Qlima PGWH1010 Mobile Gas Boiler Shower User Manual

PGWH1010
USER MANUAL

SPECIFICATIONS

PORTABLE GAS WATER HEATER

G301G31: 30 mbar*
13+ butane, 28-30 mbar / Propane, 37 mbar, G30: 28-30 mbar, G31: 37 mbar
Consumption| | 828 gr/h (max.)
| | Countries of destination
FR, BE, IT,|
Min/Max ambient temperature,| | 1/60 °C
Q nom/min| =| 10.5/6.8 KW
P nom/min| =| 9.0/5.8 KW – 5,5 UMIN
pw (max) =10 bar pw(min) = 0,3 bar| | DC 3V
PIN nr. 0063DM7739| |

Distributed in Europe by PVG Holding B.V.
PVG Holding BV, Kanaalstraat 12 C, 5347 KM Oss, the Netherlands
PO. Box 96, 5340 AB OSS, The Netherlands, Qlima.com
Made in P.R.C.

https://www.qlima.com/assortment/water-heating/pgwh1010-2-in-1/

FOR OUTDOOR USE ONLY. Always use a suitable and approved low-pressure regulator. In case of any doubt contact your local dealer. RISK OF DEATH: DO NOT USE IN LEISURE VEHICLES SUCH AS CARAVANS AND AUTO CARAVANS. This appliance requires a hose and gas regulator. Check with your gas supplier. Read the technical and user’s instructions before installation and using the appliance. Change gas container in accordance with the provided instructions. Important: This appliance shall not be fitted to a flue and shall only be used for short delivery periods. This heater is intended and able to operate within the ambient temperature of 1° and 60°C. Do not use it for the supply of drinking water. The use of this appliance in enclosed areas can be dangerous and is PROHIBITED. For use outdoors and in well-ventilated areas.
This water heater is not dedicated for providing (hot) drinking water and is not dedicated for delivering sanitary water. IT – SOLO PER USO ESTERNO. Usare sempre un regolatore a bassa pressione adatto e conforme. In caso di dubbi, contattare il rivenditore locale.

Tabel 1

Tabel 2

DISCLAIMERS GAS HEATERS

Read this user manual carefully before using the appliance and keep it for future reference. Install this device only when it complies with local/national legislation, ordinances, and standards. This product is intended to be used as a portable water heater on camping sites and around residential houses in normal household conditions. Use only outdoors or in well-ventilated areas! Only use this appliance with LPG containers max 15 kg, filled with butane, propane or their mixtures. All as specified on the rating label and the technical paragraph in this manual. Do not use any other gas. Do not use natural gas. It is important that every space where the product is used has sufficient air ventilation as otherwise dangerous situations can occur. No modifications to the safety system are allowed, as that will invalidate the guarantee that the air probe will work properly. Consult your dealer in case of doubt. This appliance requires a hose and a regulator. In case of doubt ask for information from your gas supplier. This appliance is constructed in conformity with the applicable Gas Appliance Regulation (EU) 2016/426 (GAR) and keeping the standard EN26:2015 as a guideline.

