RP LIGHTING FANS 1RP88 LED Ceiling Fan Light Kit Instruction Manual
- June 9, 2024
- RP LIGHTING FANS
Table of Contents
RP LIGHTING FANS 1RP88 LED Ceiling Fan Light Kit
Product Information
- Product Name: 1RP88 Ceiling Fan
- Model Number: T 24 JA8-2019
- Compliance: Compliant with industry standards
Product Usage Instructions
- Step 1: Attach the switch housing (1) to the ceiling fan using the attachment screws (9).
- Step 2: Connect the blue wire (3) from the ceiling fan to the blue wire from the light kit (5) using a wire nut (4).
- Step 3: Connect the white wire (10) from the ceiling fan to the white wire from the ceiling using a wire nut (4).
- Step 4: Connect the white wire (11) from the light kit to the white wire from the ceiling using a wire nut (4).
- Step 5: Attach the switch housing cap (6) to the switch housing (1) using the hex nut (7) and spring washer (8).
- Step 6: Attach the thread nipple (12) to the switch housing cap (6).
- Step 7: Attach the light fixture pan (14) to the thread nipple (12).
- Step 8: Install the plug button (13) into the opening on the switch housing cap (6).
- Step 9: Use the ceiling fan switch chain (2) to control the fan speed and turn on/off the light fixture.
_ Note: _These instructions are for general guidance only. Please refer to the product manual for detailed instructions specific to your model.
PACKAGE CONTENTS
- (1x) Light Fixture
- (2x) Wire Nut
- (1x) Acrylic Lens
READ AND FOLLOW SAFETY INSTRUCTIONS
WARNING: Turn off the main power at the circuit breaker before installing and servicing the fixture to prevent possible injury from electric shock.
CAUTIONS
- All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) Standards.
- If you are unfamiliar with proper electrical wiring connections, obtain the services of a qualified electrician.
- Use minimum 90’C supply conductors.
- All parts must be used as indicated in these instructions. DO NOT substitute any parts, leave parts out or use any parts that damaged. Failure to follow instruction could invalidate safety listing and warranty of this fixture.
- Carefully hold the fixture, do not apply pressure to the fixture body.
PREPARATION
- Unpack new fixture and remove all parts on a clean area.
- Be sure not to lose any small parts and mounting screws necessary for installation.
INSTALLATION & ASSEMBLY
ATTACHING LIGHT KITTO FAN SWITCH HOUSING
- Light kit can be installed in one of two ways.
- Installation on fans with detachable switch housing (Fig.1) or fans with non-detachable switch housing.(Fig2)
- Remove the switch housing cap(6) or switch housing(l) by unscrewing three attachment screws(9).
- Remove the plug button(l 3) from the center hole of cap.(Fig.2) Remove the plug button from the detachable switch housing (Fig.1)
NOTE
- Keep the plug button, shall you choose to remove the light kit fixture in the near future.
- Install spring washer(8) and hex nut(7) onto the threaded nipple(l 2) from light kit to secure the switch housing cap(6) or switch housing(l ).
- Be sure it is secured enough to prevent screws from vibrating loose.
MAKING WIRE CONNECTIONS
- Locate two wires in switch housing, white and blue, labeled “For Light”.
- Connect blue wire from fan(3) to Black wire from Light kit(S), white wire from fan(l 0) to white wire from Light kit(l 1) using wire nuts(4).
- After completing wires connection, carefully tuck wires back into fan switch housing.
- Attach the switch housing cap(6) with light kit assembly to fan switch housing(l) with three attachment screws(9) removed from switch housing.
WARNING
- Improper installation could cause the light fixture to fall, or result in electrical shock or personal injury.
- Installation is complete and you can restore power to the ceiling fan and operate.
Replacement: This integrated LED fixture has no bulb to replace.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>