AVer PTZ310 Professional PTZ Camera Control User Manual
- June 5, 2024
- AVer
Table of Contents
KARCHER WD 1 vacuum cleaner Compact Battery
Product Introduction
Overview
| (1) Camera lens | (5) PoE+ port | (9) mini-USB port |
|---|---|---|
| (2) IR sensor | (6) RS232 port | (10) HDMI port |
| (3) LED indicator | (7) RS422 port | (11) 3G-SDI port |
| (4) Kensington lock | (8) Audio in* | (12) DC Power jack |
- Line input level: 1Vrms (max.).
- Mic input level: 50mVrms (max.); Supplied voltage:2.5V
RS232 and RS422 Connection
Connect through the RS232 or RS422 for camera control.
RS232
RS232 Port Pin Definition
Function
| Mini DIN9 PIN #| ****
I/O Type
| ****
Signal
| ****
Description
---|---|---|---|---
VISCA IN
| 1| Output| DTR| Data Terminal Ready
2| Input| DSR| Data Set Ready
3| Output| TXD| Transmit Data
6| Input| RXD| Receiver Data
VISCA OUT
| 7| Output| DTR| Data Terminal Ready
4| Input| DSR| Data Set Ready
8| Output| TXD| Transmit Data
9| Input| RXD| Receiver Data
5| —| —| Not connect
RS232 mini DIN9 to mini DIN8 Cable Pin Definition
Mini DIN8 Cable Pin Definition
| No. | Signal |
|---|---|
| 1 | DTR |
| 2 | DSR |
| 3 | TXD |
| 4 | GND |
| 5 | RXD |
| 6 | GND |
| 7 | NC |
| 8 | NC |
Din8 to D-Sub9 Cable Pin Definition
RS422
[Note] Use cat5e splitter for multi-camera connection.
RS422 Pin
No.| Pin| No.| Pin
1| TX-| 5| TX+
2| TX+| 6| RX+
3| RX-| 7| RX-
4| TX-| 8| RX+
Cat5e splitter pin assignment:
OSD Tree
Camera
Go to Advanced Setting -> Control. Make sure the Camera Address, Baud Rate
setting is correct.
Advanced Setting
Advanced Setting| Audio| |
---|---|---|---
| Input Type| Mic in/Line in|
|
Auto Gain Control| Off/On|
|
Noise Suppression| Off/On|
|
Audio Volume| 0 ~ 10|
|
Control|
Protocol| VISCA/Pelco D/Pelco-P/AW|
|
Camera Address| 1~7|
|
Baud Rate| 2400/4800/9600/38400|
|
Smart Framing| Off/On|
Smart Shoot| Off/On|
Number of block| 2/3/4|
Initial Position| Preset 6/Preset 7/Preset 8/Preset 9|
Time to back initial position| 5s/10s/15s/20s/25s/30s/35s/40s|
RS232/422 Visca Command Table
| Command Set | Command | Command Packet | Comments |
|---|---|---|---|
| IF_Clear | Broadcast | 88 01 00 01 FF | I/F Clear (Clear Visca connection) |
| CAM_Power | On | 8x 01 04 00 02 FF | Power ON/OFF (Power On supported in Standby |
mode only)
Off| 8x 01 04 00 03 FF
CAM_Zoom
| Stop| 8x 01 04 07 00 FF|
Tele (Standard)| 8x 01 04 07 02 FF|
Wide (Standard)| 8x 01 04 07 03 FF|
Tele(Variable)| 8x 01 04 07 2p FF| p=0 (Low) to 7 (High)
Wide(Variable)| 8x 01 04 07 3p FF
CAM_Zoom| Direct| 8x 01 04 47 0p 0q 0r 0s FF| pqrs: Zoom Position， PTZ310:
