BRANDMOTION 212FVMR171 FullVUE Rear Camera Mirror Instruction Manual
- June 9, 2024
- BRANDMOTION
Table of Contents
FullVUE®️ Rear Camera Mirror for
RAM 1500 (2019-Current)
FVMR-1171
Instruction Manual
212FVMR171 FullVUE Rear Camera Mirror
Recommended Tools
Difficulty Level | Install Time |
---|---|
45m – 75m |
Questions? Call the Brandmotion technical support line at 734-619-1250 or CLICK HERE
Kit Contents
Components for installing the FVMR-1171 Kit Contents:
- FullVUE® Mirror & Harness
- 3rd Brake Light Bezel & Camera
- 9m Camera Harness
Installation of the FullVUE Mirror
Part 1
Installation of the FullVUE Mirror and wire connections
- Remove the old mirror on the windshield by turning the mirror mount 90 degrees clockwise .
- Install new FullVUE mirror onto the mirror mount on a bench. Remove the screw connecting the end of the stem & the screw connecting the mirror mount.
- Connect the new mirror mount to the FullVUE Mirror.
- Once connected, reinstall the mount to the vehicle by twisting 90 degrees counterclockwise.
Part 2
Powering the FullVUE Mirror
- Connect the power harness to the plug on the mirror. Route the harness across the top of the head liner, along the windshield, and down the A-pillar, and to the desired location in the kick panel.
- Ensure that the harness will not be pinched when trim panels are replaced.
Part 3
Wiring the FullVUE Mirror
- Connect the RED wire from the mirror harness to 12-volt accessory power.
- Connect the YELLOW wire from the mirror harness to 12-volt constant power.
- Connect the BLACK wire to a solid ground. Chassis ground in the kick panel is recommended.
Part 4
Function test of the FullVUE Mirror
- Turn the vehicle ignition on and see if you are seeing the front camera displayed on the screen. Turn off the ignition and the mirror will power down
Disassembly
Part 1
Removing the third brake light
- Use a Phillips screwdriver to remove the screws on either side of the brake light.
- Pull the brake light out from the cab. Be Careful not to damage the foam gasket around the opening.
- Disconnect the power connector from the light.
Running Wires
Part 1
Video Connector
- Connect the 9m camera harness to the mirror harness at the connection by the mirror.
- Run the 9m camera harness from the FullVUE Mirror through the headliner toward the brake light.
- Pull the video connector of the 9m camera harness through the grommet to the outside of the cab.
Assembly
Part 1
Assembling the Bezel.
-
Attach the thick foam gasket to the back side of the bezel or to the light. Whichever piece does not have a foam gasket from the factory.
Note: The cable for the camera must go through the channel of the bezel before the foam is put overtop -
Put the foam side of the bezel against the vehicle.
-
Connect the rear camera harness to the camera. Make sure to line up the arrows on the connectors
-
Plug the brake light back into the cab plug
-
Put the screws through the hole of the light and insert the light into the bezel.
-
Use the screws that are showing through the bezel to line up with the screw holes of the vehicle. ( Be careful not to scratch the vehicle.)
-
Screw the assembly back together with the factory screws.
Adjustment
Part 1
- If you need to change the camera’s pitch, gently bend the bracket until it reaches the desired view angle.
Vehicle Application:
RAM 1500 (2019-Current)
Part Number: FVMR-1171
AR_1_10_23
FullVUE®️ Rear Camera Mirror – FVMR-1171
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>