Zowill DK09 Smart Lock Installation Guide

Zowill DK09 Smart Lock

Product Information

The device complies with part 15 of the FCC Rules and contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). The device should be installed and operated with a minimum distance of 20cm between the radiator and the user’s body. This equipment complies with radiation exposure limits set forth for an uncontrolled environment in both the United States and Canada.

Product Usage Instructions

Caution: Do not make any changes or modifications to this device that are not explicitly approved by the manufacturer. Doing so could void your authority to operate this equipment.

• Step 1: Install the device with a minimum distance of 20cm between the radiator and your body.
• Step 2: Turn on the device and follow the manufacturer’s instructions for use.
• Step 3: If interference is experienced, try relocating the device to a different location or adjusting its position.
• Step 4: If problems persist, contact the manufacturer for further assistance.

TOOL REQUIRED:
Do not use an electric screwdriver during installation.

INSTALLATION INSTRUCTION

Parts List

If any parts are missing or damaged, please contact Customer Support.

Prepare the door and check dimensions

• A Measure to confirm that the hole in the door is 2-1/8″ (54mm) Measure to confirm that the hole in the door edge is 1″ (25mm).
• B Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70mm)
• C Measure to confirm that the door is 1-3/8″ to 2″ (35mm to 50mm) thick.
• D Make sure the hole in the door frame is drilled a minimum of 1″ (25mm) deep, to leave enough space for the latch to extend into the door frame when the door is locked.

Install the latch and strike

• A Latch backset adjustment
  Backset is the distance from the door edge to the center of the hole in the door. The latch is provided with adjustable C) design which can fit either 2-3/8″(60mm) or 2-3/4″(70mm) backset
  

• B Install the latch

• C Install strike on the door frame.
  IMPORTANT:
  Make sure the hole in door frame is drilled a minimum of 1″ (25mm) deep .

• D Change Handle Direction (Optional)
  Notes: The handle direction can be chan ed for com atible with both right handed and left handed doors.

  • Change the Handle direction of exterior assembly.
    Loosen the reversing screw by using a screwdriver. Rotate the lever to the other end and keep it horizontal. Tighten the reversing screw.

  • Change the Handle direction of interior assembly.
    Loosen the screw completely and remove the screw by using a screwdriver. Rotate the handle to the other side and keep the handle horizontal. Tighten the screw in the Left-hand or Right-hand screw holes according to the actual handle direction.

Install exterior assembly

• A Route the cable below the latch, and insert the torque blade through the slot in the latch.
• B Secure the mounting plate with the supplied screws. Do not overtighten screws.

Install interior assembly

• A Push the battery cover out in the direction as illustrated.
  IMPORTANT: Do not load batteries until lock is completely installed

• B Insert the cable connector to the socket. Push the connector in firmly until it is completely attached.

• C Attach Interior Assembly to Mounting Plate and tighten 3 Screws.

• D Insert 4 AA Alkaline batteries and put on the battery cover.

AT A GLANCE

How to Lock/ Unlock

• UNLOCK the door from outside

• LOCK the door from outside

• UNLOCK the door from inside

• LOCK the door from inside

  • Auto Lock Mode
    In Auto Lock Mode, the lock will automatically move to locked position after 5 seconds, then the lever can’t be turned.

  • Tap and hold Lock icon in App to lock.

Definitions

• Master Code

  • Required for programming user codes, fingerprints and IC card. The default master code needs to be changed before programming.
  • After pairing DDLock App successfully, the master code will be changed to a random 7 digit number, and you can change ii to your own master code in App.

• Auto Lock & One-touch Lock

  • Automatically locks the latch after the door closed in 5 seconds. Auto Lock is disabled by default. The Auto Lock time can be customized between 1 and 900 seconds.
  • One-touch Lock is pressing and holding “#” on the touch keypad for 2 seconds to lock from outside.

• Wrong Entry Limit
  After 5 times unsuccessful attempts at entering an invalid password, the device will shut down for 2 minutes.

• Passage Mode

  • Move the Passage Switch to enable and disable the Passage Mode.
  • Enable Passage Mode, the lock will stay Unlocked until it’s locked manually
  • In Passage Mode, Auto-lock will be disabled.

• Anti-peeping password
  Entering random numbers before or after correct password will also unlock the door, which can prevent the password being exposed.The length of anti-peeping password should be within 16 digits.

Programming Guide

Factory Default Settings

How to Reset?
Press and hold the Reset button on the interior assembly for 5 seconds by using the Reset tool, until you hear a short beep and Green light flashes once.
IMPORTANT· · The App Reset before Buttonresetting. _ must be turned on in DDLock

Settings

Master Code

| Factory Defaut

123456

---|---
Auto Lock| SS
Passage Mode| Off
Reset Button| On
Lock Sound| On
Wrong Code Entry Limit| Slimes
Shutdown Time| 2 minutes

HOW TO REGISTER

Download “DDLock” App in Google Play or App Store.