0x0000~0x6f20 PTZ330: 0x0110~0x5490
CAM_DZoom| On| 8x 01 04 06 02 FF| Digital zoom ON/OFF
CAM_DZoom| Off| 8x 01 04 06 03 FF
CAM_Focus
| Stop| 8x 01 04 08 00 FF|
Far(Variable)| 8x 01 04 08 2P FF| p=0 (Low) to 7 (High)
Near(Variable)| 8x 01 04 08 3P FF|
Far (Standard)| 8x 01 04 08 02 FF|
Near (Standard)| 8x 01 04 08 03 FF|
Direct| 8x 01 04 48 0p 0q 0r 0s FF| pqrs: Focus Position，0x0000(wide) ~
0x4000(tele)，
Auto Focus| 8x 01 04 38 02 FF|
Manual Focus| 8x 01 04 38 03 FF|
One Push| 8x 01 04 18 01 FF|
CAM_Focus| Auto/Manual| 8x 01 04 38 10 FF|
AF_Sensitivity| Normal| 8x 01 04 58 02 FF| AF Sensitivity Normal/Low
AF_Sensitivity| Low| 8x 01 04 58 03 FF|
CAM_AFMode| Normal AF| 8x 01 04 57 00 FF| Continous AF ON
CAM_AFMode| Zoom Trigger AF| 8x 01 04 57 02 FF| Continous AF OFF, only trigger
AF after zoom in/out
CAM_ZoomFocus| Direct| 8x 01 04 47 0p 0q 0r 0s 0t 0u 0v 0w FF| pqrs: Zoom
Position
tuvw: Focus Position
CAM_WB
| Auto| 8x 01 04 35 00 FF| Normal Auto
Indoor| 8x 01 04 35 01 FF| Indoor mode
Outdoor| 8x 01 04 35 02 FF| Out door mode
One Push WB| 8x 01 04 35 03 FF| One Push WB mode
Manual| 8x 01 04 35 05 FF| Manual Control mode
One Push| 8x 01 04 10 05 FF| One Push WB Trigger
CAM_RGain| Up| 8x 01 04 03 02 FF| Manual Control of R Gain
Down| 8x 01 04 03 03 FF|
CAM_Bgain| Up| 8x 01 04 04 02 FF| Manual Control of B Gain
Down| 8x 01 04 04 03 FF|
CAM_AE
| Full Auto| 8x 01 04 39 00 FF| Automatic Exposure mode
Manual| 8x 01 04 39 03 FF| Manual Control mode
Shutter Priority| 8x 01 04 39 0A FF| Shutter Priority Automatic Exposure mode
Iris Priority| 8x 01 04 39 0B FF| Iris Priority Automatic Exposure mode
CAM_SlowShutter| Auto| 8x 01 04 5A 02 FF| Auto Slow Shutter ON
Manual| 8x 01 04 5A 03 FF| Auto Slow Shutter OFF
CAM_Shutter| Down| 8x 01 04 0A 02 FF| Shutter Setting
Up| 8x 01 04 0A 03 FF|
CAM_Shutter| Reset| 8x 01 04 0A 00 FF|
CAM_Shutter| Direct| 8x 01 04 4A 00 00 0p 0q FF| pq: Shutter Position
CAM_Iris| Reset| 8x 01 04 0B 00 FF|
CAM_Iris| Up| 8x 01 04 0B 02 FF| Iris Setting
Down| 8x 01 04 0B 03 FF|
CAM_Iris| Direct| 8x 01 04 4B 00 00 0p 0q FF| pq: Iris Position，
CAM_Gain| Reset| 8x 01 04 0C 00 FF|
CAM_Gain| Up| 8x 01 04 0C 02 FF| Gain Setting
Down| 8x 01 04 0C 03 FF|
CAM_Gain| Direct| 8x 01 04 4C 00 00 0p 0q FF| pq: Gain Position，
CAM_Gain| AE Gain Limit (Direct)| 8x 01 04 2C 0p FF| p: Gain Position (4 to
F)，
CAM_ExpComp| Reset| 8x 01 04 0E 00 FF|
CAM_ExpComp| Up| 8x 01 04 0E 02 FF| Exposure Compensation Amount Setting
Down| 8x 01 04 0E 03 FF|
CAM_ExpComp| Direct| 8x 01 04 4E 00 00 0p 0q FF| pq: ExpComp (pq: 0x01~0x09 ,
Value: -4~ +4 , Each value = 0.3EV)
CAM_Backlight| On| 8x 01 04 33 02 FF| Back Light Compensation ON/OFF, only
supported in Auto Mode
Off| 8x 01 04 33 03 FF|
CAM_LR_Reverse| On| 8x 01 04 61 02 FF| Mirror Image ON/OFF
CAM_LR_Reverse| Off| 8x 01 04 61 03 FF
CAM_Memory
| Reset| 8x 01 04 3F 00 pp FF|
---|---|---|---
Set| 8x 01 04 3F 01 pp FF| pp: 0x00 To 0xFF
pp: 0x5A => SmartFrame Enable pp: 0x5B => SmartFrame Disable pp: 0x5C => SmartFrame Trigger pp: 0x5D => SmartShoot Enable pp: 0x5E => SmartShoot Disable pp: 0x5F => Trun on OSD menu
Recall| 8x 01 04 3F 02 pp FF|
SYS_Menu| On| 8x 01 06 06 02 FF| turn on the menu screen
SYS_Menu| Off| 8x 01 06 06 03 FF| Erasing menu display(turn off the menu
screen/VC-A70H)
CAM_Menu| On/Off| 8x 01 06 06 10 FF| Display ON/OFF
SYS_Menu| Menu Enter| 8x 01 7E 01 02 00 01 FF| menu enter
Pan-tilt Drive
| Up| 8x 01 06 01 VV WW 03 01 FF|
VV: Pan speed setting 0x01 (low speed) to 0x18 (high speed) WW: Tilt speed setting 0x01 (low speed) to 0x18 (high speed)
Down| 8x 01 06 01 VV WW 03 02 FF
Left| 8x 01 06 01 VV WW 01 03 FF
Right| 8x 01 06 01 VV WW 02 03 FF
UpLeft| 8x 01 06 01 VV WW 01 01 FF
UpRight| 8x 01 06 01 VV WW 02 01 FF
DownLeft| 8x 01 06 01 VV WW 01 02 FF
DownRight| 8x 01 06 01 VV WW 02 02 FF
Stop| 8x 01 06 01 VV WW 03 03 FF
Home| 8x 01 06 04 FF|
Reset| 8x 01 06 05 FF|
Absolute Position
| |
8x 01 06 02 VV WW 0Y 0Y 0Y 0Y 0Z 0Z
0Z 0Z FF
| VV: Pan speed setting 0x01 (low speed) to 0x18 (high speed)
WW: Tilt speed setting 0x01 (low speed) to 0x18 (high speed) YYYY: Pan Position 8A14 to 762C (CENTER 0000)
ZZZZ: Tilt Position 468B to E898 (Image Flip: OFF) (CENTER 0000)
Pan-tiltSet SlowPanTilt| On| 8x 01 06 44 02 FF| Pan/Tilt Slow Mode On/Off
Pan-tiltSet SlowPanTilt| Off| 8x 01 06 44 03 FF
Firmware| Firmware version| 8x 01 02 03 FF|
Factory Reset| System Factroy Reset| 8x 01 04 3F 03 00 FF|
Preset Speed| Set Preset Speed| 8x 01 06 20 0p FF| p:1 to 6
CAM_Power_ON| Power On| 8x 01 04 00 02 FF|
CAM_Power_OFF| Power Off| 8x 01 04 00 03 FF|
Inquiry Command| Command| Command Packet| Comments
---|---|---|---
PT_Pos_Inq| Inquiry| 8x 09 06 12 FF|
zoom_Pos_Inq| Zoom Position Inquiry| 8x 09 04 47 FF|
CAM_PowerInq| 8x 09 04 00 FF| y0 50 02 FF| On
y0 50 03 FF| Off (not for Hardware version C)
CAM_WBModeInq| 8x 09 04 35 FF| y0 50 00 FF| Auto
| | y0 50 05 FF| Manual
CAM_AEModeInq
|
8x 09 04 39 FF
| y0 50 00 FF| Full Auto
y0 50 03 FF| Manual
y0 50 0A FF| Shutter Priority
y0 50 0B FF| Iris Priority
CAM_AutoFocusInq| 8x 09 04 38 FF| y0 50 02 FF| On
y0 50 03 FF| Off
Visca-over-IP Settings
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>