HYTRONIK HIR32 Series PIR Standalone Motion Sensor Installation Guide

June 9, 2024
HYTRONIK

HBIR32 HBIR32/R HBIR32/W
HBIR32/H HBIR32/RH
Installation and Instruction Manual

PIR Standalone Motion Sensor with 5.0 SIG Mesh Two DALI Channels Output

Technical Specifications

Operation frequency 2.4 GHz – 2.483 GHz
Transmission power 4 dBm
Range (Typical indoor) 10~30m
Protocol 5.0 SIG Mesh
Operating voltage 220~240VAC 50/60Hz
Stand-by power <1W
DALI Channel 1 50mA, Max. 25 LED drivers
DALI Channel 2 30mA, Max. 15 LED drivers
Sensor principle PIR detection

Detection range (Max.)
HBIR32| Installation Height : 6m
Detection Range (Ø) :9m
Detection range (Max.)

HBIR32/R| Installation Height : 6m
Detection Range(Ø) :10m
Detection range (Max.) HBIR32/W| Installation Height : 6m Detection Range(Ø) :18m
Detection range (Max.)
HBIR32/H| Installation height:15m (forklift)
12m (person) Detection range (Ø):24m
Detection range (Max.)* HBIR32/RH| Installation height:20m (forklift)
12m (person) Detection range (Ø):40m
Detection angle| 360O
Operation temperature| Ta:-20OC~+50OC
IP rating| IP20
EMC standard (EMC)| EN55015, EN61000, EN61547
Safety standard (LVD)| EN60669-1/-2-1
AS/NZS60669-1/-2-1
RED| EN300328, EN301489-1/-17
Certification| CB, CE , EMC, RED, RCM

Download the App

Free App for set-up and commissioning

https://apps.apple.com/cn/app/koolmesh/id1483721878| https://play.google.com/store/apps/details?id=com.koolmesh.sig
---|---

Smartphone app for both iOS & Android platformhttps://apps.apple.com/cn/app/koolmesh/id1570378349

Web app/platform: www.iot.koolmesh.com

Installation

Mechanical Structure & DimensionsHYTRONIK HIR32 Series PIR Standalone Motion
Sensor

  1. Ceiling (drill hole φ66~68mm)
  2. Carefully prise off the cable clamps.
  3. Make connections to the pluggable terminal blocks.
  4. Insert plug connectors and secure using the provided cable clamps, then clip terminal covers to the base.
  5. Fit detection blind (if required) and desired lens.
  6. Clip fascia to body.
  7. Bend back springs and insert into ceiling.

HYTRONIK HIR32 Series PIR Standalone Motion Sensor - fig
4 Wire PreparationHYTRONIK HIR32
Series PIR Standalone Motion Sensor - fig 5 Pluggable screw terminal. It is recommended to make connections to the terminal before fitting to the sensor.

  1. 200 metres (total) max. for 1mm² CSA (Ta = 50 ℃)
  2. 300 metres (total) max. for 1.5mm² CSA (Ta = 50 ℃)

Wiring DiagramHYTRONIK HIR32 Series PIR Standalone Motion Sensor - fig
6

Dimming Interface Operation Notes

Switch-Dim
The provided Switch-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switches. Detailed Push switch configurations can be set on Koolmesh app.

Switch Function Action Descriptions
Push switch Short press (<1 second)
* Short press has to be longer than 0.1s, or it will be invalid. – Turn on/off

– Recall a scene
– Turn on only
– Exit manual mode
– Turn off only
– Do nothing
Double push| – Turn on only
– Exit manual mode
– Turn off only
– Do nothing
– Recall a scene
Long press (≥1 second)| – Dimming
– Colour tuning
– Do nothing
Simulate sensor| /| – Upgrade a normal on/off motion sensor to a Bluetooth controlled motion sensor

Detection Pattern & Optional Accessories

1. HBIR32 (Low-bay)
HBIR32: Low-bay flat lens detection pattern for single person @ Ta = 20ºC (Recommended ceiling mount installation height 2.5m-6m)

Mount height Tangential (A) Radial (B)
2.5m max 50m2 (0= 8m) max 13m’ (0= 4m)
3m max 64m2 (0= 8m) max 13m2 (0= 4m)
4m max 38m2 (0= 8m) max 13m’ (0= 4m)
5m max 38m2 (0= 8m) max 13m2 (0= 4m)
6m max 38m2 (0= 8m) max 13m’ (0= 4m)

Optional Accessory — Ceiling/Surface Mount Box: HA03HYTRONIK HIR32
Series PIR Standalone Motion Sensor - fig 9 Optional Accessory — Blind Insert for Blocking Certain Detection AnglesHYTRONIK HIR32 Series PIR Standalone Motion Sensor - fig
10 2. HBIR32/R (Reinforced Low-bay)
HBIR32: Low-bay flat lens detection pattern for single person @ Ta = 20ºC (Recommended ceiling mount installation height 2.5m-6m)

Mount height Tangential (A) Radial (B)
2.5m max 79m2 (Ø = 10m) max 20m2 (Ø = 5m)
3m max 79m2 (Ø = 10m) max 20m2 (Ø = 5m)
4m max 64m2 (Ø = 9m) max 20m2 (Ø = 5m)
5m max 50m2 (Ø = 8m) max 20m2 (Ø = 5m)
6m max 50m2 (Ø = 8m) max 20m2 (Ø = 5m)

