ADLER AD 7742 Ceramic Fan Heater User Manual
- June 10, 2024
- ADLER
Table of Contents
AD 7742 Ceramic Fan Heater
Product Information
The AD 7742 is a heating unit with a nominal heat output of 1.5 kW and a minimum heat output of 0.8 kW. It has a maximum continuous heat output of 1.5 kW and an auxiliary electricity consumption of 0.000 kW in standby mode. The unit comes with different options for heat output and room temperature control, including manual heat charge control with integrated thermostat and electronic heat charge control with room and/or outdoor temperature feedback.
Contact Information
For any questions or concerns, please contact Adler Sp. z o.o. at ul. Ordona 2A, 01-237 Warszawa, Polska.
Product Usage Instructions
- Ensure that the unit is not covered with clothes, blankets, or other textiles that may cause ignition.
- Choose the desired type of heat output and room temperature control from the available options.
- If using the unit with a black bulb sensor or working time limitation, make sure to follow the manufacturer’s instructions for proper usage.
- If using the unit with mechanic thermostat room temperature control or electronic room temperature control plus day/week timer, set the desired temperature and timer settings.
- If using the unit with other control options such as presence detection or open window detection, make sure to follow the manufacturer’s instructions for proper usage.
- To turn on the unit, adjust the heat output and temperature settings as desired.
- To turn off the unit, adjust the heat output to the minimum setting and unplug the unit from the power source.
Model
Model| AD7742| | |
---|---|---|---|---
Item| Symbol| Value| Unit| | Item| Unit
Heat output
| | | Type of heat input, for electric storage local space heaters only
(select one)
Nominal heat output|
P nom
|
1,5
|
kW
| | manual heat charge control, with integrated thermostat|
[no]
Minimum heat output (indicative)|
P min
|
0,8
|
kW
| | manual heat charge control with room and /oroutdoor temperature
feedback| [no]
Maximum continuous heat output|
Pmax,c
|
1,5
|
kW
| | electronic heat charge control with room and /or outdoor temperature
feedback| [no]
Auxiliary electricity consumption| | | | |
fan assisted heat output
| [no]
At nominal heat output|
el max
|
0,000
|
kW
| | Type of heat output/room temperature control (select one)
At minimum heat output|
el min
|
0,000
|
kW
| | single stage heat output and no room temperature control| [no]
In standby mode|
el SB
|
0,000
|
kW
| | two or more manual stages, no room temperature control| [no]
| | | with mechanic thermostat room temperature control| [yes]
| | | with electronic room temperature control| [no]
| | | electronic room temperature control plus day timer| [no]
| | | electronic room temperature control plus week timer| [no]
| | | Other control options (multiple selections possible)
| | | room temperature control, with presence detection| [no]
| | | room temperature control, with open window detection| [no]
| | | with distance control option| [no]
| | | with adaptive start control| [no]
| | | with working time limitation| [yes]
| | | with black bulb sensor| [yes]
Contact| Adler Sp. z o.o. ul. Ordona 2A, 01-237 Warszawa, Polska
This product is suitable only for occasional use or for use in well insulated rooms.
WARNING
DO NOT COVER« INSCRIPTION IMPORTANCE The inscription on the device means that the device is not to be covered with clothing, blankets and other textile products which could cause ignition.
SAFETY CONDITIONS IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE READ
CAREFULLY AND KEEP FOR FUTURE REFERENCE
The warranty conditions are different, if the device is used for commercial
purpose.
-
Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
-
The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
-
The applicable voltage is 220-240V, ~50Hz. For safety reasons it is not appropriate to connect multiple devices to one power outlet.
-
Please be cautious when using around children. Do not let the children to play with the product. Do not let children or people who do not know the device to use it without supervision.
-
WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children, unless they are over 8 years of age and these activities are carried out under supervision.
-
After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
-
Never put the power cable, the plug or the whole device into the water. Never expose the product to the atmospheric conditions such as direct sun light or rain, etc.. Never use the product in humid conditions.
-
Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
-
Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defected product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
-
Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
-
Never use the product close to combustibles.
-
Do not let cord hang over edge of counter or touch hot surfaces.
-
Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.
