BenQ VS20T InstaShow S Wireless Presentation Device User Guide

VS20T InstaShow S Wireless Presentation Device
User Guide

Regulatory Statements

Note: Not all models are available in all regions. If certain safety regulations are required for specific region, BenQ ensures that products available in that region are complied with the requested regulations.

Battery caution

• Do not put the remote control in the direct heat, humidity & Avoid fire.
• Do not drop the remote control.
• Do not expose the remote control to water or moisture, this could result in malfunction.
• Confirm there is no object between the remote control and the remote sensor of the product.
• When the remote control will not be used for an extended period, remove the batteries.

Battery safety notice

The use of the wrong type of batteries may cause chemical leaks or explosion.
Please note the following:

• Always ensure that the batteries are inserted with the positive and negative terminals in the correct direction as shown in the battery compartment.
• Different types of batteries have different characteristics.
• Do not mix different mix old and new batteries. Mixing old and new batteries will shorten battery life or cause chemical leaks from the old batteries.
• When batteries fail to function, replace them immediately.
• Chemicals which leak from batteries may cause skin irritation. If any chemical matter seeps out of the batteries, wipe it up immediately using a dry cloth, and replace the batteries as soon as possible.
• Due to varying storage conditions, the battery life for the batteries included with your product may be shortened. Replace them within 3 months or as soon as you can after initial use.
• There may be local restrictions on the disposal or recycling of batteries. Consult your local regulations or waste disposal provider.

CE DOC
DECLARATION OF CONFORMITY
The device complies with the requirements set out in the Council Directives relevant Union harmonisation legislation:

• RED Directive (2014/53/EU)
• RoHS Directive 2011/65/EU & (EU) 2015/863
• Ecodesign Directive 2009/125/EC
• Turkish ErP (Decision 2010/643)
• Turkish EEE Directive

For EU
Hereby, BenQ Corporation, declares that this VS20 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The full test of the EU declaration of conformity is available at the following internet address: https://www.benq.eu/en-eu/index.html
This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Hardware Version (certified version):
VS2OR: A5BM-013520G05
VS2OT: A5BM-013720005, A5BM-013820004
Software Version (certified version): VS2OR: VS20(R)1.00.00
VS2OT: VS20(T)_1.00.00
Frequency band: 2.4G

| VS2OR
---|---
RF Output Power| 19.06 dBm

Frequency Band: 5G

| | VS2OT| VS2OR
---|---|---|---
RF Output Power| 5.18-5.24G| 22.46 dBm| 22.16 dBm
5.26-5.32G| 21.21 dBm| 21.96 dBm
5.50-5.70G| 22.43 dBm| 28.43 dBm

The WLAN function for this device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range.

| AT| BE| BG| HR| CY| CZ| DK
---|---|---|---|---|---|---|---
EE| Fl| FR| DE| EL| HU| IE
IT| LV| LT| LU| MT| NL| PL
PT| RO| SK| SI| ES| SE| UK
| UK
---|---

SAR information for radio equipment in France

2020-03-18 Guide Reglementation DAS Vf Decree 2019-1186 of 15 November 2019 relating to the display of the specific absorption rate of radioelectric equipment.
VS20T: This product complies with EU requirements regarding restriction of exposure of persons to radio-frequency energy (RF) emitted by telecommunication and radio devices as it is designed and manufactured in such a way as not to exceed the exposure limits indicated by the European Union Commission.
The permitted SAR limit for the general population is 2.0 W/Kg.
This limit guarantees an ample safety margin that protects all persons regardless of age and health condition
The measured SAR value is 0.605 W/kg
VS20R: The minimum distance between the user and/or any bystander and the radiating structure of the transmitter is 15 cm.

WEEE

WEEE directive Disposal of Waste Electrical and Electronic Equipment and/or Battery by users in private households in the European Union.
This symbol on the product or on the packaging indicates that this can not be disposed of as household waste. You must dispose of your waste equipment and/ or battery by handling it over to the applicable take-back scheme for the recycling of electrical and electronic equipment and/or battery. For more information about recycling of this equipment and/or battery, please contact your city office, the shop where you purchased the equipment or your household waste disposal service. The recycling of materials will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and environment.
Recycling information: See https://www.beng.com/en-us/support/recycling /global-recycle.html for details.

