aosu C9E2CA11 Solar Powered Wireless Security Camera User Guide
- June 1, 2024
- aosu
Table of Contents
Solar-Powered Wireless Security Camera
SolarCam D1 SE
Quick Start Guide
C9E2CA11 Solar Powered Wireless Security Camera
AOSUCare
Hi Customer
Thank you for choosing AOSU security products. We have always put our
customers first and foremost.
There are 3 things you should know before using this product:
-
Micro SD Card
Ifyou don’t have a Micro SD Card available at home now and don’t want to spend extra time choosing one, please contact us directly.
TIP: the Micro SD Card gotta be formated after inserting it up. -
Select 2.4G Wi-Fi
The product only supports 2.4G Wi-Fi, please select 2.4G Wi-Fi when setting up the app. -
Select installation location.
Please use your mobile phone to test the coverage of the home WiFi signal at the planned installation position before installation, S0 that the product can receive a better signal
Get all the tutorial videos of using product including but no limit to set up the app, installation and format micro sd card, visit: aosulife.com
Join “AOSUCare” today as three ways below to get all of your problems solved by one-on-one live chat and phone service tech support,
What’s Included
SolarCam D1 SE
Solar Panel
Product overview
CAUTION: Please insert the Micro SD Card according to the direction shown
in the diagram. Micro SD Card might JAM if inserted incorrectly and device
could be damaged.
Micro SD Card Port: Support Micro SD Card for local storage (Max 128G8) Reset
button: Press and hold the button for 3 seconds, and then the device will be
ready to be connected.
Card capacity requirements: 8-128GB;
Read and wite speed requirements: class10 level File format: FAT32.
Setting Up the System
Download the Aosu App from the App Store (iOS devices) or Google Play (Android devices).
https://static.aosulife.com/download.html?src=box&model=C9E
Sign up for an Aosu App account, then follow the onscreen instructions to complete the setup.
Mounting the Camera
Find a Good Mounting Spot
To find a spot to mount Camera, you need to test wireless Signal strength.
- Open the Aosu App, go to Camera Settings > Mounting Guide.
- To test the wireless signal strength, take your camera and phone to the location where you want to mount the camera.
- Move the camera as close to the Wi-Fi Router as possible to get a better signal.
Select Height and location
Hang Camera 2-3meters above the ground. This height maximizes the detection
range of the motion sensor of Camera. Avoid placing Camera under direct
sunlight.
Installation instruction of solar panel
- keep the installation angle of solar panels about 30-45° with the horizontal plane, as shown in the picture below.
- The installation between the solar panel and the camera is shown in the following figure (open up the silicone cover at the bottom of the camera, remove the small center part of the cover, insert the power cord through the opening and plug it into the USB-C Port and then close the cover taking up any slackn the power cord from the solar panel).
Tips for the installation of solar panel
- When installing in the northern hemisphere, face the panel to the south, and when installing in the southern hemisphere, face the panel to the north.
- Take care toinstall the solar panel so that the sun is not blocked by any items such as eaves, trees branches, etc.
Test the Wi-Fi signal at installation position
Use cell phone to test Wi-Fi signal quality at the installation position
before installing camera, make sure the Wi-Fi router can provide good Wi-Fi
signal.
Installation
- Drilling according to position sticker, drill bit: 15/64″(6 mm)
- Insert the plugs.
- Tighten the screws
What is required:
Installation instruction of solar panel
Place Solar Panel in an area with consistent sunlight through-out the year.It
only needs a few hours of direct sunlight each day to keep your camera
powered.
The amuont of energy that the solar panel produces is affected by weather
conditions,seasonal changes, geographic loction,etc,
-
Fix the base to your mounting location using the included screws.If the installation surface is soft or unstable first use a φ 6.0 drill bit to drill a hole in the wall,then insert the anchor nail into the hole,and fix thebase with screws.
-
First install the locking screw cap into the universal joint and then screw the circular socket nut into the universal joint.
-
Screw the universal joint into the back of the solar panel.Tighten it firmly with the attached nut.
-
Screw the locking screw cap into the base.Make sure that the universal joint is angled upward.
-
When adjusting the solar panel left or right,loosen thelocking screw cap,turn the sleeve rod,and tighten thelocking screw cap when the panel is in position.
-
Solar panel’s angle can be adjusted up and down up to 90°.
Tip: After the installation is complete,please check that all locking mechanisms are tightly secured
Notice
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment. Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures: (1)
Reorient or relocate the receiving antenna. (2) Increase the separation
between the equipment and receiver. (3) Connect the equipment into an outlet
on a circuit different from that to which the receiver is connected. (4)
Consult the dealer or an experienced radio/ TV technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements.
The device can be used in fixed/mobile exposure condition.
The min separation distance is 20cm.
IC Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions: (1)This device
may not cause interference (2)This device must accept any interference,
including interference that may cause undesired operation of the device
IC RF Statement:
This equipment complies with IC RSS – 102 radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator and your body.
**** This product complies with the radio interference requirements of the
European Community.
Declaration of Conformity
Hereby, Aosu declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU.
For the declaration of conformity, visit the Web
site:https://www.aosulife.com.
This product can be used across EU member states Do not use the Device in the
environment at too high or too low temperature, never expose the Device under
strong sunshine or too wet environment.
The suitable temperature for Camera and accessories is -10°C—50°C.
RF exposure information: The Maximum Permissible Exposure (MPE) level has been
calculated based on a distance of d=20 cm between the device and the human
body. To maintain compliance with RF exposure requirement, use product that
maintain a 20cm distance between the device and human body.
For Camera : Wi-Fi Operating Frequency Range: 2412~2472MHz ; Wi-Fi Max Output
Power: 17.13dBm(EIRP)
This product is designed and manufactured with high quality materials
and components, which can be recycled and reused.
This symbol means the product must not be discarded as household waste,
and should be delivered to an appropriate collection facility for recycling.
Proper disposal and recycling helps protect natural resources, human health
and the environment. For more information on disposal and recycling of this
product, contact your local municipality, disposal service, or the shop where
you bought this product.
Customer Service
Warranty
12-month limited warranty(The actual warranty period shall be implemented
according to the requirements of local laws and regulations)
Email Us
Customer Support: support@aosulife.com
CallUs
United States: +1-866-905-9950 Mon-Fri
9AM-5PM(PST)
United Kingdom: +44-20-3885-0830 Mon-Fri 9AM-5PM(GMT)
Germany: +49-32-221094692 Mon-Fri 9AM-5PM(CET)
Japan: +81-50-5840-2601 Mon-Fri 9AM-5PM (JST )
support@aosulife.com www.aosulife.com @aosulife
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>