StarTech com ARMQUADPS Quad Monitor Mount User Manual
- June 9, 2024
- StarTech com
Table of Contents
ARMQUADPS Quad Monitor Mount
Product Information
- Product Name: Quad Monitor Mount | Full Motion | Premium
- SKU#: ARMQUADPS
- Actual product may vary from photos
- For the latest information and specifications visit www.startech.com/ARMQUADPS
- Manual Revision: 01/21/2022
Specifications
- Type of Measurement: VESA Mounting Hole Pattern
- VESA Mounting Hole Pattern: 75×75, 100×100
- Tilt: +900 to -150
- Screen Size: Maximum 30 in. (762 mm)
- Rotate: Full Motion
- Swivel: Yes, with arm extension
- Weight/Load Capacity: 145kg
Package Contents
- Quad Monitor Mount with Support Pole and C-Clamp Base
- Monitor Mount (x4)
- Swivel Arm (x8)
- Swivel Arm Shoulder (x2)
- Cable-Management Clip
Installation Instructions
Using the Grommet Mount
- Place the support pole through the center hole of the grommet mount base.
- Insert the grommet mount into the desired location on the desk and tighten the screw on the underside of the desk to secure it in place.
- Attach the monitor mount to the support pole by sliding it onto the pole and securing it with the included screws.
- Attach the swivel arms to the monitor mount and adjust them to the desired position.
- Attach the monitors to the swivel arms using the VESA mounting holes.
Using the C-Clamp
- Place the support pole through the center hole of the c-clamp base.
- Place the c-clamp onto the desired location on the desk and tighten the screw on top of the c-clamp to secure it in place.
- Attach the monitor mount to the support pole by sliding it onto the pole and securing it with the included screws.
- Attach the swivel arms to the monitor mount and adjust them to the desired position.
- Attach the monitors to the swivel arms using the VESA mounting holes.
Attaching and Removing Monitors
- Attach the monitors to the swivel arms using the VESA mounting holes and ensure they are securely in place.
- To remove a monitor, gently pull it away from the swivel arm and lift it off of the VESA mounting plate.
Adjusting Monitor Tilt and Routing Cables
- To adjust the tilt of a monitor, use the tilt adjustment mechanism located on the side of the monitor mount.
- To route cables, use the included cable-management clip to secure them along the support pole and swivel arms.
Compliance Statements
Use of Trademarks, Registered Trademarks, and other Protected Names and
Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way
to StarTech.com. Where they occur these references are
for illustrative purposes only and do not represent an endorsement of a
product or service by StarTech.com, or an endorsement of the product(s) to
which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document,
StarTech.com hereby acknowledges that all trademarks,
registered trademarks, service marks, and other protected names and/or symbols
contained in this manual and related documents are the property of their
respective holders.
Warning Statements
- Make sure that you assemble this product according to the instructions.
- Do not exceed the weight capacity of this product. Overloading this product might result in injury or property damage. This product can support the following weight: 99.2 lb. (45 kg).
- This product is intended for indoor use only and should not be used outdoors.
Safety Statements
Safety Measures
- Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
Product Diagram
- Monitor Mount (x 4)
- Swivel Arm (x 8)
- Swivel Arm Shoulder (x 2)
- Support Pole
- C-Clamp
- Cable-Management Clip
Product Dimension
Product Rotation 
Product Information
Specifications
| Type of Measurement | Measurement |
|---|---|
| VESA Mounting Hole Pattern | 75×75 |
100×100
Tilt| +900 to -150
Screen Size| Maximum 30 in. (762 mm)
Rotate| 3600
Swivel| 3600
Weight/Load Capacity| 99.2 lb. (45 kg)
Arm Extension| 16.53 in. (420 mm)
Package Contents
Installation
Using the Grommet Mount
-
Align the Mounting Holes in the Grommet Base with the Mounting Holes on the Support Pole.
-
Insert four M5 x 14 mm Screws through the Mounting Holes on the Grommet Base and into the Mounting Holes on the Support Pole.
-
Using the M3 Hex Keys, tighten the four M5 x 14 mm Screws. Attaching the Grommet Base to the Support Pole
-
Slide the four Pegs on the Decorative Plate (attached to the Support Pole) into the four Peg Holes on the Grommet Base.
-
Remove the backing from the EVA Pad and apply the adhesive side of the EVA Pad to the bottom of the Grommet Base, to cover the four M5 x 14 mm Screws to protect the mounting surface.
-
You need to remove one of the Hand Screws from the Lower Base to use with the Grommet Base. Use a Phillips Head Screwdriver (sold separately) to remove the Screw from the Hand Screw on the Lower Base.
-
Slide the Grommet Clip over the Hand Screw.
-
Align the Support Pole with Grommet Assembly with the Grommet Hole on the Mounting Surface.
Note: The size of the Grommet Hole should be between .39” – 3” (10 – 80 mm).
The thickness of the Mounting Surface should be between .78” – 1.7” (20 – 45 mm).
-
Insert the Hand Screw with Grommet Clip through the Grommet Hole in the Mounting Surface and into the Grommet Base.
-
Hand tighten the Hand Screw, securing the Support Pole in place.
Using the C-Clamp
-
Align the Mounting Holes in the Upper Base of the C- Clamp with the Mounting Holes on the Support Pole.
-
Insert four M5 x 14 mm Screws through the Mounting Holes on the Upper Base and into the Mounting Holes on the Support Pole.
-
Using the M3 Hex Key, tighten the four M5 x 14 mm Screws.
-
Slide the four Pegs on the Decorative Plate (attached to the Support Pole) into the four Peg Holes on the Upper Base.
