KARCHER BP 3.200 Home Hydrophore Pump Instruction Manual

BP 3.200 Home
BP 4.900 Home

Register your product
www.kaercher.com/welcome

BP 3.200 Home Hydrophore Pump

General notes

Read these original operating instructions and the enclosed safety instructions before using the device for the first time. Proceed accordingly. Keep both books for future reference or for future owners.

Intended use

This device has been developed for private use and is not intended for the loads imposed by commercial use.
This device is intended for indoor use only.
Note
The pump is not suitable for boosting the existing line pressure.

Permissible feed fluids

Permissible feed fluids:

• Processed water
• Well water
• Spring water
• Rain water
• Swimming pool water with intended dosage of additives

The temperature of the delivered liquid must not exceed 35 °C.

Improper use
Note
The manufacturer accepts no liability for possible damage caused by improper use or  incorrect operation.

Hazard levels

DANGER

• Indication of an imminent threat of danger that will lead to severe injuries or even death.

WARNING

• Indication of a potentially dangerous situation that may lead to severe injuries or even death.

CAUTION

• Indication of a potentially dangerous situation that may lead to minor injuries.

ATTENTION

• Indication of a potentially dangerous situation that may lead to damage to property.

Environmental protection

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.
Electrical and electronic appliances contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which – if handled or disposed of incorrectly – can pose a potential threat to human health and the environment. However, these components are required for the correct operation of the appliance. Appliances marked by this symbol are not allowed to be disposed of together with the household rubbish.
Notes on the content materials (REACH)
Current information on content materials can be found at: www.kaercher.com/REACH

Accessories and spare parts

Only use original accessories and original spare parts.
They ensure that the appliance will run fault-free and safely.
Information on accessories and spare parts can be found at www.kaercher.com.

Scope of delivery

The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

Warranty

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised  customer service site. (See overleaf for the address)

Device description

The maximum amount of equipment is described in these operating instructions. Depending on the model used, there are differences in the scope of delivery (see packaging).
For the illustrations, refer to the graphics page Illustration A

1. Connection adapter with integrated check valve
2. Sealing plug
3. Connection G 1 (33.3mm) suction line (inlet)
4. Filling nozzle with cap
5. Connection G 1 (33.3mm) pressure line (outlet)
6. Connection adapter for pumps G 1
7. ON/OFF switch
8. Pressure indicator
9. Stand with elongated hole for screwing
10. Air valve (car valve) with cap
11. Power supply cable with plug
12. Drain screw

Startup

We recommend using only original Kärcher suction hoses, filter components and hose connections. Using components from other manufacturers can lead to malfunctions when sucking the feed fluid, especially when using bayonet connection systems.

Before initial startup
Preparation

• Before initial startup, check the pressure of the air filling in the storage tank. If necessary, top up to 2.0 bar with a commercially available air pump when switched off/depressurised. Illustration B
• Secure the device against slipping, screw it down if necessary.
• Remove the sealing plug.
• Screw the connection adapter with integrated check valve into the suction connection of the pump (inlet). Illustration C

Note
If the water is dirty, we recommend fitting a pre-filter (see Special accessories) between the check valve and the suction hose. Illustration D

1. Connect vacuum-proof suction hose with integrated backflow stop to suction side. (Available as an special accessory).
2. Screw the connection adapter into the pressure connection of the pump (outlet).
3. Connect the pressure line.
4. Open the filling nozzle cap. Illustration E

• Fill with water until it overflows. Illustration F

• Screw the cap tightly onto the filling nozzle.

• Open existing stop valves in the pressure line.
  Note
  Even minor leaks lead to malfunctions.

• In case of leaks, seal all connections with a suitable sealant (e.g. Teflon tape) to avoid malfunctions due to leakage or air intake.

Permanent installation
In a permanent installation, the pump can be screwed to a suitable surface.

• Screw the pump tightly to a level surface using suitable screws. In addition, in the case of a fixed installation, it is recommended to fit a flexible component on the pressure side, such as a flexible pressure equalization hose (see Special accessories), on the pressure side. This has the following advantages:
• Greater flexibility in erection and installation.
• Sound reduction since no vibration is transmitted in to the pipes of the house water system.
• With smaller leaks, the pump switches less often.
  Note
  In order to simplify the subsequent draining and pressure relief of the system, we recommend the installation of a stop cock between the pump and the pressure line (not included in the scope of delivery). Closing the stop cock prevents water from flowing out of the pressure line when the pump is drained.

Operation

Operation

1. Plug the mains plug into the socket.
2. Switch the device on with the ON/OFF switch.
   Note
   Pump starts immediately. Wait until the pump sucks in and delivers evenly, then close the stop valves in the pressure line. After reaching the switch-off pressure, the pressure switch switches off the motor. The storage tank is now filled, the domestic water supply is ready for operation. If there is no water supply, the switch-off pressure is not reached and the pressure switch can no longer shut off the device. This heats up the water in the pump head. To prevent damage to the pump due to overheating, the power supply is interrupted by the thermal switch in the event of overheating. After cooling down, the power supply is restored.
   Note
   The cooling time until the engine restarts can be up to 150 minutes. We recommend the use of a dry-running protection device (see special accessories) for regular protection against water shortage.
   ATTENTION
   Risk of injury, the system is pressurised!
   When opening a pressurised system, you can be injured by flying parts. Depressurise the device before opening the connections (for pressure, see chapter Technical data) Ending operation 1. Switch off the device at the ON/OFF switch. 2. Unplug the device at the mains plug.

