eurolite TSL-350 LED Scan COB User Manual

June 9, 2024
eurolite

eurolite TSL-350 LED Scan COB

eurolite-TSL-350-LED-Scan-COB-PRODUCT-IMG

Product Information

The LED TSL-350 Scan COB is a handy scanner that features a 60W COB LED and a gobo and color wheel. It can be controlled through DMX, stand-alone, or master/slave modes. The scanner also has a cold white LED and manual focus (optional). The product comes with a safety eyelet, DMX in/out connections, and a USB port. The product is manufactured by Eurolite and has a model number of 51786150 or 51786151.

Product Usage Instructions

  1. Installation: Before installation, make sure to disconnect the power source. Insert or exchange gobos as needed. Connect the scanner to the power source through a switchable socket.
  2. DMX Control: Connect the scanner to a DMX controller using the DMX in/out connections. Set the DMX start address as needed.
  3. Master/Slave Mode: Connect multiple scanners together in master/slave mode.
  4. Control Board: The control board features several buttons for different functions. Use the Mode button to select different modes, such as show mode or sound mode. Use the Up/Down buttons to adjust settings, such as music sensitivity or LCD light. Use the Enter button to confirm selections.

DANGER! Electric shock caused by short-circuit Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric shock when touching the wires. Never open the housing. Keep the device away from rain and moisture.
Please read these instructions carefully before using the product. They contain important information for the correct use of the product.

Every person involved with the installation, operation and maintenance of this device has to

  • be qualified
  • follow the instructions of this manual
  • consider this manual to be part of the total product
  • keep this manual for the entire service life of the product
  • pass this manual on to every further owner or user of the product
  • download the latest version of the user manual from the Internet

INTRODUCTION

Thank you for having chosen one of our products. If you follow the instructions given in this manual, we are sure that you will enjoy this device for a long period of time.

Product features

Handy scanner with 60 W COB LED, gobo and color wheel

  • Compact design
  • Built-in programs
  • Strobe effect with 2-18 flashes per second
  • Electronic dimmer (0-100%)
  • Available in black or white
  • 1 powerful LED 60 W COB (chip-on-board) cold white (CW)
  • Color wheel 7 dichroic filters plus open
  • Rainbow effect with adjustable speed
  • Gobo wheel with rotating gobos, 7 gobos and open
  • Gobos changeable
  • Slot-in gobo system for exchanging gobos without tools
  • Shake effect
  • Can be operated in 10 CH mode
  • The device is cooled by cooling fan
  • Controlling by stand-alone; DMX; QuickDMX via USB (optional); Master/slave function; Sound to light via Microphone; W-DMX by wireless solution; CRMX by LumenRadio
  • Flicker-free projection
  • With a beam angle of 11°
  • LCD display for easy controlling
  • With 4 rubber feet

SAFETY INSTRUCTIONS

WARNING!
Please read the safety warnings carefully and only use the product as described in this manual to avoid accidental injury or damage.

Intended use

  • This device is an LED lighting effect device for creating decorative effects. This device is designed for professional use in the field of event technology, e.g. on stage. It is not suitable for household lighting.
  • Only use the device according to the instructions given herein. Damages due to failure to follow these operating instructions will void the warranty! We do not assume any liability for any resulting damage.
  • We do not assume any liability for material and personal damage caused by improper use or noncompliance with the safety instructions. In such cases, the warranty will be null and void.
  • Unauthorized rebuilds or modifications of the device are not permitted for reasons of safety and render the warranty invalid.

