LOGICDATA TOUCHfx CBItouch Family User Manual

CBItouch Family
Operating Manual

TOUCHfx CBItouch Family

Valid for:

• CBItouch C (TOUCHfx, TOUCHfx-KM, TOUCHdown)
• CBItouch I (TOUCHinlay-KM)

GENERAL INFORMATION

Documentation for the TOUCH Family consists of this Operating Manual and several other documents (Other applicable documents, page 5). Assembly personnel must read all documentation before starting assembly. Keep all documentation for as long as the product is in your possession. Ensure that all documentation is provided to subsequent owners. Go to www.logicdata.net for more information and support. This Manual may change without notice. The most recent version is available on our website.
1.1 OTHER APPLICABLE DOCUMENTS
This Operating Manual contains assembly instructions for the Handsets within the TOUCH Family. Other applicable documents include:

• Datasheet for the TOUCH Handset.
• Datasheet and Operating Manual for the Control Box in the Table System

1.2 COPYRIGHT
© January 2023 by LOGICDATA Electronic und Software Entwicklungs GmbH. All rights reserved, except for those listed in Chapter 1.3 Royalty-free use of images and text on page 5.
1.3 ROYALTY-FREE USE OF IMAGES AND TEXT
After purchase and full payment of the product, all text and images in Chapter 2 “Safety”, may be used free of charge by the customer for 10 years after delivery. They should be used to prepare end user documentation for Height- Adjustable Table Systems. The license does not include logos, designs, and page layout elements belonging to LOGICDATA. The Reseller may make any necessary changes to the text and images to adapt them for the purpose of end user documentation. Texts and images may not be sold in their current state, and may not be published or sublicensed digitally. The transfer of this license to third parties without permission from LOGICDATA is excluded. Full ownership and copyright of the text and graphics remain with LOGICDATA. Texts and graphics are offered in their current state without warranty or promise of any kind. Contact LOGICDATA to obtain text or images in an editable format ( documentation@logicdata.net ).
1.4 TRADEMARKS
Documentation may include the representation of registered trademarks of goods or services, as well as information about copyright or other proprietary expertise of LOGICDATA or third parties. In all cases, all rights remain exclusively with the respective copyright holder. LOGICDATA® is a registered trademark of LOGICDATA Electronic & Software GmbH in the USA, the European Union, and other countries.

SAFETY

2.1 TARGET AUDIENCE
This Operating Manual is intended for Skilled Persons only. Refer to Chapter 2.8 Skilled Persons on page 9 to ensure that personnel meet all requirements.
2.2 GENERAL SAFETY REGULATIONS
In general, the following safety regulations and obligations apply when handling the product:

• Do not operate the product unless it is in a clean and perfect condition
• Do not remove, change, bridge, or bypass any protection, safety, or monitoring equipment
• Do not convert or modify any components without written approval from LOGICDATA
• In the event of malfunction or damage, faulty components must be replaced immediately
• Unauthorized repairs are prohibited
• Do not attempt to replace hardware unless the product is in a de-energized state
• Only Skilled Persons are allowed to work with TOUCH Handsets
• Ensure that national worker protection conditions and national safety and accident prevention regulations are observed during operation of the system

2.3 INTENDED USE
The products in the TOUCH Family are Handsets for electrically Height- Adjustable Tables. They are installed by Resellers into Height-Adjustable Table systems. They are used to control Height-Adjustable Table systems via a Control Box. They are intended for indoor use only. They may only be installed in compatible Height Adjustable Tables and with LOGICDATA-approved accessories. Contact LOGICDATA for further details. Use beyond or outside the intended use will void the product’s warranty.
2.4 REASONABLY FORESEEABLE MISUSE
Usage outside of the intended use may lead to minor injury, serious injury, or even death. Reasonably foreseeable misuse of the Handset includes, but does not extend to:

• Connecting unauthorized parts to the product. If you are unsure as to whether a part can be used with a Handset, contact LOGICDATA for further information

2.5 EXPLANATION OF SYMBOLS AND SIGNAL WORDS
Safety Notices contain both symbols and signal words. The signal word indicates the severity of the hazard.
DANGER
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE
Indicates a situation which, if not avoided, could result in damage to the product through electrostatic discharge (ESD).
NOTICE
Indicates a situation that will not lead to personal injury, but could lead to damage to the device or the environment.
INFO
Indicates the protection class of the device: Protection Class III.
Protection Class III devices may only be connected to SELV or PELV power sources.
INFO
Indicates important tips for handling the product.
2.6 LIABILITY
LOGICDATA products comply with all currently applicable health and safety regulations. However, risk can result from incorrect operation or misuse. LOGICDATA is not liable for damage or injury caused by:

• Improper product use
• Disregard of the documentation
• Unauthorized product alterations
• Improper work on and with the product
• Operation of damaged products
• Wear parts
• Improperly performed repairs
• Unauthorized changes to the operating parameters
• Disasters, external influence, and force majeure

The information in this Operating Manual describes the characteristics of products without assurances.
Resellers assume responsibility for the LOGICDATA products installed in their applications. They must ensure their product complies with all relevant directives, standards, and laws. LOGICDATA shall not be held liable for any damage that is directly or indirectly caused by the delivery or use of this document.
Resellers must observe the relevant safety standards and guidelines for each product in the Table System.
2.7 RESIDUAL RISKS
Residual risks are the risks that remain after all relevant safety standards have been complied with. These have been evaluated in the form of a risk assessment. Residual risks associated with the installation of Handsets in the TOUCH Family are listed here and throughout this Operating Manual. See also Chapter 1.1 Other Applicable Documents on page 5. The symbols and signal words used in this Operating Manual are listed in Chapter 2.5 Explanation of Symbols and Signal Words on page 7.
WARNING
Risk of death or serious injury through electric shocks
TOUCH Handsets are electrical devices. Although you will not have to connect the Handset to the Control Box during assembly, basic safety precautions must be taken at all times. Failure to observe electrical safety precautions may lead to death or serious injury through electric shocks.

• Never open the Handset
• Ensure that the Handset is not connected to the Control Box during assembly
• Do not convert or modify the Handset in any way
• Do not immerse the Handset or its components in liquid. Clean only with a dry or slightly damp cloth
• Do not place the Cable of the Handset on heated surfaces
• Check the housing and cables of the Handset for visible damage. Do not install or operate damaged products.

WARNING
Risk of death or serious injury in explosive atmospheres
Operating the Handset in potentially explosive atmospheres may lead to death or serious injury through explosions.

• Read the relevant directives to determine if an atmosphere is potentially explosive
• Do not operate the Handset in potentially explosive atmospheres

CAUTION
Risk of minor or moderate injury through tripping
During the assembly process, you may have to step over Cables. Tripping over Cables may lead to minor or moderate injury.

• Ensure that the assembly area is kept clear of unnecessary obstructions
• Be careful not to trip over Cables

CAUTION
Risk of minor or moderate injury through crushing
If any Handset Key becomes stuck while the system is in motion, the system may not stop properly. This may lead to minor or moderate injury through crushing.

• Disconnect the system immediately if any Handset Key becomes stuck

CAUTION
Risk of injury through incorrect assembly
Only Skilled Persons have the expertise to complete the assembly process safely.
Assembly by Unskilled Persons may lead to minor or moderate injury.

• Ensure that only Skilled Persons are allowed to complete assembly
• Ensure that persons with limited ability to react to danger do not take part in the assembly process TOUCH Handsets may only be installed by Skilled Persons. A Skilled Person is defined as someone who:
• Is authorized for installation planning, installation, commissioning, or servicing of the product
• Has read and understood all documentation relevant to the Handset
• Has the technical education, training, and/or experience to perceive risks and avoid hazards
• Has knowledge of the specialist standards applicable to the product
• Has the expertise to test, assess, and manage electrical and mechatronic products and systems in accordance with the generally accepted standards and guidelines of electrical engineering and furniture manufacturing

2.9 NOTES FOR RESELLERS
Resellers are companies that purchase LOGICDATA products for installation in their own products.
INFO
For reasons of EU conformity and product safety, Resellers should provide end users with an Operating Manual in their native EU official language.
INFO
Operating Manuals must include all the safety instructions that end users require to handle the product safely. They must also include an instruction to always keep the Operating Manual in the immediate vicinity of the product.
INFO
No unauthorized persons (young children, persons under the influence of medications, etc.) should be allowed to handle the product.
INFO
Resellers must perform a risk assessment on their product that covers residual hazards.
It must include measures to mitigate risk, or reference the product‘s Operating Manual.

SCOPE OF DELIVERY

The standard scope of delivery for Handsets in the TOUCH Family consists of the Handset and its preattached cable. All other components necessary for installing the Handset (e.g. Mounting Screws for the TOUCHdown and TOUCHfx) must be supplied separately by the reseller.

