snom D713 VoIP Phone Installation Guide

: June 9, 2024
: snom

Table of Contents

Delivery content
Attaching the Footstone
Connecting
- Copyright, trademarks, legal disclaimers
Important information
Safety instructions
Standards conformance
Important additional information for the USA FCC part 15
- Consumer information
Important additional information Industry Canada
Technical specifications
Customer Support
Documents / Resources

snom D713 VoIP Phone

D713 VoIP Phone

Delivery content

Attaching the Footstone

Connecting

**C**
Connecting

If no PoE available
Not included in delivery
Optional

Copyright, trademarks, legal disclaimers

© 2021 Snom Technology GmbH. All Rights Reserved.
Snom, the names of Snom products, and Snom logos are trademarks owned by Snom Technology GmbH. Snom, the names of Snom products, and Snom logos are trademarks owned by Snom Technology GmbH.
All product specifications are subject to change without notification. Snom Technology GmbH reserves the right to revise and change this document at any time, without being obliged to announce such revisions or changes beforehand or after the fact.
Although due care has been taken in the compilation and presentation of the information in this document, the data upon which it is based may have changed in the meantime. Snom therefore disclaims all warranties and liability for the accurateness, completeness, and currentness of the information published, except in the case of intention or gross negligence on the part of Snom or where liability arises due to binding legal provisions.

Important information

Please read the instructions on safety and disposal and on how to set up and use the device before using it and also give them to other users to read or inform those users of their contents.
The nameplate is located at the bottom or rear of the product.

Safety instructions

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Warning: The product included (ITE) in this manual is to be connected only to PoE networks without routing to the outside plant.
The socket outlet for the power adaptor must be near the equipment and easily accessible.
Mount the device only at heights not exceeding 2m.
Follow the instructions in this manual and other applicable documentation of the device.
If the phone is not supplied with power via the Ethernet cable, use only a power adapter expressly recommended by Snom Technology. Other power supplies may damage or destroy the phone, affect its behavior, or induce noise.
Avoid placing the cables where people may trip over them or where they may be exposed to mechanical pressure as this may damage them.
This device is for indoor use only! NOT FOR OUTDOOR USE!
Do not install the device in rooms with high humidity (for example, in bathrooms, laundry rooms, damp basements). Do not immerse the device in water and do not spill or pour liquids of any kind onto or into the device.
Do not install the device in surroundings at risk for explosions (paint shops, for example). Do not use the device if you smell gas or other potentially explosive fumes.
Do not use the device during thunderstorms.
Lightning striking the power grid may cause electric shocks.
Warning: The handset contains a magnet, and its earpiece may attract small dangerous objects such as needles or pins. Please ensure before each use that no such objects are present.
Safety status of input/output connections comply with SELV (Safety Extra Low Voltage) requirements.
Warning: To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV, PSTN ports TNV circuits. Some LAN and PSTN ports both use RJ-45 connectors. Use caution when connecting cables.

Standards conformance

This device complies with the essential health, safety, and environmental requirements of all relevant European directives and UK legislation. The declaration of conformity can be downloaded at https://www.snom.com/conformity.

This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. This phone is FCC Class A verified and meets US health, safety, and environmental standards.

Unauthorized opening, changing, or modifying the device will cause the warranty to lapse and may result in the loss of CE and ISED conformity and the FCC verification. In case of malfunction contact authorized service personnel, your seller, or Snom.

Important additional information for the USA FCC part 15

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user’s expense.

WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Consumer information

a. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
b. An applicable certification jacks Universal Service Order Codes (USOC) for the equipment is provided (i.e., RJ45C) in the packaging with each piece of approved terminal equipment.
c. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant LAN cable (RJ45) and modular plug is provided with this product. An RJ45 jack should normally be used for connecting to the SIP equipment through the LAN cable. See installation instructions for details.
d. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn‘t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
e. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
f. Should you experience trouble with this equipment, please contact Snom Technology GmbH 1 339-227-6160 (select option 2) for repair or warranty information. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
g. Please follow instructions for repairing if any (e.g. battery replacement section); otherwise do not alternate or repair any parts of device except specified.
h. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.
i. NOTICE: If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this D713 does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
j. This equipment is hearing aid compatible.