Optional Accessory — Ceiling/Surface Mount Box: HA03HYTRONIK HIR32
Series PIR Standalone Motion Sensor - fig 12 Optional Accessory — Blind Insert for Blocking Certain Detection AnglesHYTRONIK HIR32 Series PIR Standalone Motion Sensor - fig
13 3. HBHC25/W (Wide range Low-bay)
HBIR32: Low-bay flat lens detection pattern for single person @ Ta = 20ºC (Recommended ceiling mount installation height 2.5m-6m)

Mount height Tangential (A) Radial (B)
2.5m max 254m² (Ø = 18m) max 28m² (Ø = 6m)
3m max 254m² (Ø = 18m) max 28m² (Ø = 6m)
4m max 154m² (Ø = 14m) max 28m² (Ø = 6m)
5m max 113m² (Ø = 12m) max 28m² (Ø = 6m)
6m max 79m² (Ø = 10m) max 13m² (Ø = 4m)

Ceiling/Surface Mount Accessory HA03: Default IP20, IP65 can be request with extra big & small water-proof gasketsHYTRONIK HIR32 Series PIR
Standalone Motion Sensor - fig 15 Big and small silicon gasket used to make IP54 degree protection when HBIR32 series device mounted into HA03 housing for ceiling mountHYTRONIK HIR32 Series PIR Standalone Motion Sensor - fig
16 Placement Guide and Typical Range The smart device with the App installed will have a typical range of 10m, but varies from device to device. During commissioning, the installer will need to be in range of the devices when searching for devices to add to the network.
Once the devices have been added to the network via the App, the devices will start communicating within the wireless mesh. This means that once the network is complete, all devices are accessible from the smart device when in a 20m range of a single point.
4. HBIR32/H (High-bay)
HBIR32/R: High-bay lens detection pattern for forklift @ Ta = 20ºC (Recommended ceiling mount installation height 10m-15m)

Mount height Tangential (A) Radial (B)
10m max 380m2 (Ø = 22m) max 201m2 (Ø = 16m)
11m max 452m2 (Ø = 24m) max 201m2 (Ø = 16m)
12m max 452m2 (Ø = 24m) max 201m2 (Ø = 16m)
13m max 452m2 (Ø = 24m) max 177m2 (Ø = 15m)
14m max 452m2 (Ø = 24m) max 133m2 (Ø = 13m)
15m max 452m2 (Ø = 24m) max 113m2 (Ø = 12m)

HBIR32/H: High-bay lens detection pattern for single person @ Ta = 20ºC (Recommended ceiling mount installation height 2.5m-12m)

Mount height Tangential (A) Radial (B)
2.5m max 50m2 (Ø = 8m) max 7m2 (Ø = 3m)
6m max 104m2 (Ø = 11.5m) max 7m2 (Ø = 3m)
8m max 154m2 (Ø = 14m) max 7m2 (Ø = 3m)
10m max 227m2 (Ø = 17m) max 7m2 (Ø = 3m)
11m max 269m2 (Ø = 18.5m) max 7m² (Ø = 3m)
12m max 314m2 (Ø = 20m) max 7m² (Ø = 3m)

Optional Accessory — Ceiling/Surface Mount Box: HA03HYTRONIK HIR32
Series PIR Standalone Motion Sensor - fig 20 Optional Accessory — Blind Insert for Blocking Certain Detection AnglesHYTRONIK HIR32 Series PIR Standalone Motion Sensor - fig
21 5. HBIR32/RH (Reinforced High-bay with 3-Pyro)
HBIR32/RH: Reinforced high-bay lens detection pattern for forklift @ Ta = 20ºC (Recommended ceiling mount installation height 10m-15m)

Mount height Tangential (A) Radial (B)
10m max 346m2 (Ø = 21m) max 177m2 (Ø = 15m)
11m max 660m2 (Ø = 29m) max 177m2 (Ø = 15m)
12m max 907m2 (Ø = 34m) max 154m2 (Ø = 14m)
13m max 962m2 (Ø = 35m) max 154m2 (Ø = 14m)
14m max 1075m2 (Ø = 37m) max 113m2 (Ø = 12m)
15m max 1256m2 (Ø = 40m) max 113m2 (Ø = 12m)
20m max 707m2 (Ø = 30m) max 113m2 (Ø = 12m)

HBIR32/RH: Reinforced high-bay lens detection pattern for single person @ Ta = 20OC (Recommended ceiling mount installation height 2.5m-12m)

Mount height Tangential (A) Radial (B)
2.5m max 38m2 (Ø = 7m) max 7m2 (Ø = 3m)
6m max 154m2 (Ø = 14m) max 7m2 (Ø = 3m)
8m max 314m2 (Ø = 20m) max 7m2 (Ø = 3m)
10m max 531m2 (Ø = 26m) max 13m2 (Ø = 4m)
11m max 615m2 (Ø = 28m) max 13m2 (Ø = 4m)
12m max 707m2 (Ø = 30m) max 13m2 (Ø = 4m)

HYTRONIK HIR32 Series PIR Standalone Motion Sensor - fig
24

Additional Information / Documents

  1. To learn more about detailed product features/functions, please refer to www.hytronik.com/download ->knowledge ->Introduction of App Scenes and Product Functions
  2. Regarding precautions for Bluetooth product installation and operation, please kindly refer to www.hytronik.com ->download/knowledge ->Bluetooth Products – Precautions for Product Installation and Operation
  3. Data sheet is subject to change without notice. Please always refer to the most recent release on www.hytronik.com/products/bluetooth technology ->Bluetooth Sensors
  4. Regarding Hytronik standard guarantee policy, please refer to www.hytronik.com/download ->knowledge ->Hytronik Standard Guarantee Policy

WWW.HYTRONIK.COM
Subject to change without notice.
HBIR32-20210813-A0

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

HYTRONIK User Manuals

Related Manuals