-
In order to provide additional protection, it is recommended to install residue current device (RCD) in the power circuit, with residual current rating not more than 30 mA. Contact professional electrician in this matter.
-
Never use this device close to water, e.g.: Under shower, in bathtube,
or above sink filled with water. -
If using the device in bathroom after use remove the power plug from the socket, because water proximity presents risk, even if the device is turned off.
-
Do not allow the device or power adaptor to wet. If the device falls into water, immediately remove the power plug or power adaptor from the socket. If the device is powered, do not put hands in the water. Have the device checked by the qualified electrician before using it again.
-
Do not touch the device or power adaptor with wet hands.
-
Place the fan heater only on flat, stable surface
-
Always turn the fan heater off and set the thermostat dial to minimum before removin the power plug from the socket.
-
Never use the fan heater in high humidity rooms – bathroom, shower room, swimming pools etc. The humidity can cause short circuit, and effect in damaging the device.
-
The operating fan heater needs to be under supervision and in sight all the time. If you are leaving the room with the fan heater, always turn the fan heater off. If the fan heater is not used, the power plug has to be removed from the power outlet.
-
Do not connect the fan heater to the automatic switching device, for example temperature controlling device or time switch.
-
Flammable materials, for example furniture, bedclothes, paper, clothes, curtains should be kept at least one meter from the fan heater.
-
Do not cover the device or put any objects on it while it is operating. Do not use the device to dry clothes.
-
The power cord should not be placed above the fan heater, and it should not touch or be placed near hot surfaces of the fan heater. Do not place the fan heater directly under the power outlet.
-
The heating surfaces can heat to a temperature of 60 °C or higher. The fan heater should be in a place that children and animals do not have access to.
-
The device is not intended to be installed or used in vehicles.
-
Some parts inside the device can be hot or cause sparking. Do not use the fan heater in places, where gasoline, paints or other flammable materials are used or stored.
-
Do not use this heater in the immediate vicinity of a bathtub, shower or swimming pool
-
Do not use this heater if it has been dropped
-
Do not use if there are visible signs of damage to the heater.
-
Use the heater on a level and stable surface or attach it to the wall, if provided for by the manufacturer
WARNING: Do not use this heater in small rooms where there are people who are unable to leave them by themselves, unless constant supervision is ensured. WARNING: To reduce the risk of fire, keep textiles, curtains or other flammable materials at least 1 m away from the heater air outlet.
DESCRIPTION OF THE DEVICE
CERAMIC FAN HEAER AD7742
- Thermostat dial
- Power switch / heating level control
- (a) – cold airflow
- (b) – 750W
- (c) – 1500W
- Control lamp
USING THE DEVICE
Place the device on flat surface, leave safe area between the device and other objects from the front 120cm and from the other sides of the device 50cm. Plug in the device.
- The heater has two levels of heating power and fan mode.
- Position (0) – device is switched off
- Position (a) – unheated air flow
- Position (b) – 750W warm air flow
- Position (c) – 1500W hot air flow
- On both heating levels the temperature can be adjusted using thermostat dial (1).
- First, turn the power switch (1) into desired position (a, b, c).
Then, turn the thermostat dial (1) to the desired temperature position between MIN and MAX. When you feel the room temperature is comfortable, turn the thermostat dial (1) anti-clockwise slowly until the device switches off, but not more. The thermostat switch will keep the room temperature at the desired temperature automatically.
The device is protected against the overheating by the means of a thermal switch, which can power it off for a while. If this happens, unplug the device and wait 5-10 minutes to let the device cool down. After a while you can continue to use the device. This device is also equipped with a safety tip- over switch which automatically turns the device off if the it leans or falls. The heater will resume back to normal when it is returned to the upright position.
CLEANING AND MAINTENANCE
Make sure the device is not hot. Before cleaning the device remove the plug from the electrical socket. Keep the air inlet and outlet openings clean. Do not allow dust to collect on the openings. Clean the housing using only dry or moist cloth. Do not immerse the device in water.
TECHNICAL DATA
- Power: 1500W
- Voltage: 220-240V ~50-60Hz
To protect your environment:
please separate carton boxes and plastic bags and dispose them in corresponding waste bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may effect the environment. Do not dispose this appliance in the common waste bin.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>