HiKOKI M12VE HP Variable Speed Plunge Router Instruction Manual

M 12VE
Instruction Manual

**

Handling instructions**

|
---|---

**GENERAL POWER TOOL SAFETY WARNINGS

**

**WARNING
** Read all safety warnings, instructions, illustrations, and specifi cations provided with this power tool.
Failure to follow all instructions listed below may result in electric shock, fi re, and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1. Work area safety
   a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
   b) Do not operate power tools in explosive atmospheres, such as in the presence of fl flammable liquids, gases, or dust. Power tools create sparks that may ignite dust or fumes.
   c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2. Electrical safety
   a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodifi end plugs and matching outlets will reduce the risk of electric shock.
   b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
   c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
   d) Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep the cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
   e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock.
   f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. The use of an RCD reduces the risk of electric shock.

3. Personal safety
   a) Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the infl uence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
   b) Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions will reduce personal injuries.
   c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your fi nger on the switch or energizing power tools that have the switch on invites accidents.
   d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
   e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
   f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
   g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of dust collection can reduce dust-related hazards.
   h) Do not let familiarity gained from the frequent use of tools allow you to become complacent and ignore tool safety principles.
   A careless action can cause severe injury within a fraction of a second.

4. Power tool use and care
   a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
   b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
   c) Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
   d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
   Power tools are dangerous in the hands of untrained users.
   e) Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may aff ect the power tool operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
   f) Keep cutting tools sharp and clean.
   Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
   g) Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations diff erent from those intended could result in a hazardous situation.
   h) Keep handles and grasping surfaces dry, clean, and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

5. Service
   a) Have your power tool serviced by a quality ed repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

PRECAUTION
Keep children and infi rm persons away. When not in use, tools should be stored out of reach of children and infi rm persons.

ROUTER SAFETY WARNINGS

1. Hold the power tool by insulated gripping surfaces only, because the cutter may contact its own cord. Cutting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
2. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by your hand or against the body leaves it unstable and may lead to loss of control.
3. Single-hand operation is unstable and dangerous. Ensure that both handles are gripped fi only during operation. (Fig. 18)
4. The bit is very hot immediately after the operation. Avoid bare hand contact with the bit for any reason.
5. Use bits of the correct shank diameter suitable for the speed of the tool.

DESCRIPTION OF NUMBERED ITEMS (Fig. 1–Fig. 18)

SYMBOLS

WARNING
The following show symbols used for the machine. Be sure that you understand their meaning before use.

| M12VE: Router
---|---
| To reduce the risk of injury, users must read the instruction manual.
| Always wear eye protection.
**| Always wear hearing protection.
| Only EU countries Do not dispose of electric tools together with household waste material! In observance of European Directive 2012/19/EU on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
| Disconnect the mains plug from the electrical outlet
**| Class II tool

STANDARD ACCESSORIES

1. Parallel Guide ……………………………………………………..1
2. Template Guide …………………………………………………..1
3. Wrench ………………………………………………………………1
4. Wing Bolt (A) ………………………………………………………2
5. Lock Spring ………………………………………………………..2
6. Dust Collector Set ………………………………………………..1

Standard accessories are subject to change without notice.

SPECIFICATIONS

Weight (without cord and
standard accessories)| 5.4 kg

• Be sure to check the nameplate on the product as it is subject to change by area.
  NOTE
  Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to change without prior notice.

PRIOR TO OPERATION

1. Power source
   Ensure that the power source to be utilized conforms to the power requirements specifi ed on the product nameplate.

2. Power switch
   Ensure that the power switch is in the OFF position. If the plug is connected to a receptacle while the power switch is in the ON position, the power tool will start operating
   immediately, which could cause a serious accident.

3. Extension cord
   When the work area is removed from the power source, use an extension cord of suffi client thickness and rated capacity. The extension cord should be kept as short as
   practicable.

4. Setting the attachment angle of the handle
   As Fig. 1 shows, the handle attachment angle can be set in three stages. Use a plus head screwdriver to loosen the machine screw attached to the handle, adjust the handle to the desired position and retighten the machine screw.

5. RCD
   The use of a residual current device with a rated residual current of 30 mA or less at all times is recommended.

INSTALLING AND REMOVING BITS

WARNING

Be sure to switch the power OFF and disconnect the plug from the receptacle to avoid serious trouble.