NOTICE: According to telephone company reports, AC electrical surges, typically resulting from lightning strikes, are very destructive to telephone equipment connected to AC power sources. To minimize damage from these types of surges, a surge arrestor is recommended.

Important additional information Industry Canada

This Class A digital apparatus complies with Canadian requirements: CAN ICES-3 (A)/NMB-3(A).

This product meets the applicable Innovation, Science and Econonmic Development Canada technical specifications.

Technical specifications

Safety: IEC 62368-1
Connectors:
◦ 2 x RJ45 (Ethernet): 1x LAN, 1x PC
◦ 2 x 4P4C (handset, optional headset)
◦ 1 x RJ12
Ethernet: 2 x IEEE 802.3 / 1 Gigabit Ethernet switch
Power over Ethernet (PoE): IEEE 802.3af, Class 2 If PoE is not available, use one of the separately available power adapter (not included in delivery):

◦ Mass Power, model NBS12E050200UV, Snom PN 00004570
◦ Rongweixin, model R122-0502000ID, Snom PN 00004571

Disposal

This device is subject to European Directive= 2012/19/EU and may not be disposed of with general household garbage. If you do not know where to dispose of the device at the end of its life-span, contact your municipality, local waste management provider, or vendor.

In countries outside the European Union disposal should be done in line with local regulations. Please contact local authorities for further information.

Cleaning

To clean the device, use an anti-static cloth. Please avoid cleaning liquids as they might damage the surface or internal electronics of the device.
Setting up and connecting the phone: See figures B and C.

Initializing and registering the phone

NOTE: You will need the registration information received from your Internet service provider or your network administrator – normally the phone or extension number, the password, and the registrar.

After you have set up the phone and connected it to the network, it will begin to initialize. Normally the initialization is completely automatic, using DHCP.

If your network does not support DHCP, you must obtain the IP address, netmask, IP gateway, and DNS server from your Internet service provider or your network administrator and enter them manually when you are asked to do so on the display.

Watch the display and, when prompted, select an option by pressing the up or down arrow on the navigation key (Fig. D). Save your selection by pressing the OK key .

Language. The default is English.
Time zone. Press the function key underneath / to go to the next/previous time zone, then to show all available options within that time zone.
Tone scheme (dial tone)
The display shows the “Welcome” screen. Press any key to log on.
NOTE: To view the phone’s IP address at this stage, press .
Enter the account number. Press to save.
Enter the registrar. Press to save.
Reboot the phone.
Enter the password received from your Internet service provider or administrator. Press to save. After successful registration you will see the idle screen.

For further information, please refer our web page https://service.snom.com.

Customer Support

Snom Technology GmbH
Wittestr. 30 G
13509 Berlin, Deutschland
office.de@snom.com
VTech Communications Inc.
Snom Americas
9020 Washington Square Road, Suite 555
Tigard, OR 97223
Phone support: (339) 227 6160
VTech Technologies Canada Ltd.
Suite 222
13888 Wireless Way
Richmond, B.C. V6V 0A3, Canada
Phone support: (339) 227 6160
Snom Technology GmbH
Via Milano 1
20020 Lainate, Italia
office.it@snom.com
Snom Technology GmbH
The Courtyard
High Street
Ascot, Berkshire SL5 7HP, UK
office.uk@snom.com
SnomTechnology GmbH
130, avenue Joseph Kessel
78960 Voisins-le- Bretonneux,Franceoffice.fr@snom.com
Manufacturer:
VTech Telecommunications Ltd.
23/F., Tai Ping Industrial Centre, Block 1,
57 Ting Kok Road, Tai Po
HONG KONG