EU REACH SVHC Disclosure on Candidate List
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals, EC 1907/2006) is the European Union’s (EU) chemical substances regulatory framework. REACH requires BenQ Corporation to provide customers with sufficient information on Substances of Very High Concern (SVHC) contained in products in concentration above 0.1% weight by weight (w/w) to allow safe use of the product.
RoHS Statement
This product is compliant to implemented RoHS (Restriction of Hazardous Substances) type regulations worldwide, including but not limited to China, India, Japan, Korea and European Union.
EU RoHS

*: PCBA consisted of bare printed circuit board, soldering and its surface-mounted elements, such as resistors, capacitors, arrays, connectors, chips, etc.
NOTE 1: The “0” indicates that the percentage content of the substance to be calculated is not exceeding the reference percentage content of EU RoHS directive (2011/65/EU & EU 2015/863).
NOTE 2: T he “exempted” item means that the specified chemical substance corresponds to the items exempted by the EU RoHS directive (2011/65/EU & EU 2015/863).
India RoHS
Restriction on Hazardous Substances statement (India)
This product complies with the “India” E-waste Rule 2016″ and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or PolyBrominated Diphenyl Ethers in concentrations exceeding 0.1 weight% and 0.01 weight for cadmium except for exemptions set in Schedule 2 of the Rule.

For UK only

• The mains lead (power cable) on the equipment comes with a moulded plug incorporating a fuse.
• The rating of the fuse is indicated on the pin face of the plug and, if it requires replacing, a fuse approved by ASTA or BSI to BS 1362 of the same rating must be used.
• If the plug has a detachable fuse cover, remember to place the fuse cover back if you need-to change the fuse.

DO NOT use a plug without the fuse cover. If the fuse cover is missing, contact your nearest BenQ Customer Service Center for assistance.

UKCA Declaration of Conformity

The object of the declaration described above is in conformity with the relevant UK harmonisation legislation*

• Radio Equipment Regulations 2017
• The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2019
• The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012
• UKCA Marking (for UK market except Northern Ireland)

FCC statement (for the United States only)

Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used fin accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Conned the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/7V technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC RF exposure information (SAR)
Radiation Exposure Statement

Model Name: VS2OT
FCC ID: JVP
This device meets the government’s requirements for exposure VS20T to radio waves. This device is designed and manufactured not to  exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the OJT transmitting at the specified power level in different channels. The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/eot/ea/fccid after searching on FCC ID: JVPVS20T
Model Name: VS2OR
FCC ID: JVPVS2OR
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
FCC SDoC:
Visit www.benq.com.en-us > Support > the purchased model > the User Manual tab to access the SDoC Supplier’s Declaration of Conformity) document. You may not find your product’s DoC document online as it was not required at the time the product was manufactured. However, it does not change the fact that the product has been tested to comply with FCC standards, as indicated by the FCC logo on the product or on the label.
FCC SAR
This equipment should be installed and operated with minimum distance 5mm between the radiator & your body.
SAR compliance has been established in typical laptop computer(s) with USB slot, and product could be used in typical laptop computer with USB slot. Other application like handheld PC or similar device has not been verified and may not compliance with related RF exposure rule and such use shall be prohibited.
The USB dongle transmitter is approved for use in typical laptop computers. To comply with FCC RF exposure requirements, it should not be used in other devices or certain laptop and tablet computer configurations where the USB connectors on the host computer are unable to provide or ensure the necessary operating configurations intended for the device and its users or bystanders to satisfy RF exposure compliance requirements.
IC statement (for Canadian users)
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Indoor use
This device is for indoor use only when operated in the frequency band 5150 —525:, MHz
Important note:

Radiation Exposure Statement

 Model Name:
IC: 6175A-VS2OT | Radio Frequency (RF) Exposure Information VS2OT The radiated output power of the Wireless Device is below the Innovation, Science and Economic Development Canada radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized.
This device has been evaluated for and shown compliant with the IC Specific Absorption Rate (-SAW) limits when operated in portable exposure conditions.
Model Name: VS2OR IC: 6175A-VS20R| Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Innovation, Science and Economic Development Canada radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized.
This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a person’s body).

This radio transmi ter (IC: 6175A-VS20T) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited foruse with this device.

The device for operation in the band 5150-5250MHz is only for indoor use.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate
Exposure of humans to RF fields (RSS-1 02)
The computers employ low gain integral antennas that do not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6,obtainable from Health Canada’s Web site at http://www.hc-sc.ge.ca/
The radiated energy from the antennas connected to the wireless adapters conforms to the IC limit of the RF exposure requirement regarding IC RSS-102, Issue 9 clause 4. SAR tests are conducted using recommended operating positions accepted by the FCC/ RSS with the device transmitting at its highest certified power level in all tested frequency band without distance attaching away from the body.
Non-compliance with the above restrictions may result in violation of FCC RF exposure guidelines.
RF Exposure Information
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with 20cm between
the radiator & your body.
This device complies with ICES-003 (B)/NMB-003(B). This Class B device meets all the requirements of the Canadian interference-causing equipment regulations.

© 2023 BenQ Corporation.
All rights reserved.
Rights of modification reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>