1. Installing bits
   (1) Clean and insert the shank of bit into the collet chuck until the shank bottoms, then back it out approximately 2 mm.
   (2) With the bit inserted and pressing the lock pin holding the armature shaft, use the 23 mm wrench to fi firmly tighten the collet chunk in a clockwise direction (viewed from under the router). (Fig. 2)
   CAUTION
   ○ Ensure that the collet chuck is fi only tightened after inserting a bit. Failure to do so will result in damage to the collet chuck.
   ○ Ensure that the lock pin is not inserted into the armature shaft after tightening the collet chuck. Failure to do so will result in damage to the collet chuck, lock pin, and armature shaft.
   (3) When using the 8 mm or 1/4″ diameter shank bit, replace the equipped collet chuck with the one for the 8 mm or 1/4″ diameter shank bit which is provided as the optional accessory.

2. Removing Bits
   When removing the bits, do so by following the steps for installing bits in reverse order. (Fig. 3)

CAUTION
Ensure that the lock pin is not inserted into the armature shaft after tightening the collet chuck. Failure to do so will result in damage to the collet chuck, lock pin, and armature shaft.

HOW TO USE THE ROUTER

1. Adjusting the depth of cut (Fig. 4)
   (1) Use a stopper pole to adjust the depth of the cut.
   (1) Place the tool on a fl at the wood surface.
   (2) Turn the stopper block so that section to which the cutting depth setting screw on a stopper block is not attached comes to the bottom of the stopper pole. Loosen wing olt allowing the stopper pole to contact with the stopper block.
   (3) Loosen the lock lever and press the tool body until the bit just touches the fl at the surface. Tighten the lock lever at this point. (Fig. 5)
   (4) Tighten wing bolt. Align the depth indicator with the “0” graduation of scale.
   (5) Loosen wing bolt, and raise until indicator aligns with the graduation representing the desired cutting depth. Tighten the wing bolt.
   (6) Loosen the lock lever and press the tool body down until the stopper block obtains the desired cutting depth.

2. As shown in Fig. 6 (a), loosening the two nuts on the threaded column and moving them down will allow you to move down to the end position of the bit when the lock
   lever is loosened. This is helpful when moving the router to align the bit with the cutting position. As shown in Fig. 6 (b), tighten the upper and lower nuts to secure the cutting depth.
   (3) When you are not using the scale to set the cutting depth, push up the stopper pole so that it is not in the way.

2. Stopper block (Fig. 7)
   The 2 cut-depth setting screws attached to the stopper block can be adjusted to simultaneously set 3 diff erent cutting depth. Use a wrench to tighten the nuts so that the
   cut-depth setting screws do not come loose at this time.

3. Guiding the router
   WARNING
   Be sure to switch the power OFF and disconnect the plug from the receptacle to avoid serious trouble.
   (1) Template Guide
   Use the template guide when employing a template for producing a large quantity of identifi cally shaped products.
   As shown in Fig. 8, secure the template guide to the base of the router with two accessory screws. At this time, ensure that the projection side of the template guide is facing the bottom surface of the base of the router.
   A template is a profi ling mold made of plywood or thin lumber.
   When making a template, pay particular attention to the matters described below and illustrated in Fig. 9. When using the router along the interior plane of the template, the dimensions of the fi finished product will be less than the dimensions of the template by an amount equal to dimension “A”, the diff erence between the radius of the template guide and the radius of the bit. The reverse is true when using the router along the exterior of the template.
   Secure the template to the workpiece. Feed the router in the manner that the template guide moves along the template as shown in Fig. 10.
   (2) Parallel guide (Fig. 11)
   Use the parallel guide for chamfering and groove cutting along the materials side.
   Insert the guide bar into the hole in the base, adjust the distance between the bit and the guide surface, and then fi firmly tighten the wing bolt (A).
   As shown in Fig. 12, securely attach the bottom of the base to the processed surface of the materials. Feed the router while keeping the guide plane on the surface of the materials.

4. Adjusting the rotation speed
   The M12VE has an electronic control system that allows stepless rpm changes.
   As shown in Fig. 13, dial position “1” is for minimum speed, and position “6” is for maximum speed.

5. Cutting
   CAUTION
   Wear eye protection when operating this tool.
   Keep your hands, face, and other body parts away from the bits and any other rotating parts, while operating the tool.
   1 As shown in Fig. 14, remove the bit from the workpieces and press the switch lever up to the ON position. Do not start cutting operation until the bit has reached full rotating speed.
   2 The bit rotates clockwise (arrow direction indicated on the base). To obtain maximum cutting eff ectiveness, feed the router in conformance with the feed directions shown in Fig. 15.
   NOTE If a worn bit is used to make deep grooves, a high-pitched cutting noise may be produced. Replacing the worn bit with a new one will eliminate the high-pitched noise.