WARNINGS

• Read the Directions for Use before using the heater.
• Install the heater according to the instructions as described in the installation section of the directions for use.
• This appliance is manufactured according to CE safety standards. Nevertheless, as with any other device, care must be taken.
• The appliance is only suitable for use in dry, not dusty, locations.
• Do not use in leisure vehicles such as caravans and auto caravans.
• Make sure that the correct gas is used and that the gas containers are not exposed to heat or extreme temperature changes. Always store the gas containers in a cool, dry, and dark place.
• Always use a suitable and approved low-pressure regulator. In case of any doubt contact your local dealer.
• Use the heater only outdoors or in well-ventilated spaces. In this way, the gases produced by combustion will be removed by fresh air.
• Never use the appliance in places where harmful gases or fumes may be present (e.g. exhaust gases or paint fumes).
• WARNING: If the appliance is positioned too close to inflammable materials you may risk a fire.
• For safety reasons take care when children or animals are in the proximity of the appliance, as with any other device, and make sure that children are always aware of the presence of a burning appliance.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• After use closes the gas container.
• Follow the instructions to find any gas leakage as described in these Directions for Use.
• Children should be supervised to ensure that they do not play with the appliance.
• In order to avoid overheating, do not cover the device.
• The device must not be located immediately below a socket outlet.
• The cover of this appliance is intended to prevent direct access to heating elements and must be in place when the heater is in use.
• The cover does not give full protection for young children and infirm persons.
• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.
• Only replace the gas cylinder in a flame-free environment.
• WARNING: Do not move the appliance when in operation.
• WARNING: Make sure to follow these instructions for use. Incorrect use and/or not following the instructions can lead to dangerous situations causing severe injuries to humans and/or serious damage to property.
• Warning: Do not interfere with any of the sealed components.
• Conversion to other gases shall be carried out by a qualified installer, as described in the installation instructions.
• Contact an authorized gas appliance installer for installation, maintenance, and adjusting of the appliance
• Maintenance to this appliance should be done 2 times per year by an authorized gas appliance installer This heater is intended and able to operate OUTDOORS within the ambient temperature 1° and 60°C. Do not use for the supply of drinking water. This water heater is not dedicated for providing (hot) drinking water and is not dedicated for delivering sanitary water. Use only for cleaning materials.
• Use rainwater or water from another natural source such as a lake. Use a pump + filter to supply the water to the heater at the correct pressure and without dirt/pollution. Alternatively, place a water reservoir at a higher level than the water heater in order to have the water coming into the water heater at sufficient pressure.

ASSEMBLING THE APPLIANCE

Before connecting the low-pressure regulator, please follow the instructions provided with the low-pressure regulator.
The manufacturer is not responsible for any harm or damage if attention is not paid to the points described above. Do not twist the flexible tubing or the hose. Gas hose to be minimal 80 cm and max 150 cm. Internal diameter between 8 and 12 mm. Make sure that the gas hose applies to local legislation and standards.

INSTALLATION REQUIREMENTS

• The flame-check window of the water heater shall be at eye level of the user.
• Make sure all electrical lines or electric equipment is at least 400mm away from the appliance in all directions.
• Clearance distances: see fig. 2 and fig. 3.
• The product must be positioned vertical with the gas- and water connections mounted perfectly downwards.
• Make sure the product is fixated thoroughly so it cannot fall.

INSTALLATION METHOD:
Carefully remove your appliance from the box and check the contents for any damage. Mount the product as shown in fig 6.

DIRECTIONS FOR USE

If you have any doubts concerning the heater, please contact qualified service personnel. Keep all packaging material out of the reach of young children. Before connecting the low-pressure regulator, please check and read the following: The appliance should only be powered by propane-butane in a container with a maximum weight of 15 kg. Connect the low-pressure regulator with a fixed calibration of a maximum 30 bar that complies with EN 16129:2013. The hose should be according to national standards. For correct connection, follow the instructions provided with the low-pressure regulator.

• Connect the regulator to the gas container.
• Connect the correct end of the gas hose to the regulator (see fig. 4).
• Connect the other end of the gas hose to the appliance (see fig 4). Use the 3 in 1 multi-country connector if required. (refer to separate delivered picture manual related to the 3 in 1 multi-country connector).

Before connecting the low-pressure regulator to the gas container, make sure that the gas container is closed and that there are no open flames (i.e. a lit oven) in the place where you are working. Connect the low-pressure regulator according to the user instructions that are provided with the low-pressure regulator. Check for gas leaks: see relative section.

• To replace the gas container, make sure that the gas container is closed (follow the user instructions provided with the low-pressure regulator).
• Make sure that there are no open flames or other sources of heat in the area in which you are working.
• Only change the gas cylinder in an amply ventilated area, away from any ignition source (candle, cigarettes, other flame producing appliances, …).
• In addition, it is recommended that the gasket seals of the regulator and the flexible rubber hose be checked to ascertain their condition. If you have any doubt concerning the condition of the hose or the seals, replace them.
• Make sure that you do not damage the connection or any other components.
• Never turn the gas container upside down in order to make full use of the contents. This may release liquid residues left in the container that damage the appliance Irreparably.
• For disconnection or connection of the low-pressure regulator, always follow the user instructions provided with the regulator.
• The manufacturer is not responsible for any harm or damage if attention is not paid to the points described above.
• Do not twist the flexible tubing or the hose.
• Connect the water hose water-in and water-out as shown in fig 7.
• Mount the shower head bracket using the 2 screws provided in the package shown in figure 8.