Care and maintenance

DANGER
Danger of electric shock.
Always switch the device off and disconnect the mains plug before working on the device.
The device is maintenance-free.

Pressure relief

1. Open and close connected stop valves for pressure relief.
   The system is depressurised.
   Note
   Rinse the pump with clear water after each use when pumping water with additives.
   Check the pressure of the air filling in the storage tank
   1. Check the pressure of the air filling in the storage tank every six months, if necessary top up to 2.0 bar when the device is switched off/depressurised (unplug the device, open the water tap)
   Note
   The type plate is located below the cover. Unscrew the cover in an anti- clockwise direction. Illustration B

Transport

CAUTION
Risk of injury
Risk of injury from falling device.
When transporting the device, observe the weight of the device (see chapter Specifications) and secure it accordingly when transporting it in vehicles.

Storage

CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.

1. Empty the device completely before storage.
2. Store the device in a frost-protected place.

Special accessories

You will find the possible special accessories on the last page of these operating instructions.

Troubleshooting guide

Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorised Customer Service.

pressure side.
No water available.| 1. Check the water reservoir.
The pump does not start up, or stops suddenly during operation| The power supply is disconnected.| 1. Check the fuses and the electrical connec- tions.
Thermal protection switch in the motor has switched off the pump due to over- heating of the motor.| 1.    Pull out the mains plug.
2.    Allow the pump to cool down.
3.    Clean the suction area.
4.    Prevent dry running.
Note
The cooling time until the motor starts can be up to 150 minutes.
The pump switches itself off and also on again| The thermal protection fuse has switched off the pump to protect it from overheat- ing or switched it on again after it has cooled down.| 1. To prevent recurrence, the system should be checked for leaks and sealed.
Fault| Cause| Rectification
---|---|---
The motor restarts imme- diately after switching off| The pressure in the system is lost.| 1. Check the connections including seals and check for water leakage. The slightest leakage affects operation.
The air pressure in the storage tank is too low.| 1. Fill the storage tank with 2.0 bar (see chap- ter Care and maintenance).
The return valve does not close properly.| 1. Check the check valve on the suction side.
The membrane in the pressure tank is defective.| 1. Have the membrane replaced.
The pump capacity drops or is too low| The suction filter or the check valve (spe- cial accessory) are contaminated.| 1. Clean the suction filter or the check valve (special accessory).
The delivery rate of the pump depends on the delivery head and the connected periphery.| 1. Observe the max. delivery head (see chap- ter Specifications) Select a different hose diameter or a different hose length if nec- essary.
Vibrating noise during water removal| The membrane in the pressure tank vi- brates.| 1. An operating noise that can be eliminated by reducing the pressure of the air filling in the storage tank.

Specifications

0.50 (5.0)
Delivery height (max.)| m| 28| 35
Dimensions and weights|  |  |
Weight (without accessories)| kg| 10,5| 13,9

Note
Reason for exception according to regulation (EU)
2019/1781 Annex I Section 2 (12): (j)
Subject to technical modifications!

Characteristic curves

Declaration of Conformity

EU Declaration of Conformity
We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us. Product: Pump Type: 1.645-xxx

Currently applicable EU Directives
2014/35/EU
2014/30/EU
2011/65/EU
2009/125/EC
Commission Regulation(s)
(EU) 2019/1781
Harmonised standards used
EN 60335-1
EN 60335-2-41
EN 62233: 2008
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 1997+A1: 2001+A2: 2008
EN 61000-3-2: 2014
EN 61000-3-3: 2013
EN IEC 63000: 2018
The signatories act on behalf of and with the authority of the company management.

Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 – 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2021/06/01
Declaration of Conformity (UK)
We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval. Product: Pump Type: 1.645-xxx

Currently applicable UK Regulations
S.I. 2016/1101 (as amended)
S.I. 2016/1091 (as amended)
S.I. 2012/3032 (as amended)
S.I. 2010/2617 (as amended)
Commission Regulation(s)
(EU) 2019/1781
Designated standards used
EN 60335-1
EN 60335-2-41
EN 62233: 2008
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 1997+A1: 2001+A2: 2008
EN 61000-3-2: 2014
EN 61000-3-3: 2013
EN IEC 63000: 2018
The signatories act on behalf of and with the authority of the company management.

Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 – 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2021/06/01

OPTIONAL SPECIAL ACCESSORY

THANK YOU!
MERCI! DANKE! iGRACIAS!
Register your product and benefit from many advantages.
www.kaercher.com/welcome
Rate your product and tell us your opinion.

www.kaercher.com/dealersearch
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28-40
71364 Winnenden (Germany)
Tel.: +49 7195 14-0
Fax: +49 7195 14-2212
http://kaer.ch/er/?l=TwSoJtl9IUOwZyAe1rHDyw

References

• Cher - Official Site
• Cleaning equipment and pressure washers | Kärcher International
• Cleaning equipment and pressure washers | Kärcher International
• Dealer Search | Kärcher International
• Home and Garden Warranty Registration USA - Kärcher

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>