UNPACKAGING

NOTICE
Ensure proper ESD handling during unpackaging. Damage that can be attributed to electrostatic discharge will void warranty claims.
To unpackage the product:

1. Remove all components from the packaging
2. Check the contents of the package for completeness and damage
3. Provide the Operating Manual to the operating personnel
4. Dispose of the packaging material

NOTICE
Dispose of the packaging material in an environmentally friendly manner. Remember to separate plastic parts from the cardboard packaging.

PRODUCTS

The TOUCH Family of Handsets consists of 3 products:

• TOUCHfx

This includes the Handsets TOUCHfx and TOUCHfx-KM (Key Membrane Version). In general, operation and assembly with both products is the same, with the exception of the Key Lock function, which is only available with the TOUCHfx. The instructions within this manual apply to both products, although only the TOUCHfx is depicted.

• TOUCHdown
• TOUCHinlay-KM

INFO
Each Handset may have several variants. Variants may be equipped with additional features or different configurations. The exact variant is denoted by the product‘s order code. Consult the accompanying Datasheet to check ensure that you have received the correct variant.
5.1 KEY PRODUCT FEATURES
5.1.1 TOUCH-FX

Fig. 1: Product features, TOUCHfx

1. UP / DOWN Keys
2. Memory Position Keys
3. SAVE Key
4. Display
5. Drilling Holes
6. Strain Relief

INFO
The image is representative and depicts the TOUCHfx (not TOUCHfx-KM)
5.1.2 TOUCH-DOWN

*Cable not shown.
Fig. 2: Product features, TOUCHdown

1. UP / DOWN Keys
2. Memory Position Keys
3. SAVE Key
4. Display
5. Drilling Holes
6. Supports for Cable Loop

5.1.3 TOUCH-INLAY-KM

1. UP / DOWN Keys
2. Memory Position Keys
3. SAVE Key
4. 3-Segment Display
5. Rubber Ribs

*Cable not shown.
Fig. 3: Product features, TOUCHinlay-KM

5.2 DIMENSIONS
5.2.1 TOUCHFX

Length| 85.9 mm | 3.380”
---|---
Width| 132.5 mm | 5.216”
Height| 32.8 mm | 1.289”

Fig. 4: Product dimensions, TOUCHfx

5.2.2 TOUCH-DOWN

Length| 150.3 mm | 5.917”
---|---
Width| 183.6 mm | 7.228”
Height| 38.8 mm | 5.917”

5.2.3 TOUCHINLAY

Length| 42.0 mm | 1.654”
---|---
Width| 95.4 mm | 3.756”
Height| 20.3 mm | 0.799”

5.2.4 DIMENSIONS FOR THE MILLED CUT-OUT
The milled cut-out for the TOUCHinlay-KM shall have the following dimensions (image to scale):

INFO
It is assumed that the milled cut-out will pass through the entire table top (i.e. milling will create a hole rather than an indent). If you do not mill through the entire Table Top,
you will need to drill a separate hole to accomodate the TOUCHinlay-KM‘s cable. In this case, contact LOGICDATA for further information on dimensions.
5.3 DRILLING TEMPLATES
5.3.1 TOUCHFX

5.3.2 TOUCH-DOWN

ASSEMBLY

This chapter describes the process of installing the TOUCH Family Handset into the Height-Adjustable Table System.
6.1 SAFETY DURING ASSEMBLY
The following safety instructions are valid for each Handset within the TOUCH Family. Hazards relating only to the installation of a specific Handset are listed in that Handset‘s assembly instructions.
CAUTION
Risk of minor or moderate injury through improper handling
Improper handling of the product during assembly may lead to minor or moderate injury through cutting, pinching, and crushing.

• Avoid contact with sharp edges
• Be careful while handling tools that may cause personal injury
• Ensure assembly complies with the generally accepted standards and guidelines of electrical engineering and furniture manufacturing
• Read all instructions and safety advice carefully

CAUTION
Risk of minor or moderate injury through tripping
During assembly and operation, poorly routed Cables may become a trip hazard.
Tripping over Cables may lead to minor or moderate injury.

