SMART MEDIA SOLUTIONS M000284 SMS Presence W/F Motor Presence W/F Motor VC Instruction Manual
- June 9, 2024
- SMART MEDIA SOLUTIONS
Table of Contents
SMART MEDIA SOLUTIONS M000284 SMS Presence W/F Motor Presence W/F Motor VC
Instruction Manual
K05-142-22 / K05-142-62 SMS Presence W/F Motor 600×400 EU DG
K05-144-22/ K05-144-62 Presence W/F Motor VC 120 800×400 EU DG
K05-143-22 / K05-143-62 SMS Presence W/F Motor 1000×600 EU DG
K05-145-22/ K05-145-62 Presence W/F Motor VC 120 1000×600 EU DG
Instructions for Mounting
Warning
A correct mounting is extremely important and this is not the responsibility
of SMS Smart
Media Solutions AB. Faulty mounting may result in injury to persons or damage to equipment. SMS will not be responsible in any way if the product has been mounted incorrectly.
Mounting fittings are not included with the product for reasons of safety,
since the
properties and bearing strength of walls/ceilings are specific for each case.
Suitable mounting fittings must be selected based on the material of the
wall/ceiling. Obtain advice from a specialist in the field or from a
specialist shop concerning the choice of mounting fittings. It is the
responsibility of the installer to ensure that the wall/ceiling can support at
least four times the combined weight of the screen/projector and bracket.
The maximum load for this product is given in the table in these installation instructions. The instructions for installation and use of the screen/projector must also be followed with respect to the location and attachment of the screen/projector.
Warranty terms and conditions
- SMS guarantees that a product that SMS has determined to be defective as a result of deficient manufacture or material will be repaired or – if necessary – replaced, without cost, on condition that a claim is made within the period of warranty, which is 2 years. The guarantee does not apply for normal wear and tear.
- In the event of a claim being made under the terms of the warranty, the product and the original purchase receipt are to be returned to SMS. The name of the supplier and the date of purchase mustbe clearly legible on the receipt. The owner is to pay the cost of returning the product to SMS, while SMS is to pay the cost of returning the product subsequently to the owner.
- The warranty provided by SMS does not apply under the following conditions:
- if the product has been drilled, mounted and/or used in any way that is not in accordance with the instructions for use, or if it has been mounted using inappropriate mounting fittings.
- if the product has been modified or repaired by anyone other than SMS.
- if the defect has arisen as a result of external factors (that are not associated with the product), such as lightning strike, water damage, fire, mechanical scratching, storage at extreme temperatures, weather conditions, solvents or corrosive agents, faulty use, or carelessness.
- if the product has been used for equipment other than that specified on the packaging.
Declaration of conformity
Manufacturer: SMS – Smart Media Solutions AB
Hästholmsvägen 32, 5th Floor
SE-131 30 Nacka
Sweden
hereby declares that:
SMS Presence Mobile/Floor Motor Flipster
model series K05-1xx
has been manufactured such that it conforms to
the following EU directives:
·the Machinery Directive 2006/42/EC
·the EMC Directive 2014/30/EU
·the Low Voltage Directive 2014/35/EU
Nacka 08-01-2020 **
**
Instructions for use – SMS Presence W/F Motor
When using
When using the product connect the mains plug
Maximum display weight
ASSEMBLY INSTRUCTIONS
YOU WILL NEED
NOT INCLUDED
NUMBER OF PERSONS REQUIRED
**LIST OF PARTS
**
LIST OF PARTS (cont.)
Adjust position and depth of bracket
Mark drill holes (8x)
Drill holes (8x)
Bolt bracket to wall& floor
Check level before proceeding
Slide B3 (2x)
Mount with B4 (8x)
Mount remote control bracket
Cable chain setting
Guide cable
Guide cable & mount remote control
For SMS Presence W/F Motor VC only
For SMS Presence W/F Motor VC only
Attach middle (D2) & bottom (D3) covers
(For procedure to open/ close bottom cover see page 24, step 20)
Mount bracket on display
Mount display
Adjustment & Alignment
Camera shelf and camera Installation
To open or close bottom covers
Use this space to store cables, codecs, accessories, etc.
To move display UP or DOWN
Refer page 25 for procedure for setting motor to zero
SET MOTOR TO ZERO (optional)
Before setting motor to zero, loosen screws (4x) as shown
Set height motor Run to to zero
After setting motor to zero, tighten screws (4x) as shown
PRODUCT DIMENSIONS
SMS Evoko Group AB
Hästholmsvägen 32, 5th floor, SE-131 30 Nacka, Sweden
www.smartmediasolutions.com
2021-02-16 Doc no: M000284 Rev. A We reserve the right to introduce changes in the product specifications after the publishing of this docume
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>