Danger due to electricity

  • The device is suitable for indoor use only. Do not use it outdoors. Never expose it to rain or moisture. Do not store it in rooms exposed to moisture.
  • To reduce the risk of electric shock, do not open any part of the device. There are no serviceable parts inside the device.
  • Only connect the device to a properly installed mains outlet. The outlet must be protected by residual current breaker (RCD). The voltage and frequency must exactly be the same as stated on the device. If the mains cable is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a mains cable. Failure to do so could possibly injure the user.
  • The mains outlet must be easily accessible so that you can unplug the device quickly if need be.
  • Never touch the mains plug with wet or damp hands. There is the risk of potentially fatal electric shock.
  • The mains cable must not be bent or squeezed. Keep it away from hot surfaces or sharp edges.
  • Never pull the mains cable to disconnect the mains plug from the mains outlet, always seize the plug.
  • Unplug the device during lightning storms, when unused for long periods of time or before cleaning.
  • Do not expose the device to any high temperatures, direct sunlight, dripping or splashing water, strong vibrations or heavy mechanical stress.
  • Do not place any objects filled with liquids on the device.
  • Do not place any open sources of fire, such as burning candles, on or directly next to the device.
  • Make sure that objects cannot fall into the device, in particular metal parts.
  • Only have repairs to the device or its mains cable carried out by qualified service personnel. Repairs are required when the device or the mains cable is visibly damaged, liquid has been spilled or objects have fallen into the device; when the device has been exposed to rain or moisture, has been dropped or malfunctions occur.
  • Cleaning of the device is limited to the surface. Make sure that moisture does not come into contact with any areas of the terminal connections or mains voltage control parts. Only wipe off the product with a soft lint-free and moistened cloth. Never use solvents or aggressive detergents.

Danger to children and people with restricted abilities

  • This product is not a toy. Keep it out of the reach of children and pets. Do not leave packaging material lying around carelessly. Never leave this device running unattended.
  • This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety.

Warning – risk of burns and fire

  • The admissible ambient temperature range (Ta) is -5 to +45°C. Do not operate the device outside of this temperature range.
  • The housing temperature (Tc) can be up to 55°C during use. Avoid contact by persons and materials.
  • Do not illuminate surfaces within 10 cm of the device. This value is indicated on the device by the symbol.
  • Do not use the device near highly flammable materials. Always place the device at a location where sufficient air circulation is ensured. Leave 50 cm of free space around the device. Never cover the air vents of the housing.

Warning – risk of injuries

  • Do not look directly at the light source. Persons with light-sensitive epilepsy may suffer from epileptic seizures or fall unconscious.
  • Make sure that the product is set up or installed safely and expertly and prevented from falling down. Comply with the standards and rules that apply in your country, in particular EN 60598-2-17.
  • If you lack the qualification, do not attempt the installation yourself, but instead use a professional installer. Improper installation can result in bodily injury and or damage to property.
  • The manufacturer cannot be made liable for damages caused by incorrect installations or insufficient safety precautions.
  • For overhead use, always secure the device with a secondary safety attachment such as a safety bond or safety net.
  • Make sure that the area below the installation place is blocked when rigging, derigging or servicing the device.
  • For commercial use the country-specific accident prevention regulations of the government safety organization for electrical facilities must be complied with at all times.

Caution – material damage

  • This device must not be connected to the mains voltage by means of a dimmer.
  • Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects.
  • Never switch the device on and off in short intervals. This will considerably reduce the service life of the device.
  • If the device has been exposed to drastic temperature fluctuation, do not switch it on immediately. The resulting condensation may destroy the device. Allow the device to reach room temperature before connecting it. Wait until the condensation has evaporated.
  • Please use the original packaging to protect the device against vibration, dust and moisture during transportation or storage.
  • If a serial number label is affixed to the device, do not remove the label as this would make the warranty void.

DESCRIPTION OF THE DEVICE

  1. Fixation screw
  2. Mounting bracket
  3. Mirror
  4. Objective-lens
  5. Housing
  6. Control boardeurolite-TSL-350-LED-Scan-COB-FIG-1
  7. Safety eyelet
  8. Fuseholder
  9. Power supply
  10. USB port for QuickDMX receiver
  11. Microphone
  12. DMX-In
  13. DMX-Out
  14. Display
  15. Mode button
  16. Up button
  17. Down button
  18. Enter button

INSTALLATION

WARNING! Risk of injury caused by falling objects Devices in overhead installations may cause severe injuries when crashing down. Make sure that the device is installed securely and cannot fall down. The installation must be carried out by a specialist who is familiar with the hazards and the relevant regulations.

eurolite-TSL-350-LED-Scan-COB-FIG-4

The device may be placed on the floor or fastened to a truss or similar rigging structure. The device must never be fixed swinging freely in the room.

