elk Home 82164-1 6.5 Inch Wide 1-Light Mini Pendant Instruction Manual
- June 10, 2024
- elk HOME
Table of Contents
82164-1 6.5 Inch Wide 1-Light Mini Pendant
Product Information
The product is a light fixture that requires installation in accordance with the National Electrical Code (NEC) and all local code specifications. The package includes a mounting bracket, junction box screws, a screw collar loop, a ground screw, wire nuts, and fixture wires. The fixture requires at least one 6-inch system to be used during installation.
Product Usage Instructions
- Before starting installation, disconnect power at the main fuse box.
- If you are not familiar with code requirements, it is recommended to have the fixture installed by a certified electrician.
- Check that all parts and part packages are present before assembly.
- Carefully pull house wires down out of the junction box so that they are easily accessible to connect fixture wires.
- Place the mounting bracket up against the junction box with the screw collar loop pointing down towards the floor. Align each slot in the mounting bracket with each hole in the junction box.
- Thread one junction box screw into each slot in the mounting bracket and into holes in the junction box. Tighten the screws to secure the mounting bracket to the junction box. Make sure that house wires are still easily accessible and not pinched between the mounting bracket and ceiling.
- Strip 3/4 of insulation from ends of fixture wires.
- Carefully push fixture wires up through the bottom hole in screw collar loop attached to mounting bracket and out end of threaded pipe inside junction box. Pull fixture wires so they are easily accessible to connect to house wires.
- To aid in connecting fixture wires to house wires, temporarily connect second locking link to loop and screw collar loop.
- Slightly loosen the ground screw on the mounting bracket. Wrap the house ground wire (copper) around the ground screw, leaving enough ground wire to attach to fixture ground wire. Twist the end of fixture ground wire and end of house ground wire together. Twist the wire nut onto ends of wires. Completely tighten the wire nut.
- Twist end of house lead wire (black) and end of fixture lead wire together. Twist the wire nut onto ends of wires. Completely tighten the wire nut. Twist end of house neutral wire (white) and end of fixture neutral wire together. Twist the wire nut onto ends of wires. Completely tighten the wire nut.
- Wrap electrical tape around wire nuts and wires. Ensure wires are securely fastened into wire nuts.
- Carefully push all wires and wire nuts into junction box.
If you have any questions, call 800-613-3261 from Monday to Friday between 8:00 AM to 6:00 PM Eastern Time.
WARNING: DISCONNECT POWER AT THE MAIN FUSE BOX BEFORE INSTALLATION.
WARNING:
This fixture is intended for installation in accordance with the National
Electrical Code (NEC) and all local code specifications. If you are not
familiar with code requirements, installation by a certified electrician is
recommended.
Before assembly, remove all parts and part packages from box. If anything is
missing, please contact the retailer from which the product was purchased.
-
Carefully pull house wires down out of junction box so house wires are easily accessed to connect fixture wires.
-
If screw collar loop (W) is already attached to mounting bracket (A), proceed to Step 3. To assemble screw collar loop (W) to mounting bracket (A): Hold mounting bracket (A) so head of ground screw is pointing down towards floor. Hold threaded pipe so two hexnuts already attached to threaded pipe (E) are pointing down towards floor. From side of mounting bracket with ground screw head, screw short end of threaded pipe (E) into hole in center of mounting bracket (A) until hexnut on threaded pipe (E) touches mounting bracket. Thread hexnut (V) onto end of threaded pipe (E). Tighten hexnut (V) to secure threaded pipe (E) to mounting bracket (A). Thread screw collar loop (W) onto end of threaded pipe pointing down towards floor. Tighten screw collar loop up against hexnut on threaded pipe (E).
-
Place mounting bracket (A) up against junction box. Screw collar loop (E) should be pointing down towards floor. Align each slot in mounting bracket (A) with each hole in junction box.
-
Thread one junction box screw (B) into each slot in mounting bracket (A) and into holes in junction box. Tighten junction box screws (B) to secure mounting bracket (A) to junction box.
CAUTION: Make sure house wires are still easily accessible. DO NOT pinch wires between mounting bracket and ceiling.
CAUTION: At least one 6 inch stem must be used. -
Carefully push fixture wires up through bottom of 6 inch stem (N). Pull fixture wires out of top of 6 inch stem (N). Screw bottom of 6 inch stem (N) onto top of fixture body (O).
-
Determine desired hanging height of fixture. Select the quantity of stems (M) to achieve that height.
-
Carefully push fixture wires up through end of one 12 inch stem (M). Thread end of stem (M) onto top of stem (N).
-
Carefully push fixture wires through remaining stems (M). Screw stems (M) together keeping fixture wires taut. DO NOT pinch fixture wires between stems.
-
Push fixture wires up through bottom of loop (S). Thread loop onto top of last stem (M).
-
Slip threaded ring (F) down over fixture wires.
-
Position canopy (D) so outside of canopy is pointing down towards fixture. Slip hole in canopy (D) over end of fixture wires.
-
Strip 3/4” of insulation from ends of fixture wires.
-
Carefully push fixture wires up through hole in screw collar loop (W) attached to mounting bracket (A) and out end of threaded pipe inside junction box. Carefully pull fixture wires so they are easily accessible to connect to house wires.
-
To aid in connecting fixture wires to house wires, temporarily connect second locking link (G) to loop (S) and to screw collar loop (W). Slightly loosen ground screw on mounting bracket (A). Do not completely remove ground screw. Wrap house ground wire (copper) around ground screw, leaving enough ground wire
to attach to fixture ground wire. Twist end of fixture ground wire and end of house ground wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart below for correct wire connections.
Connect Supply (House) Ground Copper Wire to:
Bare Copper Wire or,
Bare Silver Wire or,
Green Insulated Wire.
15. Twist end of house lead wire (black) and end of fixture lead wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Twist end of house neutral wire (white) and end of fixture neutral wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart to the right for correct wire connections.
Wrap electrical tape (not included) around wire nuts (C) and wires. Ensure
wires are securely fastened into wire nuts.
- Carefully push all wires and wire nuts into junction box.
Connect Black Lead Supply (House) Wire to:| Connect White Neutral Supply (House) Wire to:
---|---
Black Wire or,| White Wire or,
Parallel Cord (Round and Smooth) or,| Parallel Cord (Square and Ridged) or,
No printed words on wire insulation or,| Printed words on wire insulation or,
Insulated Wire (other than green)
with Copper Conductor.
| Insulated Wire (other than green)
with Silver Conductor.
*When parallel wire (SPT 1 & SPT 2) is used: The lead wire is round in shape or smooth.
The neutral wire is square in shape or ridged.
- Remove second locking link (G) from loop (S) on stem (M) and screw collar loop (W).
- Raise canopy (D) up to ceiling. Pass hole in canopy (D) over screw collar loop (W). Position canopy (D) up against ceiling.
- Raise threaded ring (F) up to canopy (D). Screw threaded ring (F) onto screw collar loop (W). Tighten threaded ring (F) to secure fixture to ceiling.
- Attach locking link (G) to loop (S) on top of stem (M) and to screw collar loop (W).
- Lower ring (R) down over top of shade (K). Set ring (R) on bottom edge of shade (K).
- Raise shade (K) up to fixture. Pass hole in top of shade (K) over socket.
- Slip silicone washer (T) over socket. Thread socket ring (L) onto socket. Tighten socket ring (L) to secure shade (K) in place.
- Screw recommended bulb (E26 Edison bulb type, not included) into socket. Verify correct bulb wattage marked on socket of fixture.
WARNING: DO NOT exceed maximum bulb wattage.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>