-
Remove the backing from the EVA Pad and apply the adhesive side of the EVA Pad to the bottom of the Upper Base, covering the four M5 x 14 mm Screws to protect the mounting surface.
-
Measure the width of the mounting surface and adjust the width of the C-Clamp by aligning the holes on the Lower Base with the holes on the Upper Base.
-
When the desired width is achieved, insert the six M5 x 14 mm Screws through the Lower Base and into the Upper Base.
Note: The thickness of the mounting surface must be be-tween .79” – 3.5” (20 mm – 90 mm). -
Use the M3 Hex Key to tighten the M5 x 14 mm Screws.
-
While supporting the weight of the Support Pole slide the C- Clamp over the edge of the mounting surface.
-
Using the Hand Screws tighten the C-Clamp until the C- Clamp is pressed tightly against the mounting surface.
Attaching the Monitor Mount
When the Desk Mount has been mounted to the mounting surface either by using
the C-Clamp or Grommet:
- Slide two of the Cable Management Clip onto the Support Pole.
- Position the second Cable Management Clip at the (approximate) height you want the first row of Monitor to sit.
- Tighten the Cable Management Clip using the Adjustment Screw located on the side of the Cable Management Clip, using the M3 Hex Key. Be careful not to over-tighten the Cable Management Clip.
- Slide the Swivel Arm Shoulder onto the Support Pole, so that it is resting on the second Cable-Management Clip.
- Tighten the Swivel Arm Shoulder using the Adjustment Screw located on the side of the Swivel Arm Shoulder, using the M3 Hex Key. Be careful not to over-tighten the Swivel Arm Shoulder.
- Repeat steps 1 – 4 to install the second Swivel Arm Shoulder.
- Slide the Mounting Hole on Swivel Arm 1 over the Mounting Peg on the Swivel Arm Shoulder until it clicks into place.
- Repeat step 7 to install Swivel Arms 2, 3, and 4.
- To install the second row of Swivel Arms (5, 6, 7, and 8), slide the Mounting Hole on Swivel Arm 5 over the Mounting Peg on Swivel Arm 1 until it clicks into place.
- Repeat step 9 to install Swivel Arms 6, 7, and 8.
Attaching a Monitor Using the VESA Mount
-
Align the Mounting Holes (x 4) on the Monitor Mount with the mounting holes on the back of the Monitor.
Note: When mounting the VESA mount the orientation of the Monitor is important. -
Insert the Thumb Screws through the Monitor Mount and into the back of the Monitor.
-
Using your fingers, tighten the Thumb Screws.
Warning! Do not over-tighten the Thumb Screws. If you encounter resistance while you are tightening the Thumb Screws, stop tightening. Failure to do so could result in dam-age to the monitor. -
Complete steps 1 – 3 to mount the remaining Monitors.
Attaching the Monitor Mount
Note: Attaching the Monitor Mount may require two people.
- While supporting the weight of the Monitor, carefully slide the Mounting Hole on the Monitor Mount over the Mounting Peg on the Swivel Arm until it clicks into place.
- Using the Hex Keys, adjust the swivel tension of the Monitor Mount by loosening or tightening the Hex Screws located on the Monitor Mount next to the Mounting Hole.
- Repeat Steps 1 – 2 to attach the remaining Monitor Mounts.
Removing the Monitor Mount
- Slide the Thumb Clip to disengaging the locking mechanism.
- While holding the Thumb Clip and the weight of the Monitor Mount, lift the Monitor Mount up, sliding the Mounting Peg out of the Mounting Hole.
Adjusting the Monitor Tilt
- While supporting the weight of the Monitor, use the Hex Key (included) to loosen or tighten the Hex Screw on the side of the Monitor Mount, until the tension can hold the weight of the Monitor but it is still adjustable.
Note: The screw cap located on the opposite side of the Hex Screw is not used for tilt adjustments.
Routing the Cables
The Monitor Mount comes with a Cable-Management System that can be used to
run the monitor cables down the mounting arms.
Note: Make sure that the cables are unplugged before you route them through the Cable-Management System.
- Thread the Cable through the hole in the Swivel Arms.
- Run the Cable through the Cable-Management Clip on the side of the Support Pole.
- Repeat steps 1 – 2 for any additional Monitors.
Warranty Information
This product is backed by a ten-year warranty.
For further information on product warranty terms and conditions, please refer
to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP
(or their officers, directors, employees or agents) for any damages (whether
direct or indirect, special, punitive, incidental, consequential, or
otherwise), loss of profits, loss of business, or any pecuniary loss, arising
out of or related to the use of the product exceed the actual price paid for
the product.
Some states do not allow the exclusion or limitation of incidental or
consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan.
It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need.
From the latest technology to legacy products — and all the parts that bridge
the old and new — we can help you find the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they
need to go. Just talk to one of our tech advisors or visit our website. You’ll
be connected to the products you need in no time.
Visit www.startech.com for complete information on
all StarTech.com products and to access exclusive resources and time-saving
tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and
technology parts. StarTech.com was founded in 1985 and
has operations in the United States, Canada, the United Kingdom and Taiwan
servicing a worldwide market.
Reviews
Share your experiences using StarTech.com products, including product
applications and setup, what you love about the products, and areas for
improvement.
StarTech.com
Ltd.
45 Artisans
Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com
LLP
4490 South
Hamilton Road
Groveport, Ohio
43125
U.S.A.
StarTech.com
Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com
Ltd.
Siriusdreef 17-27
2132 WT
Hoofddorp
The Netherlands
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>