  1. The rigging structure must support at least 10 times the weight of all fixtures to be installed on it.
  2. Block access below the work area and work from a stable platform when installing the device.
  3. Use rigging hardware that is compatible with the structure and capable of bearing the weight of the device. Please refer to the “Accessories” section for a list of suitable rigging hardware.
  4. Secure the device with a safety bond or other secondary attachment. This secondary safety attachment must be sufficiently dimensioned in accordance with the latest industrial safety regulations and constructed in a way that no part of the installation can fall down if the main attachment fails. An appropriate eyelet is mounted on the device for fixation of the safety bond. Fasten the safety bond in such a way that, in the event of a fall, the maximum drop distance of the device will not exceed 20 cm.
  5. To align the device, release the fixation screws at the mounting bracket, adjust the desired inclination angle and tighten the fixation screws.
  6. After installation, the device requires inspections periodically to prevent the possibility of corrosion, deformation and looseness.

Inserting/Exchanging gobos

DANGER!
Install the gobos with the device switched off only. Unplug from mains before!

If you wish to use other forms and patterns as the standard gobos, or if gobos are to be exchanged, please follow the instructions below:

CAUTION!
Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be opened!

Remove the fixation ring with an appropriate tool. Remove the gobo and insert the new gobo. Press the fixation ring together and insert it in front of the gobo.

eurolite-TSL-350-LED-Scan-COB-FIG-5

Notes!
Slot-in gobo-system for exchanging gobos without tools! Inserting/Exchanging gobos as described above.

CONNECTIONS

DMX512 control

eurolite-TSL-350-LED-Scan-COB-FIG-6

A DMX512 data link is required in order to control the device via DMX. The device provides 3-pin XLR connectors for DMX connection.

  1. Connect the output of your DMX controller to the DMX input DMX IN of the device with a DMX cable.
  2. Connect the DMX output DMX OUT of the device to the DMX input of the next unit in the chain. Always connect one output to the input of the next unit until all units are connected.
  3. At the last unit, the DMX cable has to be terminated. Plug the terminator with a 120 Ω resistor between Signal (–) and Signal (+) in the DMX output of the last unit.
  4. If the cable length exceeds 300 m or the number of DMX devices is greater than 32, it is recommended to insert a DMX-level amplifier to ensure proper data transmission.

XLR connection

eurolite-TSL-350-LED-Scan-COB-FIG-7

Wireless DMX transmission with QuickDMX
The device features an alternative DMX input for a QuickDMX receiver (sold separately). CRMX and WDMX receivers are compatible and can also be used. The connector allows a DMX control signal to be transmitted wirelessly to the device, eliminating the need for complex wiring to the DMX controller. The connector is designed as a USB port which provides the required 5 V operating voltage for the receiver. Occupation of the USB port:

Connection to the mains
The device uses an auto-range power supply that accepts input voltages between 100 und 240 volts.

  1. Connect the device via the enclosed mains cable to a grounded mains socket. Thus the unit is switched on.
  2. To switch off the unit, disconnect the power plug.
  3. Do not connect the unit to the mains voltage via a dimmer. For a more convenient operation, use a mains outlet which is switchable.

Master/Slave operation
The master/slave operation enables several devices can be synchronized and controlled by one master device. On the rear panel of the device you can find an XLR-jack (DMX Out) and an XLR-plug (DMX In), which can be used for connecting several devices. Choose the device which is to control the effects. This device then works as master device and controls all other slave-devices, which are to be connected to the master device via a DMX cable. Connect the DMX OUT-jack with the DMX IN-plug of the next device. Set “Mast“ for the master device, as described in chapter Control Board. Set “Slv1” or “Slve2” for all slave devices.

OPERATION

Completely remove the transport safeties (cable ties) at the mirror. (Only necessary at initial start-up!) After connecting the device to the mains it is ready for operation. The display indicates the last operating mode. The operating modes can be selected by means of the display and the control buttons. All settings remain stored even if the device is disconnected from the mains. The device can be operated in stand-alone mode via the control board or in DMX-controlled mode via any commercial DMX controller as well as wireless via QuickDMX with the optionally available EUROLITE QuickDMX USB Wireless Transmitter/Receiver. After you connected the effect to the mains, the EUROLITE LED TSL-350 Scan COB starts running. During the Reset, the motors are trimmed and the device is ready for use afterwards.

