PHILIPS SPC1234AT-27 Outdoor Lighting Control Socket with Remote Control User Guide

PHILIPS SPC1234AT-27 Outdoor Lighting Control Socket with Remote Control

FCC STATEMENT

Suppliers Declaration of Conformity | Model #: NOA0025, SPC1234AT/27| Jasco Products Company LLC, 10 e memorial road Office oklahoma city, OK 73114

www.byjasco.com

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

RISK OF ELECTRIC SHOCK:

• FULLY INSERT THE PLUG INTO A GFCI CONTROLLED RECEPTACLE
• KEEP CHILDREN AWAY
• DO NOT USE WITH EXTENSION CORDS
• INSTALL TIMER AS FAR ABOVE GROUND LEVEL AS POSSIBLE WITH THE RECEPTACLE FACING DOWNWARD
• NOT FOR WATER IMMERSION OR FOR USE WHERE DIRECTLY EXPOSED TO DRIPPING OR SPLASHING WATER
• UNPLUG BEFORE CLEANING

RISK OF FIRE:

• DO NOT EXCEED ELECTRICAL RATINGS
• DO NOT USE TO CONTROL APPLIANCES THAT CONTAIN HEATING ELEMENTS (COOKING APPLIANCES, HEATERS, IRONS, ETC)

BATTERY WARNING:

• BATTERIES MAY LEAK HARMFUL LIQUIDS OR IGNITABLE MATERIALS OR EXPLODE CAUSING INJURY OR PRODUCT DAMAGE
• DO NOT MIX OLD AND NEW OR OTHER BATTERY TYPES
• REPLACE ALL BATTERIES AT THE SAME TIME
• REPLACE FULLY DISCHARGED BATTERIES IMMEDIATELY
• REMOVE BATTERIES IF PRODUCT IS TO BE UNUSED FOR AN EXTENDED PERIOD OF TIME

RECEIVER

Functional Range…… Up to 80 ft.
Maximum Tungsten Load…… 1000 W, 8 A
Maximum Resistive Load…… 1875 W, 15 A
Rating……125 VAC/60 Hz

TRANSMITTER

Functional Range…… Up to 80 ft.
Battery Type…….. Use only CR2032 battery

Functional range may be adversely affected by one or more of the following factors: weather, radio frequency interference, low transmitter battery, and obstructions between the transmitter and receiver

Product description

A. Outdoor timer
Plug the device(s) to be controlled into the grounded outlet(s) on the bottom of the outdoor timer.
B. Wireless remote transmitter
Press the ON button on the remote to turn on the lamp(s) or device(s) plugged into the timer. Press the OFF button to turn fixture(s) off.
See installation instructions.

Installation instructions

Mounting the timer

1. Mounting the timer
   • Mount the timer (A) onto a wall near a GFCI outlet.
   • Install a nail or screw (not included) into a wall.
   
   The nail or screw must extend at least 7/8in. from the wall and allow the timer to be above ground level as far as possible.
   • Hang the timer (A) from the eyelet on the top left of the unit with the receptacles (D) facing downward so moisture does not accumulate.
   • Plug the grounded power cord (C) into a GFCI outlet.
   • Plug the device you wish to control into either receptacle (D).
   

2. Preparing the remote:
   • Pull the plastic tab on the remote to activate battery.

3. Plug in the timer and press the remote’s ON button. The timer should turn on.

4. Pairing remote and timer:
   Timer should be paired to the remote, but if it does not work:
   • Plug in the timer, and within five seconds, unplug it. Repeat this process three times until the red indicator light flashes.
   • Press any button on the remote. The red indicator light on the timer stops flashing when pairing is successful.

5. Changing the battery (B):
   • Remove the Phillips screw and slide the battery cover from the remote.
   • Remove the battery and insert a new CR2032 battery — note polatiry.
   • Replace the cover and screw.
   

Troubleshooting

1. If the indicator light is not activated by pressing the button, check the following:
   • Ensure the button is pressed and held for at least one second.
   • Verify the battery orientation, noting the polarity.
   • Replace the battery. Use only CR2032.

2. The device does not turn on
   • Ensure the lamp or electronic device plugged into the timer is turned ON.
   • Ensure the AC power cord is securely plugged into an AC power outlet.

ISED Statement

This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES 3 (B)/NMB 3(B).

CUSTOMER SUPPORT

READ IT OR WATCH IT

|
Read instructions or watch easy-to-follow video. Scan QR code or visit https://byjasco.com/44873i

byjasco.com/recycle paper made from 25% post consumer waste

MADE IN VIETNAM
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips N.V. and are used under license. This product has
been manufactured by and is sold under the responsibility of Jasco
Products Company, and Jasco Products Company LLC, 10 E.
Memorial Rd., Oklahoma City, OK 73114 is the warrantor in relation
to this product.
This product has a 1-year limited warranty.
Visit www.philips.com/support for warranty details.
Questions? Contact our U.S.-based Consumer Care
at 1-844-816-0320, M-F, 7AM-8PM Central Time.
For product patent information, visit
www.byjasco.com/patents.

References

• Recycling Matters at Jasco
• Philips Customer Service Support - Home | Philips
• Jasco
• Patents
• Philips Customer Service Support - Home | Philips
• YouTube

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>