• STEP 1: Tap on register to get started!
• STEP 2: Fill out this and then tap “Get Code”‘. You will be sent a verification code to verify your account ! Once you receive it, tap on “Register”
  Notes:
  The DDLock app is needed to use this lock. If this lock was professionally installed (or installed by someone other than the homeowner), make sure this step is performed by the homeowner.

Pairing Your Lock

• STEP 1: Tap on the three horizontal lines.
• STEP 2: Tap on “+ Add Lock”. ****
• STEP 3: Tap on “Door Lock ” or “All Locks”.
• STEP 4: Tap on “Next”.
• STEP 5: Tap on the blue plus sign.
  Notes:
  You may need to tap on lock keypad.

Admin Passcode Management

After pairing the lock with DDLock, the admin passcode will be changed to a random 7 digit number, you can check the new admin passcode by following the picture guide below. And you can change it to your own administrator password.

Lock Page Overview

Notes: Some of these icons may not appear if the Gateway is not connected to the lock.

APP Unlock/ Lock

• To unlock the lock, tap this icon once.
• To lock the lock, press and hold on this icon.

Passcode

• STEP 1

  • To access the passcode menu, tap on ” Passcode” icon.
    This will take you to the passcode
    page.
    
    

• STEP 2: Tap on “Generate Passcode”.

• STEP 3: Enter a name for this Passcode.

IC Card

• STEP 1: Tap on “Cards”.
• STEP 2: Tap on “Add Card”.
• STEP 3:
  • Choose the validity period of the lock.
  • Once the lock says “Please swipe your card”, place the card against 5 on the keypad.
  • If you hear a long beep, the card can be used to unlock your lock.

Fingerprints

To add a fingerprint follow these instructions:

• STEP 1: Tap on Fingerprints.
• STEP 2: Tap on “Add Fingerprints”.
• STEP 3
  • Select Fingerprint type depending on when you would like it to be valid.
  • Follow instructions on app. You will be asked to place your finger on the sensor 4 times.

eKeys

• STEP 1: eKeys work by sharing app access of your lock with another DDLock account. eKey recipients will be able to use their phone to unlock/lock the lock.
• STEP 2: Tap on “Send eKey”.
• STEP 3:
  • Enter recipient’s username. It will be the phone number or email address during registration.
  • eKeys do not require wifi or bluetooth to be sent or revoked.

Authorized Admin

Authorized Admins are similar to eKeys; however, an authorized admin can do the following:

• STEP 1:

1. Unlock/lock via the app.
2. Generate, Edit, Delete passcodes, IC cards, & fingerprints.
3. Adjust settings like passage mode, auto-lock timer, & turn on/off the lock sound.

• STEP 2: Tap on “Authorized Admin” Set Timed Admin or Permanent Admin.

Passage Mode & Auto-Lock

• STEP 1: Auto-lock will automatically lock the lock when it has be opened after 5 seconds by default. This can be adjusted with Passage Mode and Auto-lock timer. Outlined below is how to adjust these settings related to auto-lock.
• STEP 2: Select Passage Mode.
• STEP 3: Passage Mode disables auto-lock during a set schedule.

Lock Settings

• Here are some settings you should familiarize yourself with.
• Under Basics, you can view and change information such as Lock Name.
• Gateway shows signal strength if Gateway is connected.
• With Remote Unlock on and a Gateway connected, you can remotely unlock/lock your lock.
• Lock Sound adjusts the locks sound level.
• Import from another lock allows for the transfer of passcodes and cards from one lock to another.
• Delete will remove the lock from your account and clear any settings one the lock. You must be near the lock to do this.

Troubleshooting

• Q: Why the lock won’t accept any inputs after I entered a code or fingerprint incorrectly for so many times?

• A: The lock will shut down for 2 minutes after 5 unsuccessful attempts at entering an invalid code or fingerprint.  You can unlock the lock once in the App or wait 2 minutes to continue.

• Q: How do I lock manually from outside?
  A: Press and hold # to lock the lock from outside.

• Q: The batteries are completely dead before I replace new batteries.
  A: When the batteries are completely dead, the physical keys are available to unlock.

• Q: How do I share access of the lock to my family members?
  A: Go to DDLock App, in eKeys or Authorized Admin, it can share access of the lock to your family.

FCC Statement

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
• CauISED Statementtion: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
  • This device may not cause harmful interference,
  • this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

ISED Statement

• This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
  • This device may not cause interference.
  • This device must accept any interference, including interference that may cause undesired operation of the device.
• The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B).
• This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
• This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
• This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Information & Safety Warnings

• Protect your User Codes and Master Code.
• Restrict access to your lock’s interior assembly and routinely check your settings to ensure they have not been altered without your knowledge.
• Do not use an electric screwdriver during installation.
• This manufacturer advises that no lock can provide complete security by itself.
• This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property.
• No lock can substitute for caution, awareness of your environment, and common sense.
• Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.
• The lock is water resistant. It can withstand water splashes; however, do not let water and liquids get into the lock.
• Avoid exposure to direct sunlight. Long-term exposure to direct sunlight may damage the lock.

The Video of Installation and Programming Guide

Website: www.zowill.com
Service: support@zowill.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>