Control Board
The Control Board offers several features: you can e. g. easily set the starting address. The main menu is accessed by pressing the Mode button. Browse through the menu by pressing the Mode button. Press the Enter button in order to select the desired menu. You can change the selection by pressing Up or Down. Confirm every selection by pressing the Enter button. You can leave every mode by pressing the Mode button. The functions provided are described in the following sections.

eurolite-TSL-350-LED-Scan-COB-FIG-9

DMX operation
Setting the DMX starting address For operation with a controller with DMX512 protocol, the device is equipped with 10 control channels. To be able to operate the device with a DMX controller, the DMX starting address must be set. The starting address depends upon which DMX controller is being used. Please refer to the controller’s documentation.

  1. Press the UP or DOWN button so many times until DMX Set Address is indicated on the display. Confirm with the ENTER button.
  2. Now the display calls up the menu item for the DMX starting address: A001.
  3. Use the buttons UP and DOWN to set the address. Confirm with the ENTER button.
  4. The display will flash when DMX signals are being received.

Note: Please make sure that you do not have any overlapping channels in order to control each device correctly and independently from any other fixture on the DMX chain. If several devices are addressed to the same address, they will work synchronously.

Functions in DMX mode

eurolite-TSL-350-LED-Scan-COB-FIG-10 eurolite-
TSL-350-LED-Scan-COB-FIG-11eurolite-TSL-350-LED-Scan-COB-
FIG-12eurolite-TSL-350-LED-Scan-COB-
FIG-13eurolite-TSL-350-LED-Scan-COB-
FIG-14

eurolite-TSL-350-LED-Scan-COB-FIG-15

CLEANING AND MAINTENANCE

The outside of the device should be cleaned periodically to remove contaminants such as dust etc. The lens, in particular, should be clean to ensure that light will be emitted at maximum brightness.

  1. Disconnect the device from power and allow it to cool before cleaning.
  2. Clean the surface with a soft lint-free and moistened cloth. Never use alcohol or solvents as these may damage the surface. Make sure that no liquids can enter the device.
  3. The device must be dry before reapplying power.

There are no serviceable parts inside. Do not open the housing. Do not try to repair the device by yourself as this may result in damage. Maintenance and service operations are only to be carried out by authorized dealers. Should you need any spare parts, please use genuine parts. Should you have further questions, please contact your dealer.

Replacing the fuse
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.

  1. Disconnect the device from power and allow it to cool.
  2. Open the fuse holder of the mains connection with a fitting screwdriver.
  3. Remove the old fuse from the fuse holder and replace it with a new fuse.
  4. Carefully push the fuse holder back into its position before reapplying power.

PROTECTING THE ENVIRONMENT

Disposal of old equipment
When to be definitively put out of operation, take the product to a local recycling plant for a disposal which is not harmful to the environment. Devices marked with this symbol must not be disposed of as household waste. Contact your retailer or local authorities for more information. Remove any inserted batteries and dispose of them separately from the product. You as the end user are required by law (Battery Ordinance) to return all used batteries/ rechargeable batteries. Disposing of them in household waste is prohibited. You may return your used batteries free of charge to collection points in your municipality and anywhere where batteries/rechargeable batteries are sold. By disposing of used devices and batteries correctly, you contribute to the protection of the environment.

TECHNICAL SPECIFICATIONS

eurolite-TSL-350-LED-Scan-COB-FIG-16 eurolite-
TSL-350-LED-Scan-COB-FIG-17

Accessories

eurolite-TSL-350-LED-Scan-COB-FIG-18

All information is subject to change without prior notice. © 04.08.2022 Eurolite is a brand of Steinigke Showtechnic GmbH Andreas-Bauer-Str. 5 97297 Waldbüttelbrunn Germany 00141500 Version 1.0 Publ. 04/08/2022

Handlicher Scanner mit 60-W-COB-LED, Gobo- und Farbrad Handy scanner with 60 W LED, gobo and color wheel

  • No. 51786150
  • No. 51786151

www.eurolite.de

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals