VEVOR K3001 Knob Induction Cooker Instruction Manual

VEVOR K3001 Knob Induction Cooker

The Knob Induction Cooker K3001 is an electric stove that uses induction technology to heat the cooking vessel. It has a glass plate on top and a control panel on the side, where you can adjust the temperature and other settings. The product voltage is 120V, and it has a rated power of 1300 watts and 1000 watts.

Control Panel

The control panel has four buttons: ON/OFF, UP, DOWN, and TIMER LOCK. There are two independent furnace areas, and each has its own power button. The standby state displays 0 for both areas. You can adjust the temperature by pushing the regulator in the standby state. There are ten heating gears, and the P gear is for rapid heating. The corresponding temperature of each section of fire ranges from 1 to 9 and P.

Usable Pans

The Knob Induction Cooker K3001 is compatible with all flat-bottom pots, but it works best with iron pots or magnetic pots. The weight limit for the food is 4kg.

Installation

If you plan to use the Knob Induction Cooker K3001 on a table, make sure to use high-temperature resistant, flame-retardant material for the table, such as marble.

Usage Instructions

1. Power on: Open the power supply knife of the machine cable. After power on, all display units will light up once, and the buzzer will drop once.
2. Power button: Press the power button for the desired furnace area to turn on the power and enter the standby state. The standby state displays 0.
3. Heating: Push the regulator in the standby state to enter the heating mode. The digital display 0 will turn into a number, indicating the temperature level. There are ten heating gears, and the P gear is for rapid heating. After three minutes, it will return to the 9 gear. Turn the regulator to 0 to stop heating.
4. Shutdown: In heating mode, long press the power button to return to the shutdown state.
5. Child lock: Press and hold the child lock button for 2-3 seconds to lock or unlock the child lock with a beep. After the lock is successful, the child lock number will display Lo, and the child lock can be operated in the power-off or standby heating state. Do not operate any steps except the child lock.
6. Panel high-temperature warning: After use, there is still residual temperature on the furnace panel. The warning display H will be shown. Be careful of scalding hands.

Trouble Code And Troubleshooting

If you encounter any issues with the Knob Induction Cooker K3001, refer to these trouble codes and their corresponding troubleshooting steps:

• E0: No pot detected.
• E1: The voltage is lower than 60.
• E2: Excessive voltage (voltage higher than 138).
• E3: Circuit error.
• E4, E5, E6: The IGBT sensor is open.
• E8: The control board is not connected to the main power supply board.

The information in this handbook is correct at the time of printing. Our company is responsible for revising and updating this handbook. and handbook without notice this handbook contains sketches which are to be used as a reference only. Please use common sense if these sketches are not exactly your situation or products.

Control Panel

The above is only the schematic diagram of the structure, please refer to the actual object.

Schematic Diagram Of The Control Panel

Instruction

Product voltage :120V Rated power:1300 watts and 1000watts

1. Power on: open the power supply knife of the machine cable. After powering on, all display units will light up once and the buzzer will drop once.

2. Power button: each furnace area has an independent power button. When you was one of the burners, press the power button to turn on the power and enter the standby state.

3. Standby state: Press the power button as described in the second operation and enter the standby mode, which displays 0 (0 is not heated). The standby mode automatically exits and returns to the shutdown state without any operation for a long time.
   The standby state is shown as follows: 0 is the standby state in both furnace areas.

4. Heating: for example, if you want to use the furnace area for heating, push the regulator in the standby state. When the digital display 0 turns into a number, the furnace area enters the heating mode. As shown in Figure 9:

   • Power distribution: upper left 120V/1300W； lower left 120V/1000W. (+ / – 10%).

5. Firepower adjustment: in heating mode, push the regulator, the digital gear from 1 to 9 is a normal heating gear, and the P gear is rapid heating. After 3 minutes, it will return to the 9 gear. Turn to 0 to
   stop heating.

6. Shutdown: In heating mode, long press heating and return to a shutdown state. the power button (long press for two seconds) to exit

7. Child lock: Press and hold the child lock button for 2-3 seconds, and the child lock can be locked or unlocked with a beep. After the lock is successful, the child lock number will display Lo, and the child lock can be operated in the power-off or standby heating state. After the lock is successful, do not operate any steps except the child lock.
   Locked successfully as shown in the figure:

8. Timing: This function is to set the shutdown time. In heating mode, press the timing button to enter the preset timing. The default time is 00 minutes. Button adjusting time (progressive 1 minute, 99 minutes at most), stop operation after adjustment, digital flashing several times into the steady setting success. Continuously press the timing button to set the time of multiple furnace areas. After the setting is completed, the small dot flashes at the lower right corner of the display digital number in the furnace area. The time display in different furnace areas automatically switches to about 5 seconds, with the small dot as a mark.
   As shown in the picture, the timing left the upper furnace area: 99 minutes

9. Panel high-temperature warning: there is still residual temperature on the furnace panel after use, warning display H, be careful of scalding hands.

10. The corresponding temperature of each section of fire (set the numerical value for the program), the measured data obtained by different working ring mirrors will have deviation.Range 1–2–3–4–5 –6–7–8–9–P ten stages.

Usable Pans

• All flat bottom pots.
• Please use iron pot, containing a magnetic pot.
• Please limit your food to 4kg.