6. Dust Collector Set Connect the dust collector set cleaner to collect dust.
   (1) Mounting the dust collector Use a screwdriver to attach the two screws to the base. (Fig. 16) Align the holes on the dust collector with the two screws and attach the dust collector. Tighten the two knob nuts. Connect the cleaner to the dust collector. (Fig. 17)
   (2) Dismounting the dust collector Use a screwdriver to loosen the two screws.

MAINTENANCE AND INSPECTION

1. Oiling To ensure smooth vertical movement of the router, occasionally apply a few drops of machine oil to the sliding portions of the columns and end bracket.
2. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazards.
3. Maintenance of the motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water.
4. Inspecting the carbon brushes For your continued safety and electrical shock protection, carbon brush inspection and replacement on this tool should ONLY be performed by a HiKOKI AUTHORIZED SERVICE CENTER.
5. Replacing supply cord If the supply cord of the Tool is damaged, the Tool must be returned to HiKOKI Authorized Service Center for the cord to be replaced.

CAUTION
In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.

SELECTING ACCESSORIES

The accessories of this machine are listed on page 92. For details regarding each bit type, please contact the HiKOKI Authorized Service Center.
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with statutory/country specifi c regulation. This guarantee does not cover defects or damage due to misuse, abuse, or normal wear and tear. In case of a complaint, please send the Power Tool, undismantled, with the GUARANTEE CERTIFICATE found at the end of this Handling instruction, to a HiKOKI Authorized Service Center.
IMPORTANT
Correct connection of the plug The wires of the main lead are colored in accordance with the following code:
Blue: — Neutral
Brown: — Live
As the colors of the wires in the main lead of this tool may not correspond with the colored markings identifying the terminals in your plug proceed as follows: The wire colored blue must be connected to the terminal marked with the letter N or colored black. The wire colored brown must be connected to the terminal marked with the letter L or colored red. Neither core must be connected to the earth terminal.
NOTE: This requirement is provided according to BRITISH STANDARD 2769: 1984.
Therefore, the letter code and color code may not be applicable to other markets except The United Kingdom.
Information concerning airborne noise and vibration
The measured values were determined according to
EN62841 and declared in accordance with ISO 4871.
Measured A-weighted sound power level: 94 dB (A)
Measured A-weighted sound pressure level: 83 dB (A)
Uncertainty K: 3 dB (A).
Wear hearing protection.
Vibration total values (triax vector sum) are determined according to EN62841.
Cutting MDF:
Vibration emission value ah = 8.9 m/s2
Uncertainty K = 3.4 m/s2
The declared vibration total value and the declared noise emission value have been measured in accordance with a standard test method and may be used for comparing one tool with another.
They may also be used in a preliminary assessment of exposure.
WARNING

• The vibration and noise emission during actual use of the power tool can diff er from the declared total value depending on the ways in which the tool is used especially what kind of workpiece is processed; and
• Identify safety measures to protect the operator that is based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

NOTE
Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to change without prior notice.
EC DECLARATION OF CONFORMITY
We declare under our sole responsibility that Router, identifi ed by type and specifi c identifi cation code 1), is in conformity with all relevant requirements of the directives 2) and standards 3). Technical fi le at 4) – See below.
The European Standard Manager at the representative offi ce in Europe is authorized to compile the technical fi le.
The declaration is applicable to the product affi xed CE marking.
1) M12VE
C340086R C340085M
2) 2006/42/EC, 2014/30/EU, 2011/65/EU
*3) EN62841-1:2015
EN62841-2-17:2017
EN55014-1:2006+A1:2009+A2:2011
EN55014-2:1997+A1:2001+A2:2008
EN61000-3-2:2014
EN61000-3-3:2013

• 4) Representative offi ce in Europe
  Hikoki Power Tools Deutschland GmbH
  Siemensring 34, 47877 Willich, Germany
  Head offi ce in Japan
  Koki Holdings Co., Ltd.
  Shinagawa Intercity Tower A, 15-1, Konan 2-chome,
  Minato-ku, Tokyo, Japan
  30. 8. 2021
  Akihisa Yahagi
  European Standard Manager
  A. Nakagawa
  Corporate Offi cer
  Koki Holdings Co., Ltd.
  108
  Code No. C99740191 M
  Printed in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>