BRANDMOTION FVMR-1181 FullVUE Rear Camera Mirror User Manual
- June 9, 2024
- BRANDMOTION
Table of Contents
Fuller® Rear Camera Mirror for Ford
F-150 (2015-Current) & Super Duty
(2017-Current) FVMR-1181
FVMR-1181 FullVUE Rear Camera Mirror
| Recommended Tools | Difficulty Level |
|---|
|
Install Time
Kit Contents
Components for installing the FVMR-1181
Kit Contents:
Fuller® Mirror & Harness
3rd Brake Light Bezel & Camera
9m Camera Harness
Installation of the Fuller Mirror & Wire Connections
If the truck has a forward facing camera in the plastic housing behind the rearview mirror then skip to Part 1b.
| Part 1a | Attaching the Fuller Mirror to the windshield |
|---|
1. Remove the old mirror from the mount on the windshield as per
manufacturer’s directions.
Be sure to use the proper removal tool if required.
2. Install new mirror onto the D-tab and tighten with a Phillips
screwdriver.
Take care not to overtighten.
Overtightening could result in damage to your windshield.| 
Part 1b| These steps are for trucks with a forward facing camera in the
plastic housing behind the rearview mirror.
---|---
- Remove the old mirror on the windshield by turning the mirror mount 90 degrees clockwise.
- Install new Fuller mirror onto the mirror mount on a bench. Remove the screw connecting the end of the stem & the screw connecting the mirror mount.
- Connect the new mirror mount to the Fuller Mirror.
- Remove the forward facing camera from the factory mirror stem and attach it to the new mirror stem using the factory screws.
- Remove the factory twist on the 3-pronged mounting foot from the factory stem by removing the screw.
- Attach the 3-pronged mounting foot in the same location on the new stem, use the supplied screw.
- Once connected, reinstall the mount to the vehicle by twisting 90 degrees counterclockwise.
|
Installation of the Fuller Mirror & Wire Connections
| Part 2 | Powering the Fuller Mirror |
|---|
1. Connect the power harness to the plug on the mirror. Route the harness
across the top of the head liner, along the windshield, and down the A-pillar,
and to the desired location in the kick panel
2. Ensure that the harness will not be pinched when trim panels are
replaced.|
Part 3| Wiring the Fuller Mirror
---|---
1. Connect the RED wire from the mirror harness to 12-volt accessory power.
(PHOTO) Need factory wire color
2. Connect the YELLOW wire from the mirror harness to 12-volt constant
power. (PHOTO Need factory wire color
3. Connect the BLACK wire to a solid ground.
Chassis ground in the kick panel is recommended. (PHOTO)| 
Part 4| Function test of the Fuller Mirror
---|---
1. Turn the vehicle ignition on and see if you are seeing the front camera
displayed on the screen. Turn off the ignition and the mirror will power down|
Disassembly
| Part 1 | Removing the third brake light |
|---|
1. Use a Phillips screwdriver to remove the screws on either side of the
brake light
2. Pull the brake light out from the cab. Be Careful not to damage the foam
gasket around the opening.
3. Disconnect the power connector from the light.|
Running Wires
| Part 1 | Video Connector |
|---|
1. Connect the 9m camera harness to the mirror harness at the connection by
the mirror.
2. Run the 9m camera harness from the Fuller Mirror through the headliner
toward the brake light.
3. Pull the video connector of the 9m camera harness through the grommet to
the outside of the cab.| 
Assembly
| Part 1 | Assembling the Bezel |
|---|
1. Attach the thick foam gasket to the back side of the bezel or to the
light. Whichever piece does not have a foam gasket from the factory.
Note: The cable for the camera must go through the channel of the bezel
before the foam is put overtop
2. Put the foam side of the bezel against the vehicle.
3. Connect the rear camera harness to the camera. Make sure to line up the
arrows on the connectors
4. Plug the brake light back into the cab plug
5. Put the screws through the hole of the light and insert the light into the
bezel.
6. Use the screws that are showing through the bezel to line up with the
screw holes of the vehicle. ( Be careful not to scratch the vehicle.)
7. Screw the assembly back together with the factory screws.| 
Adjustment
|
---|---
1. If you need to change the camera’s pitch, gently bend the bracket until it
reaches the desired view angle.|
Vehicle Application:
Ford F-150 (2015-Current) &
Super Duty (2017-Current)
Part Number: FVMR-1181
FullVUE® Rear Camera Mirror – FVMR-1181
Documents / Resources
|
BRANDMOTION FVMR-1181 FullVUE Rear Camera
Mirror
[pdf] User Manual
FVMR-1181 FullVUE Rear Camera Mirror, FVMR-1181, FullVUE Rear Camera Mirror,
Rear Camera Mirror, Camera Mirror, Mirror
---|---
|
BRANDMOTION FVMR-1181 FullVUE Rear Camera
Mirror
[pdf] Instruction Manual
FVMR-1181 FullVUE Rear Camera Mirror, FVMR-1181, FullVUE Rear Camera Mirror,
Rear Camera Mirror, Camera Mirror, Mirror
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>