• Ensure that Cables are routed properly to avoid trip hazards
• Be careful not to trip over Cables when installing the Handset

NOTICE
Ensure proper ESD handling during assembly. Damage that can be attributed to electrostatic discharge will void warranty claims.
NOTICE
To avoid damage to the product, measure the dimensions of the Handset before assembly.
NOTICE
Before assembly, all parts must be acclimatised to the ambient conditions.
NOTICE
Do not lift the Handset by its cable. This will cause irreparable damage to the product.
INFO
Perform a product risk assessment so that you can respond to potential residual hazards. Assembly instructions must be included in your end user Operating Manual.
6.2 ASSEMBLY: TOUCHFX
6.2.1 REQUIRED COMPONENTS

INFO
Screw specifications
Thread diameter: max. 5 mm | Head diameter: 8.5 mm – 10.6 mm If possible, do not use countersunk-head screws.
6.2.2 PROCESS

1. Position the Handset under the table top and mark the position of the drilling holes. If necessary, use the Drilling Template in chapter 5.3.1 to help you.

2. Insert the Strain Relief into the designated slot on the Handset (Fig. 6).
   NOTICE
   Inserting the Strain Relief incorrectly may cause damage to the Cable and Handset.
   Ensure that the Cable does not protrude over the housing

3. Use the screwdriver and 2 Mounting Screws to attach the Handset to the Table Top at the marked drilling points.
   NOTICE
   The required tightening torque depends on the material of the Table Top. Do not exceed 2 Nm.

6.2.3 COMPLETING ASSEMBLY
After the TOUCHfx is attached to the Table Top, you must connect the Cable to the Control Box. Refer to the manual for your chosen Control Box for instructions.
6.3 ASSEMBLY: TOUCHDOWN
6.3.1 REQUIRED COMPONENTS
The following components are required to assemble the TOUCHdown

INFO
Screw specifications
Thread diameter: max. 5 mm | Head diameter: max. 10 mm If possible, do not use countersunk-head screws.
6.3.2 PROCESS

1. Position the Handset under the table top and mark the position of the drilling holes (Fig. 11).
   Alternatively, use the Drilling Template in Chapter 5.3.2 to help you. Ensure that the corners circled in the diagram below are flush with the edge of the Table Top.
   INFO
   If the mounting area has a curved edge, move the Handset slightly backwards.

2. Ensure the cable is routed correctly. For correct operation, a 10cm Cable Loop must be routed.
   Use the Cable supports on the back edge of the Control Box to help you do this (Fig. 12).

3. Use the screwdriver and 4 Mounting Screws to attach the Handset to the Table Top at the marked drilling points.
   NOTICE
   The required tightening torque depends on the material of the Table Top. Do not exceed 2 Nm.

6.3.3 COMPLETING ASSEMBLY
After the TOUCHdown is attached to the Table Top, you must connect the Cable to the Control Box. Refer to the manual for your chosen Control Box for instructions.
6.4 ASSEMBLY: TOUCHINLAY-KM
6.4.1 REQUIRED COMPONENTS
The following components are required to assemble the TOUCHinlay-KM:

6.4.2 PROCESS

1. Use a milling cutter or similar to mill the cut-out. The dimensions for the milled cut-out are shown in Chapter 5.2.4 (Fig. 7).
2. Push the Handset into the milled cut-out until the top plate is flush with the Table Top. The rubber ribs will hold the Handset in place.

6.4.3 COMPLETING ASSEMBLY
After the TOUCHinlay-KM is attached to the Table Top, you must connect the Cable to the Control Box. Refer to the manual for your chosen Control Box for instructions.

OPERATION

CAUTION Risk of minor or moderate injury through uncontrolled movement The table may not always stop exactly at the expected position. Failure to anticipate the table‘s movements may lead to minor or moderate injury through crushing.

• Wait until the system has completely stopped before attempting to use the table

CAUTION Risk of minor or moderate injury through unsecured objects
While the table moves up and down, unsecured objects may fall off the table and onto body parts. This may lead to minor or moderate injury through crushing.

• Ensure loose objects are kept away from the edge of the table
• Do not leave unnecessary objects on the table during movement

CAUTION Risk of minor or moderate injury through crushing
Failure to release Handset Keys correctly may result in the table failing to stop properly.
This may lead to minor or moderate injury through crushing.

