RP LIGHTING FANS 1RP84 LED Ceiling Fan Light Kit Instruction Manual

RP LIGHTING FANS 1RP84 LED Ceiling Fan Light Kit

Product Information

Model: 1RP84

T24 JA8-2019 Compliant

This product is a light kit designed to be attached to a ceiling fan. It comes with a glass shade and a wood tassel for the pull chain.

The installation should be done by a qualified electrician in accordance with local and National Electrical Code (N.E.C.) Standards. All electrical connections must be done with the main power off at the circuit breaker to prevent possible injury from electric shock.

Product Usage Instructions

Step 1: Unpack the new fixture and remove all parts on a clean area, making sure not to lose any small parts and mounting screws necessary for installation.

Step 2: Attach the light kit to the fan switch housing. The light kit can be installed in one of two ways: for fans with detachable switch housing or non-detachable switch housing. Follow the instructions provided in the user manual for attaching the light kit to the specific type of fan.

Step 3: Make wire connections. Locate two wires in switch housing, one white and one blue, labeled “For Light”. Connect blue wire from fan to black wire from light kit, and white wire from fan to white wire from light kit using wire nuts. After completing the wire connection, carefully tuck wires back into fan switch housing.

Step 4: Install the glass shade and wood tassel. Raise the glass shade into light fixture pan and secure it with three thumb screws. Attach the provided wood tassel to the light kit pull chain. Pass the ceiling fan switch chain through another side hole of the light fixture pan, and re-attach the ceiling fan pull chain.

Warning: Improper installation could cause the light fixture to fall or result in electrical shock or personal injury. Follow all instructions carefully to ensure a safe and secure installation.

LED Ceiling Fan Light Kit
Model: 1RP84
READ AND FOLLOW

SAFETY INSTRUCTIONS

WARNING : Turn off the main power at the circuit breaker before installing and servicing the fixture to prevent possible injury from electric shock.
CAUTIONS-

1. All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) Standards.
2. If you are unfamiliar with proper electrical wiring connections, obtain the services of a qualified electrician.
3. Use minimum 90°C supply conductors.
4. All parts must be used as indicated in these instructions. DO NOT substitute any parts, leave parts out or use any parts that damaged. Failure to follow instruction could invalidate safety listing and warranty of this fixture.
5. Carefully hold the fixture, do not apply pressure to the fixture body and hold glass shade with care.

PREPARATION

Unpack new fixture and remove all parts on a clean area.
Be sure not to lose any small parts and mounting screws necessary for installation.

INSTALLATION & ASSEMBLY

STEP 1. ATTACHING LIGHT KIT TO FAN SWITCH HOUSING

• Light kits can be installed in one of two ways.
• Installation on fans with detachable switch housing (Fig.1) or fans with non-detachable switch housing.(Fig.2)
• Remove the switch housing cap(6) or switch housing(1) by unscrewing three attachment screws(9).
• Remove the plug button(13) from the center hole of the cap.(Fig.2) Remove the plug button from the detachable switch housing (Fig.1)
  NOTE: Keep the plug button, shall you choose to remove the light kit fixture in the near future.
  Install spring washer(8) and hex nut(7) onto the threaded nipple(12) from the light kit to secure the switch housing cap(6) or switch housing(1).
  NOTE: Be sure it is secured enough to prevent screws from vibrating loose.

STEP 2. MAKING WIRE CONNECTIONS

• Locate two wires in switch housing, white and blue, labeled “For Light”.
• Connect blue wire from fan(3) to Black wire from Light kit(5), white wire from fan(10) to white wire from Light kit(11) using wire nuts(4).
• After completing wires connection, carefully tuck wires back into fan switch housing.
• Attach the switch housing cap(6) with light kit assembly to fan switch housing(1) with three attachment screws(9) removed from switch housing.
  WARNING: Improper installation could cause the light fixture to fall, or result in electrical shock or personal injury.

STEP 3. INSTALLING GLASS SHADE,WOOD TASSEL

• Raise the glass shade(18) into light fixture pan(14) and secure with three thumb screws(15).
  NOTE: Be sure the glass shade is completely secured to prevent falling when ceiling fan in rotation.

• Attach the provided wood tassel to light kit pull chain(16). Pass the ceiling fan switch chain(2) through another side hole of light fixtue pan, re-attach ceiling fan pull chain(17).

• Installation is complete and you can restore power to ceiling fan and operate.

Replacement – This integrated LED fixture has no bulb to replace.

References

• RP Lighting+Fans - Supplier for electrical distributors & lighting showrooms

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>