Product dimensions and precautions

• Product size 28851082 (11.320.083.07 inches) If not including the foot of the fuselage thickness is 65MM/2.55 inches.
• Roar size 270490150mm (10.619.295.9 inches)

INSTALL ATION EASILY

Note: if the product is used on the table, because the bottom will produce temperature during the use process, please use high-temperature resistant flame retardant material for the table such as marble……. And so on.

Trouble Code And Troubleshooting

• E0——- no pot
• E1——- The voltage is lower than 60.
• E2——- Excessive voltage (voltage higher than 138)
• E3cuit
• E4
• E5
• E6——- The IGBT sensor is open
• E8——- The control board is connected to the main power supply board Voltage adaptation range: 70– 145 VOLTS

Heat Dissipation Structure Installation Drawing

When the machine is embedded, to ensure the normal use of the machine and better heat dissipation.
Requirements

1. 30-50mm heat dissipation should be left on the left and right sides and behind.
2. The counter interior should be as large as possible to ensure that enough cold air is sucked into the machine.
3. Inlet air (cold air) must be separated from outlet air (hot air) space.
4. The air inlet and outlet space of the counter leave air roar.

Front view

Side view

Installation

Owing to the high temperature inside the infrared cooker, make sure good ventiation is provided to assure its normal operation.

As shown in Figure 2

Attention

1. The electric hob is recommended to be installed by a professional. Please never conduct the operation by yourself.
2. The wall and heating area above the
3. To avoid danger the ceramic cooker hob must be installed into the cabinet before use.
4. Applicable cabinet material: wood, marble resin etc.

Safety Reminding

• Because the hob can temperature, please use a pot resistant to a temperature of over 200.
• After being used the corresponding heating zone of the ceramic cooker is still hot . Never touch the ceramic cooker
• If the power supply is damaged, it must be replaced by the agent or a similarly qualified person to avoid a hazard.
• A dedicated power protection air swith must be incorporated in the fixed wiring in accordance with the wiring rules.
• Never use the ceramic cooker hob in a high-temperature environment.
• Never wash the ceramic cooker hob with water directly. Steam cleaner is not to be used.
• Never have the cooker to work without food in the pot , otherwise its may be affected and danger may happen.
• For sealed foods such as canned goods , please do not heat them before opening their covers so as to avoid any dangers of explosion due to heating expansion.
• The appliance is not intended to be used by children or handicapped persons unless they have a responsible person to ensure they can use it safely.
• Do not place rough or uneven appliances, which may damage the
• pull-out of the plug to avoid the possibility of electric shock.
• Do not put any detergents or flammable materials in the equipment installed under the ceramic cooker hob.

This product should consider the following
Warning: ble electric shock.

Use of equipment by unattended young children and disabled children’s play equipment.

1. Do not overheat an empty pan.
2. Do not let children operate alone to avoid scalding and other risks.
3. During the operation of the appliance, the temperature of the
4. Do not use it in the bathroom, gas stove and other damp places or near inflammable and explosive objects.
5. Metal Objects Knives, forks, spoons and LIDS should not be pla area to prevent them from getting hot.
6. When using the equipment, it should be placed horizontally, not close to the wall or objects, with at least a clearance around it More than 30 cm.
7. indirectly, so as to avoid the high temperature of the bottom of the pot Cause combustion.
8. Do not directly add canned and other sealed containers, otherwise, the container will be heated and expanded, resulting in an explosion.
9. Do not heat the aluminum foil directly or indirectly.
10. This product is a household kitchen utensil and should not be used in industrial, medical and other places to avoid accidents.
11. Unplug the power cord plug from the socket to avoid electronic devices caused by long-time electricity Pieces of aging damage, even fire.
12. After cooking, there is still residual heat on the panel generated by the high temperature of the pot. Do not touch it immediately.
13. If the cord is damaged, it must be repaired by the manufacture ace.
14. Do not use POTS and pans with painted bottoms on the induction cooker to avoid high-temperature To burn.
15. Do not heat plastic containers and paper on panels to prevent burning.
16. Do not use the infrared cooker on the carpet or tablecloth, s
17. Do not heat food directly on the panel, especially high-fat food, overheating oil will Be lit.
18. The induction cooker cannot be operated by an external timer or independent remote control system.
19. Do not place the infrared cooker on the iron, stainless steel, aluminum and other metal panel, because The action of the magnetic field line will cause its heat induction cooker.
20. Do not flush with water directly to prevent the internal electronic components from water failure.

Cleaning And Maintenance

1. Please shut off the power and pull out the plug before cleaning of the appliance.
2. Clean the appliance until It cools down completely. e unit.
3. Do not clean by water directly, water gets Inside and may cause malfunction.
4. Keep the ceramic plate and pan clean before cooking, otherwise, clean and the plate may get discoloration. little limitless detergent with a toothbrush to clean.
5. Don’t use caustic Impregnates to clean. It may damage the cooker by chemical reaction. Do not use benzene, scrubbing brush or polishing powder to clean the Induction cooker.

Trouble Shooting

1. If there is anything wrong with the stove, please check it as follows before sending to repair.
2. Please do not open and repair the unit yourself to avoid getting
3. If you fail to Identify the problem, contact the after-sal

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>