• Do not slide your finger to a different Handset key while another button is pressed
• Disconnect the system immediately if any Handset Key becomes stuck

INFO
The technology within the Handset may be interrupted by external interferences during operation. This may lead to certain user inputs (i.e. button presses) not being recognized.
This section of the Operating Manual contains a selection of instructions for operating the Table System to which the TOUCH Handset is connected. TOUCH Handsets are compatible with a large number of LOGICDATA Control Boxes. Before using the Table System, you must also read the Operating Manual for the installed Control Box, including all relevant safety information, in full.
Handset Keys are represented as follows for further description:

| UP Key
---|---
DOWN Key
SAVE Key
Memory Position Key 1
Memory Position Key 2
Memory Position Key 3
Memory Position Key 4

7.1 ADJUSTING THE TABLE TOP HEIGHT
CAUTION
Risk of minor or moderate injury through crushing
Your fingers may be crushed when you attempt to change the height of the table.

• Keep fingers away from moving parts
• Ensure that no persons or objects are in the table‘s range of motion

INFO
The Table Top will move up or down until the UP or DOWN Key is released, or if a predefined stopping point has been reached.
To move the Table Top UP:
Press and hold the UP Key until the desired height has been reached
To move the Table Top DOWN:
Press and hold the DOWN Key until the desired height has been reached
7.2 SAVING A MEMORY POSITION
This function saves a set Table Top position. One Memory Position can be saved per Memory Position Key.

| 1. Move the table to the desired height
---|---
 ▸ The display shows the Table Top height (e.g. 73 cm)
2. Press the SAVE Key
3. Press the Memory Position Key (e.g. 2)
 ▸ The display shows S 2
 ▸ After about two seconds, the Table Top height is displayed again

7.3 ADJUSTING THE TABLE TO A MEMORY POSITION
Version A (without double-click function):

| 1. Press and hold the required Memory Position Key (e.g. 2).
---|---
|  ▸ The Table Top will move until the saved Table Top height has been reached. If you release the Key before the Memory Position is reached, the table will stop.
| 2. Release the Memory Position Key
|  ▸ The display shows the Table Top height (e.g. 73 cm)

Version B (Auto-Movement with double-click function):
INFO
The double-click function is available only for Table Systems sold in US markets.
INFO
If you press any Key while the table moves to a Memory Position, the Table Top will stop moving immediately. To continue, you must select the Memory Position again.
CAUTION
Risk of minor or moderate injury through unauthorized modifications
The firmware is delivered with a deactivated double-click function. If you activate this
function, the grading of the safety functions according to EN ISO 13849-1 PL b, Category B, are no longer valid, as the legal requirements in the standard are no longer met.

• If you activate the function, perform a new risk new assessment to meet the higher safety requirements (EN 60335-1). These cannot be met by LOGICDATA Control Boxes.
• LOGICDATA is not liable for injuries or damage caused by activating the doubleclick function

| 1. Double-click the required Memory Position Key (e.g. 2)
---|---
|  ▸ The table will move to the Memory Position. You do not have to hold the Key
|  ▸ The display shows the Table Top height (e.g. 73 cm)

7.4 KEY LOCK
CAUTION
Risk of minor or moderate injury through uncontrolled movement
When attempting to activate the Key Lock, pressing the Handset too forcefully may cause the table to move unexpectedly. Failure to anticipate the table‘s movements may lead to minor or moderate injury through crushing.

• Do not press the Handset too forcefully while activating the Key Lock

INFO
The Handset must be turned on for the Key Lock to be activated. To activate a locked Handset, press any key.
INFO
The Key Lock is only available as standard on certain models of the TOUCHfx and TOUCHdown. On other models it can be activated during parameterization. Check the Order Code for your Handset to see if Key Lock is activated as standard.
Please note that the Key Lock is not available for the TOUCHfx-KM or TOUCHinlay-KM.
Activating the Key Lock prevents you from moving the table if you accidentally press a Key. The Key Lock can be activated and deactivated by swiping across the bottom edge of the Handset. Alternatively, swipe horizontally across the left or right-hand side of the Handset (figure 5, Activating the Key Lock). The display must be active for you to activate the Key Lock. To activate an inactive display, press any Key.

After you have activated the Key Lock, a key is displayed on the screen.