BATTERY:
Install the two pieces D cell batteries as shown in fig 5. NOTE the “+” and the “–“ to be incorrect position!
Before use: check for any GAS LEAKS

1. Close the gas container.
2. Make sure there is sufficient ventilation.
3. Prepare a bucket of soapy water.
4. Open the gas container.
5. Brush the soapy water on all fittings and connections of the gas circuit.
6. If there is a gas leak, bubbles will rise up from the location of the leak.
7. If a leak is found, close the gas container.
8. Tighten the fitting and the metal rings of the connection.
9. Open the gas container and repeat the procedure again.

USE
For outdoor use only.
WARNING:
Make sure the appliance cannot get wet. Protect from water and rain.

1. Turn the regulation knob on the gas container into the open position.

2. Release the knob and turn it to the position corresponding with the desired amount of heat.

3. Open the water tap.

4. The product is now ready to use.

5. See fig, 1: control panel.
   M = Turn on the appliance with button M
   B = more / less heat/gas
   H = more / less water flow
   WARNING:
   The water from the appliance is maybe very hot. Always carefully check the water temperature. Risk of burned skin!

6. Most hot water: Turn B (gas flow) clockwise to the max. and turn B counterclockwise to min.

7. Reduce the temperature of the water: turn H counterclockwise to min. and turn B clockwise to the max.

8. When Button M is in on position “1” and there is sufficient gas and water flow then the appliance will ignite automatically. During the ignition phase, the light C will light up. The light C will extinguish again when the flames are in full operation.

9. To turn off the device, close the gas container and close the water tap. Switch button M to the “0” position.

10. Turn off the appliance after every use.

WARNING:
Frost will damage the product beyond repair and is not covered by the warranty. In order to prevent freezing damage: drain the water from the appliance after every shower by opening the pressure relief valve K counterclockwise. After draining the water close valve K again.
Do not use the appliance when there is strong wind (only use at <3 Beaufort wind force)

WARNING:
Only use approved gas tubes.
Only use gas tubes between 60 and 150 cm. with a diameter between 8 and 12 mm.
Check the gas tube every 3 months for cracks or leakage. Immediately replace if any cracks or leakages are found.
NEVER cover the appliance!
Keep inflammable, volatile, and/or explosives away from the appliance.
Do not use the water from the appliance as drinking water!
In case of any abnormal burning (smoke, yellow flame, unstable flame, etc) stop the use and contact your local dealer.
Do not touch any part of the Appliance during or shortly after use as the body of the appliance might be hot. Only the turning knobs B and H and the on/off button M.

SWITCH OFF AND DISCONNECT

Additional instructions for disconnecting the hot water geyser in the correct order to prevent (water) damage:

1. Turn off the power switch and remove the batteries.

2. Close the gas bottle and then disconnect the gas pipe.

3. Turn off cold water supply tap.

4. Empty the spray head and the water hose (e.g. in a bucket).

5. Disconnect the cold water supply hose and disconnect the hot water hose(towards the spray head). Allow the device to drain for a while and then mount the sealing caps back on the pipes.
   CAUTION: the device may still contain water. When disconnecting the cold and hot water pipe, this water will flow out!

6.  Let the unit and the accessories dry. Store everything when it’s dry in the original packaging.

MAINTENANCE

1. Switch off the appliance and close the valve on the gas container. Allow it to cool down for at least 10 minutes before cleaning it.
2. Keep the appliance clean. Remove any dust and other dirt with a damp cloth. Use regular cleaning products for stubborn stains. Clean the heater thoroughly two times a year.
3. Inspect it each time before using it. Use a mixture of soapy water and water to check the connections for leaks. If any bubbles occur, there is a leak. It should be repaired immediately.
4. Check the hose/regulator connection each time before using it. If the horse shows any sign of wear and tear or has any cracks, it should be replaced immediately.
5. The appliance should be inspected by a certified service station once a year. The appliance should not be installed and/or used in rooms.
6. The appliance maintenance operations are necessary to enable it to be put back into service after these devices have operated.
7. If this device or one of its parts are dismantled previously existing seals shall be remade.
8. Only the manufacturer’s original parts should be used for replacements.
9. WARNING: The safety device shall not be put out of operation. Inappropriate interference with the safety device can cause serious injuries and/or damage.

