution
0| 255| Fine indexing
5| | PAN/TILT speed
0| 255| Decreasing speed
6| | Dimmer intensity
0| 255| Gradual adjustment of the dimmer intensity from 0 to 100 %
7| | Shutter, Strobe
0| 10| No function
11| 255| Strobe-effect with increasing speed
8| | Color Wheel
0| 4| White
5| 9| White + red
10| 14| Red
15| 19| Red + green
20| 24| Green
25| 29| Green + blue
30| 34| Blue
35| 39| Blue + yellow
40| 44| Yellow
45| 49| Yellow + orange
50| 54| Orange
55| 59| Orange+ light blue
60| 64| Light blue
65| 69| Light blue + magenta
70| 74| Magenta
75| 79| Magenta + white
80| 167| Forwards rainbow effect with decreasing speed
168| 255| Backwards rainbow effect with increasing speed
9| | Static gobo wheel, gobo shake
---|---|---
0| 9| Open
10| 19| Gobo 1
20| 29| Gobo 2
30| 39| Gobo 3
40| 49| Gobo 4
50| 59| Gobo 5
60| 69| Gobo 6
70| 79| Gobo 7
80| 89| Gobo 1 shake with increasing speed
90| 99| Gobo 2 shake with increasing speed
100| 109| Gobo 3 shake with increasing speed
110| 119| Gobo 4 shake with increasing speed
120| 129| Gobo 5 shake with increasing speed
130| 139| Gobo 6 shake with increasing speed
140| 149| Gobo 7 shake with increasing speed
150| 202| Gobo wheel rotation backwards with decreasing speed
203| 255| Gobo wheel rotation forwards with increasing speed
10| | Rotating gobo wheel, gobo shake
0| 9| Open
10| 19| Rotating gobo 1
20| 29| Rotating gobo 2
30| 39| Rotating gobo 3
40| 49| Rotating gobo 4
50| 59| Rotating gobo 5
60| 69| Rotating gobo 6
70| 79| Gobo 1 shake with increasing speed
80| 89| Gobo 2 shake with increasing speed
90| 99| Gobo 3 shake with increasing speed
100| 109| Gobo 4 shake with increasing speed
110| 119| Gobo 5 shake with increasing speed
120| 129| Gobo 6 shake with increasing speed
130| 192| Gobo wheel rotation backwards with decreasing speed
193| 255| Gobo wheel rotation forwards with increasing speed
11| | Rotating gobo index, gobo rotation
0| 127| Gobo indexing
128| 190| Forwards gobo rotation with decreasing speed
191| 192| Stop
193| 255| Backwards gobo rotation with increasing speed
12| | Focus
0| 255| Continuous adjustment from far to near
13| | Prism
0| 127| No function
128| 136| 3-facet prism
137| 255| Prism rotation with increasing speed
14| | Internal programs
0| 5| No function
6| 55| Internal program 1
56| 105| Internal program 2
106| 155| Internal program 3
156| 205| Internal program 4
206| 255| Random internal program
15| | Reset
0| 25| No function
26| 76| Reset others
77| 127| Reset PAN/TILT
128| 255| Reset all

CLEANING AND MAINTENANCE

The outside of the device should be cleaned periodically to remove contaminants such as dust etc. The lenses, in particular, should be clean to ensure that light will be emitted at maximum brightness.

1. Disconnect the device from power and allow it to cool before cleaning.
2. Clean the surface with a soft lint-free and moistened cloth. Never use alcohol or solvents as these may damage the surface. Make sure that no liquids can enter the device.
3. The device must be dry before reapplying power.

There are no serviceable parts inside. Do not open the housing. Do not try to repair the device by yourself as this may result in damage. Maintenance and service operations are only to be carried out by authorized dealers.
Should you need any spare parts, please use genuine parts. Should you have further questions, please contact your dealer.
Replacing the fuse
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.

1. Disconnect the device from power and allow it to cool.
2. Open the fuse holder of the mains connection with a fitting screwdriver.
3. Remove the old fuse from the fuse holder and replace it with a new fuse.
4. Carefully push the fuse holder back into its position before reapplying power.

PROTECTING THE ENVIRONMENT

Disposal of old equipment
When to be definitively put out of operation, take the product to a local recycling plant for a disposal which is not harmful to the environment. Devices marked with this symbol must not be disposed of as household waste. Contact your retailer or local authorities for more information. Remove any inserted batteries and dispose of them separately from the product.
You as the end user are required by law (Battery Ordinance) to return all used batteries/ rechargeable batteries. Disposing of them in the household waste is prohibited. You may return your used batteries free of charge to collection points in your municipality and anywhere where batteries/rechargeable batteries are sold. By disposing of used devices and batteries correctly, you contribute to the protection of the environment.

TECHNICAL SPECIFICATIONS

cord with safety plug
Fuse:| 5 x 20 mm, T 2 A
LED:| 1 x COB (chip-on-board) 90 W CW
Max. TILT movement:| Exact positioning (16 bit resolution) 200° Auto position correction (feedback)
Max. PAN movement:| Exact positioning (16 bit resolution) 540° Auto position correction (feedback)
Flash rate:| 2 – 30 Hz
Equipment:| Prism 3-fold; Gobo wheel with rotating gobos rotating; Gobo wheel with static gobos; Focus motor-driven; Color wheel
Color generation:| Color wheel 7 dichroic filters plus open
Gobos:| Gobo wheel with static gobos, 7 gobos and open
Shake effect
Gobo wheel with rotating gobos, 6 gobos and open
Shake effect
DMX channels:| 15
DMX input:| 3-pin XLR (M) mounting version
DMX output:| 3-pin XLR (F) mounting version
Cooling:| Cooling fan
Control:| DMX
Sound to light via microphone
Stand-alone
QuickDMX via USB (optional)
Master/slave function
Beam angle (1/2 peak):| 12°
Housing color:| Black
Width:| 25.0 cm
Height:| 35.0 cm
Depth:| 20.5 cm
Weight:| 5.9 kg

Accessories

Please note: All information is subject to change without prior notice. 29.11.2021 ©

Eurolite is a brand of Steinigke Showtechnic GmbH Andreas-Bauer-Str.
5 97297 Waldbüttelbrunn Germany
D00127139 Version 1.1 Publ. 29/11/2021

References

• Eurolite: Ihre Experten für Licht - Hersteller von Lichteffekten

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>