7.5 OPERATION: NOTES FOR TOUCHDOWN
The following information applies only to the TOUCHdown Handset. If you have a different Handset,
proceed to the next chapter.
7.5.1 PUSH-PUSH FUNCTION
NOTICE
To avoid product damage, ensure a 10 cm Cable Loop is routed (Chapter 6.3.2, Fig. 12)
The Push-Push Function allows the TOUCHdown to be slid underneath the table when not in use, and move outwards to the operating position when it is needed.
To move the TOUCHdown into the operation position:

1. Push the Handset towards the Table Top and release.
   ▸ The Handset will click when it is unlocked from its housing

2. Allow the Handset to slide out from underneath the table.

NOTICE
To avoid product damage, do not pull on the Handset while attempting to move it to the operation position.
To stow the TOUCHdown underneath the table:

1. Lift the control panel of the Handset gently upwards until it is level with its housing.
2. Push towards the table top until the Handset clicks into position.

7.5.2 MECHANICAL RELEASE
If excessive force is applied to the Control Panel of the TOUCHdown, it will be released automatically from its housing to prevent system damage.
To re-attach the Control Panel:

1. Align the springs on the Control Panel with the sliding mechanism of the housing.
2. Push the outer edges of the Control Panel firmly towards the housing to click it back into place.

ADDITIONAL INFORMATION

8.1 SOFTWARE-DEPENDENT FUNCTIONS
A full list of Software-Dependent Functions can be found in the Operating Manual of the installed Control Box.
8.2 DISASSEMBLY
To disassemble your Handset, ensure that it has been disconnected from the Power Unit. Then, follow the assembly instructions in reverse order.
8.3 MAINTENANCE
All Handsets in the TOUCH Family are maintenance-free for their entire service lifetime.
WARNING
Risk of death or serious injury through electric shocks and other hazards
Using a Handset alongside unauthorized spare or accessory parts may lead to death or serious injury through electric shocks and other hazards.

• Only use accessory parts produced or approved by LOGICDATA
• Only use replacement parts produced or approved by LOGICDATA
• Only allow Skilled Persons to perform repairs or install accessory parts
• Contact customer services immediately if the system malfunctions
  The use of unauthorized spare or accessory parts may cause system damage. Warranty claims are void in this scenario.

8.3.1 CLEANING

1. Disconnect the height-adjustable desks power supply from the power source.
2. Wait 30 seconds for residual voltage to dissipate.
3. Wipe the surface of the Handset with a dry soft cloth or a soft cloth lightly moistened in water. Never immerse the Handset into any liquid.
4. Wait for the Handset to dry completely.
5. Reconnect the power supply.

8.3.2 REPLACING A HANDSET

1. Disconnect the Control Box from the Mains.
2. Disconnect the Handset from the Control Box.
3. Remove the Handset from the Table Top.
4. Mount the new Handset onto the Table Top.
5. Plug the Handset back into the Control Box.
6. Reconnect the Control Box to the Mains.

8.4 TROUBLESHOOTING
Usually, malfunctions occur when Handsets are pressed while calibrating. If the Handset fails to function, you will need to restart the system. To do this:

1. Unplug the Handset from the Control Box.
2. Plug the Handset back to the motor Control Box.
3. After a few seconds the Handset is ready for operation.

A list of common problems and their solutions can be found in the Operating Manual of the installed Control Box.
8.5 DISPOSAL
All products in the TOUCH Family are subject to the WEEE Directive 2012/19/EU.

• Dispose of all components separately from household waste. Use designated collection points or disposal companies authorized for this purpose

LOGICDATA
Electronic & Software Entwicklungs GmbH
Wirtschaftspark 18
8530 Deutschlandsberg
Austria
LOGICDATA North America, Inc.
1525 Gezon Parkway SW, Suite C
Grand Rapids, MI 49512
USA

Phone: +43 (0)3462 5198 0
Fax: +43 (0)3462 5198 1030
E-mail: office.at@logicdata.net
Internet: http://www.logicdata.net
Phone: +1 (616) 328 8841
E-mail: office.na@logicdata.net
www.logicdata.net
TOUCH Family – Operating Manual
Document Version 7.0 / January 2023
This document was originally published in English
LOGICDATA Electronic & Software Entwicklungs GmbH
Wirtschaftspark 18
8530 Deutschlandsberg
Austria
Telefon: +43 (0) 3462 51 98 0
Fax: +43 (0) 3462 51 98 1030
Internet: www.logicdata.net
Email: office.at@logicdata.net

Documents / Resources

| LOGICDATA TOUCHfx CBItouch Family [pdf] User Manual
TOUCHfx CBItouch Family, TOUCHfx, CBItouch Family, Family
---|---

References

• LOGICDATA | Mechatronic Solutions for Every Industry LOGICDATA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>