If you fail to consult and/or follow up the rules, instructions, and explanation, the warranty will no longer be valid, and the manufacturer will no longer deal with any damage to the appliance and/or your environment under the warranty. The use of this product and the elements required for that purpose is entirely at the end user’s own risk.

TROUBLESHOOTING

No flame/no ignition in winter
(temp. <7 °C)| Check whether butane or propane is being used: butane will burn even more poorly as the temperature drops below 7 °C because it then turns into liquid. With LPG (=propane/butane mixture), it will often help to give the gas cylinder a shake.
No flame| – Too low water flow. Solution: Increase water flow.
– Too low water pressure. Solution: Increase water pressure to a pressure > 0.03 MPa.
– The pressure relief valve is open. Solution: Tighten the pressure relief valve by turning the valve clockwise.
– Not enough gas: Exchange gas bottle.
Yellow flame instead of blue flame| Contact the service center immediately for help.

Reasons \ Troubles| The
flame
goes out| No ignition after opening water valve| Ticking noise in the ignition| Yellow flame| Abnormal smell| Low water temperature under
highest
temperature setting| Extremely hot
temperature under highest
temperature setting| Burning after closing
the water valve| The indicator light is on| The lowest possible water outlet
temperature from the geyser remains too high.| Solutions
---|---|---|---|---|---|---|---|---|---|---|---
Gas valve not open| | •| | | | | | | •| | Turn on the main valve or replace the gas cylinder
Gas valve half-open| •| | | | | •| | | | | Turn on the main valve
pressure gas| High| | | | | | | | | •| | Contact the repairer to check the gas pressure valve
Low| •| | | | | •| | |
Coldwater valve closed| | •| | | | | | | | | Turn on the water supply main valve
Freezing| | •| | | | | | | | | Use after defrosting
Inadequate water supply| •| •| | | | | •| | •| •| Call repairer to check water pressure, then clean the filter
Water temperature control mistake| | | | | | | •| •|  •| | Turn the temperature and gas rods properly
Insufficient fresh air| •| | | | •| | | | | | Open the ventilation hole to let enough fresh air in
shortage| •| •| | | | | | | | | Replace the batteries
series
Burner clogged| | | | •| •| | | | | | Contact the service center

STORAGE INSTRUCTIONS

If it is decided that the appliance is not to be used anymore, it is recommended that it be disconnected from the gas container. Also, cut the rubber hose. If children play with the appliance, make sure that dangerous parts are removed. Never dispose of nonbiodegradable products in the environment, but dispose of them in accordance with current national legislation.

GUARANTEE CONDITIONS

The appliance is supplied with a 24-month guarantee, commencing on the date of purchase. All material and manufacturing defects will be repaired or replaced free of charge within this period. The following rules apply:

1. We expressly refuse all further damage claims, including claims for collateral damage.
2. Repairs to or replacement of components within the guarantee period will not result in an extension of the guarantee.
3. The guarantee is invalidated if any modifications have been made, no genuine parts are fitted or repairs are carried out by third parties.
4. Components subject to normal wear, such as filters, batteries, lamps, and heating elements are not covered by the guarantee.
5. The guarantee is valid only when you present the original, dated purchase invoice and if no modifications have been made.
6. The guarantee is invalid for damage caused by neglect or by actions that deviate from those in this instruction booklet.
7. Transportation costs and the risks involved during the transportation of the appliance or components of the appliance shall always be for the account of the purchaser
8. Damage caused by not using suitable spare parts is not covered by the guarantee. To prevent unnecessary expense, we recommend that you always first carefully consult the instructions for use. Take the appliance to your dealer for repairs if these instructions do not provide a solution.

www.Qlima.com

If you need information or if you have a problem, please visit our website (www.qlima.com) or contact our sales support (T: +31 412 694 694).
PVG Holding BV – Kanaalstraat 12 C – 5347 KM Oss – the Netherlands
P.O. Box 96 – 5340 AB Oss – the Netherlands
Marcom mvz©220112 man_PGWH1010 (‘22) V1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>